Loading ...
Loading ...
Loading ...
FM TUNER
Storing radio stations
You can store up to 30 radio stations. Select a preset
number 1-30.
1 Tune to a desired radio station and press PROG
briefly.
2 Press PROG while PROG is blinking to confirm the
storage.
PROG, the FM frequency and the preset number of
the stored station are displayed.
3 Store all desired stations this way.
Helpful Hint:
Already stored stations can be recognized by a preset
number.
Tuning to a stored radio station
1 Press ALBUM + / - repeatedly if necessary to select
the preset number of the desired radio station.
Radio play starts. The FM frequency and the pre-
set number (P1-30) of the stored station are dis-
played.
FM TUNER
Switching radio on/off
• Press FM/ once or more to switch the radio on/
off.
Display shows briefly Radio on or Radio off
respectively.
Use the remote control or set to tune to any FM station
automatically or manually.
Tuning to radio stations automatically
1 Press and hold or § for at least 2 seconds.
Display shows briefly Searching.The radio tunes
to a station with sufficient strength and radio play
starts. The FM frequency is displayed.
2 Repeat searching until you find the desired radio station.
Tuning to radio stations manually
1 Keep or § pressed.
2 Release or §, then briefly press or § again
when you are close to the desired frequency.
3 Briefly press or § repeatedly until you reach the
desired frequency.
Radio play starts. The FM frequency is displayed.
•To switch from radio play to CD play, press 2;.
Press to switch the radio off.
Helpful Hint:
To improve reception: The headphone wire is used as an FM antenna.
If necessary, move it for optimum reception.
Tuner operation is not affected if you open the CD lid to change a disc.
LOCK
You can lock the buttons of the set/ remote control respectively by switching the
slider to LOCK. With LOCK activated, you can avoid
accidental activation of other functions.
1 Switch the slider to LOCK to activate LOCK.
All buttons are locked. Hold is shown when you
press any button on the set / remote control
respectively. If the set is locked and switched off, Hold will be shown
only when pressed 2; .
2 To deactivate LOCK, switch the slider to OFF or UNLOCK.
ENVIRONMENTAL INFORMATION
•All redundant packing material has been omitted. We have done our utmost to
make the packaging easily separable into 4 materials: paper, PET, PE and PS.
•Your set consists of materials which can be recycled if disassembled by a
specialized company. Please observe the local regulations regarding the
disposal of packing materials, dead batteries and old equipment.
TROUBLESHOOTING
WARNING: Under no circumstances should you try to repair the unit yourself as
this will invalidate the warranty. If a fault occurs, first check the points listed,
before taking the unit for repair. If you are unable to solve a problem by following
these hints, consult your dealer or service center.
The CD player has no power, or playback does not start
•Check that your batteries are not dead or empty, that they are inserted
correctly, that the contact pins are clean.
•Your adapter connection may be loose. Connect it securely.
The indication Please insert CD is displayed
Check that the CD is clean and correctly inserted (label-side upward).
If your lens has steamed up, wait a few minutes for this to clear.
The indication Unfinalized CD is displayed
•CD-RW (CD-R) was not recorded properly. Use FINALIZE on your CD-recorder.
The indication Hold is on and/or there is no reaction to controls
If LOCK is activated, then deactivate it.
•Electrostatic discharge. Disconnect power or remove batteries for a few seconds.
The CD skips tracks
The CD is damaged or dirty. Replace or clean the CD.
•, or PROG is active. Switch off whichever is on.
No sound or bad sound quality.
pause might be active. Press 2;.
Loose, wrong or dirty connections. Check and clean connections.
•Volume might not be appropriately adjusted. Adjust the volume.
Strong magnetic fields. Check player’s position and connections. Also keep
away from active mobile phones.