Loading ...
Loading ...
Loading ...
3
Press the hour button to advance the clock to the
desired time. The hour numeral moves in one hour
increments. When passing 12 am, the “PM” indica-
tor will illuminate in the lower left hand corner of
the LCD screen.
Press the “minute” button to advance the minutes
to the desired time. Minutes move in one second
increments.
When complete, press the hour button again, or
wait for 15 seconds and your time change will be
accepted.
To Program the Brew Time
To program the brew time, press and hold the
program button for two seconds. The “prog”
symbol starts flashing in the lower right corner
of the LCD screen.
Press the hour button to advance the clock to the
desired time. The hour numeral moves in one hour
increments. When passing 12 am, the “PM”
indicator will illuminate in the lower left hand
corner of the LCD screen.
Press the “minute” button to advance the minutes
to the desired time. Minutes move in one second
increments.
When complete, press the “prog” button, or wait
for 15 seconds and your set time will be accepted.
To Activate the Auto Brew Cycle
To activate the auto brew mode, depress the “auto
on” button. The “auto” symbol will illuminate in
the upper right hand corner of the LCD screen.
The unit will now begin the brewing cycle at the
programmed time. When the programmed time
initiates the cycle, the red “ON” indicator light will
show that the brewing cycle has started.
NOTE: The unit will continue to attempt to
brew at the programmed time, each day, until
the Auto On button is turned off. The red
“ON” indicator light will illuminate each time
the attempt to brew is made.
If there is no water in the reservoir, the unit will
automatically shut off one minute later.
COFFEE PREPARATION
1. Place coffee maker on a solid flat surface.
Plug into 120V outlet.
2. Open thermal carafe lid in direction of
“OPEN” arrow. Fill thermal carafe with cold,
fresh water. Open hinged water reservoir
cover; pour water into reservoir opening.
Markings on water level indicator show
amount of water needed to make desired
number of cups of coffee.
TO AVOID OVERFLOW, DO NOT FILL
ABOVE 8-CUP MARK.
Close reservoir cover.
3. Before thermal carafe is returned to platform,
prewarm carafe by running warm water
through carafe. If warm water is not run
through carafe, when hot coffee flows into
carafe during brewing cycle the glass liner
may crack due to the temperature change.
Prewarming carafe will help keep coffee
warmer, and also prevent glass liner from
being damaged.
4. Return carafe lid to thermal carafe. To close lid,
turn it in direction of “CLOSE” arrow until it
fits tightly on carafe, and “POUR” arrow is
aligned with spout. Return empty thermal
carafe to platform. Be certain thermal carafe
lid is in “CLOSED” position and is securely
in place during brew cycle.
5. Open filter basket by grasping basket
handle and swinging outward. Insert a filter
into filter basket; make sure filter fits snugly
in basket. Use a fresh filter for each carafe
of coffee.
6. After placing 2 level tablespoons per cup of
ground coffee into cone filter, return basket to
closed position. To ensure safe operation, make
sure basket is closed securely.
7. With thermal carafe and basket securely in
place, press “ON” button; LED will light.
CAUTION: Coffee maker becomes very
hot during brew cycle; handle with extreme
care as hot parts and escaping steam may
cause burns.
8. The Brew-Through lid allows coffee to drip
from coffee maker through closed lid. When
coffee has completely stopped dripping into
thermal carafe and water level indicator is
empty, brew cycle is complete. When dripping
stops, Brew-Through lid will seal so coffee
freshness and temperature are preserved.
9. An audible “beep” tone will signal when brew
cycle is complete. Coffee maker will switch
off automatically.
10. After coffee grounds have cooled, carefully
open filter basket and discard used coffee filter
Loading ...
Loading ...
Loading ...