Loading ...
The product complies with the European Safety Standards EN60335-2-30 and the European Standard Electromagnetic Compatibility (EMC) EN55014,
EN60555-2 and EN60555-3 These cover the essential requirements of EEC Directives 2006/95/EC and 2004/108/EC
[c] GDC Group Limited
All rights reserved. Material contained in this publication may not be reproduced in whole or in part, without prior permission in writing of Dimplex,
a division of GDC Group Ltd.
Electrical connection
This heater must be used on an ~ supply only and the voltage
marked on the heater must correspond to the supply voltage.
This heater is fitted with a rewirable plug incorporating a 13
amp fuse. In the event of replacing the fuse in the plug
supplied, a 13 amp fuse approved by ASTA to BS 1362 must
be used. If any other type of plug is used, a 15 amp fuse
must be fitted in the plug, the adaptor, or at the distribution
board.
IMPORTANT : If the plug is not suitable for your socket, the
13 amp plug should be removed. Before wiring the appropriate
plug, please note that the wires in this mains lead are
coloured in accordance with the following code :
BLUE : NEUTRAL
BROWN : LIVE
As the colours of the wires in the mains lead may not
correspond with the coloured markings in your plug, proceed
as follows :
Connect the BROWN wire to the terminal marked ‘L’ or coloured
RED. Connect the BLUE wire to the terminal marked ‘N’ or coloured
BLACK. Note : ‘L’ or ‘N’ wire must not be connected to the EARTH
terminal marked ‘E’ or ‘ ’ or coloured GREEN or GREEN
AND YELLOW. If in doubt, consult your electrician.
Operation
Switch – see Fig. 2
With the selector switch, the fan can be switched on or the
heat setting selected. The power indicating light illuminates
when the Switch is turned on.
Thermostat – see Fig. 2
In order to maintain a certain room temperature, set the
controller to ‘max.’. Operate the appliance at full power until
the required room temperature is reached. Set back the
thermostatic controller until the appliance switches off with
an audible ‘click’. This temperature will be kept almost
constant by the thermostatic control switching on and off
automatically. Please note that the appliance can only be
switched on when the thermostat setting is higher than the
room temperature.
With the thermostat knob set to ‘ ’ and the switch knob set
to the required heating output the appliance switches on
automatically when the temperature falls below +5°C . . .+8°C.
Safety
Overheat Protection
For your safety, this appliance is fitted with a thermal cutout.
In the event that the product overheats, the cutout switches
the heater off automatically.
To bring the heater back into operation, remove the cause of
the overheating, then unplug or turn off the electrical supply
to the heater for a few minutes. When the heater has cooled
sufficiently, re-connect and switch on the heater.
Fuselink
A thermal fuse link is provided as an added safety feature. If
the fuse link operates and opens circuit it is the result of
abnormal overheating within the appliance and servicing of
the appliance by a competent service engineer will be required
in order to ensure the future safe operation of the heater.
Customer services should be contacted, who will arrange
the replacement of any faulty parts and the fitting of a new
fuse link.
Cleaning
Switch off the appliance first and disconnect the plug from
the socket!· Clean the housing with a moist cloth, vacuum
cleaner or brush.· Do not use any abrasive or caustic cleaning
agents!· Do not use any flammable cleaning agents e.g. petrol
or spirit for cleaning the appliance.· Never immerse the
appliance in water! Danger to life!· Air inlet- and outlet area
should be cleaned with a vacuum cleaner regularly· If the
appliance is not used for extended periods, it must be
protected against excessive dust and dirt.
This heater is provided with an air filter. Dust and fluff can
accumulate in the filter and to avoid overheating of the element
the filter should be cleaned when required. To clean the filter
remove the filter bracket from the back of the heater. The
filter can be taken from the filter bracket and dust or fluff can
then be removed using a vacuum cleaner. When cleaning of
the filter is complete the filter should be refitted to the filter
bracket. The filter bracket should then be refitted to the rear
of the product.
Recycling
For electrical products sold within the
European Community. At the end of the
electrical products useful life it should not
be disposed of with household waste.
Please recycle where facilities exist. Check
with your Local Authority or retailer for
recycling advice in your country.
After Sales Service
Your product is guaranteed for 3 years from the date of
purchase. After sales information or assistance with this
product can be found on our website:
www.dimplex.co.uk/support.
Your rights under this guarantee are additional to your
statutory rights, which in turn are not affected by this
guarantee.
Please do not return a faulty product to us as this may result
in loss or damage and delay in providing you with a
satisfactory service.
If after following these steps your product still does not operate
you should return it to your point of purchase.
Please retain your receipt as proof of purchase.