Loading ...
Loading ...
Loading ...
Cleaning function en
21
.Cleaning function
Cl eani ng function
The "EcoClean" cleaning function is used to clean the
self-cleaning surfaces in both cooking compartments.
The self-cleaning surfaces (back panel, ceiling panel
and side panels) are coated with a porous, matt
ceramic material. This coating absorbs and breaks
down splashes from baking, roasting and grilling while
the oven is in operation. If the surfaces no longer clean
themselves adequately and dark patches appear, the
surfaces can be cleaned by the cleaning function.
Cleaning recommendation
The appliance records how long the bottom cooking
compartment is in operation and which operating mode
is used. When cleaning is recommended, ’– appears
in the display when the appliance is switched off. You
can dismiss this message by pressing any button
except the A button. The prompt will continue to be
displayed, however, until the cleaning function has been
run in full.
Note: You can completely reset the cleaning
recommendation counter by pressing and holding the
A button for approximately four seconds.
The prompt does not reappear until the appliance has
been used a certain number of times again.
Caution!
If you do not act on this cleaning recommendation, the
self-cleaning surfaces in the cooking compartment may
become damaged.
If your appliance is already very dirty, e.g. because you
have used it to cook fatty poultry or roasts, or if you
notice dark patches on the self-cleaning surfaces, do
not delay running the cleaning function until this prompt
appears. The more often or the earlier the appliance is
cleaned, the longer the self-cleaning surfaces retain
their ability to clean themselves. You can clean either of
the cooking compartments at any time as required
using the cleaning function.
Note: The counter for the cleaning recommendation
prompt will be reset following a power failure. It is
therefore a good idea to run the cleaning function after
a power failure has occurred.
Prior to initiating the cleaning function
Remove shelves, rails, accessories and ovenware from
the cooking compartment.
Cleaning the cooking compartment floor and the
inside of the appliance door
Remove the worst dirt from the cooking compartment
floor, the inside of the appliance door and the interior
lighting. Otherwise, patches will appear that can no
longer be removed.
Caution!
Do not use oven cleaner on the self-cleaning surfaces.
This will damage the surfaces. If oven cleaner does
come into contact with these surfaces, dab it off
immediately with water and a sponge cloth. Please to
not rub or use any abrasive cleaning materials.
~ "Cleaning" on page 19
:Warning – Risk of burns!
; The appliance will become very hot on the outside
during the cleaning function. Never touch the appliance
door. Allow the appliance to cool down. Keep children
away from the appliance.
Setting the cleaning function
Make sure you follow all the preparation instructions
before setting the cleaning function.
Main oven
The duration for the cleaning function is preset to one
hour. This duration cannot be changed.
1. Use the function selector to set EcoClean p.
The duration appears in the display.
2. Turn the temperature selector to cleaning setting p.
The cleaning function starts after a few seconds. The
cooking time counts down in the display.
Ventilate the kitchen while the cleaning function is
running.
An audible signal sounds when the cleaning function
has finished. The time shown in the display is zero.
Switch the appliance off by turning the function selector
to the "Off" position.
Top oven
1. Use the function selector to set EcoClean p.
2. Turn the temperature selector to cleaning setting p.
3. Switch off the appliance after 60 minutes.
Note: You can also set the timer to remind you after
60 minutes.
Ventilate the kitchen while the cleaning function is
running.
Delaying the end time
You can delay the end time if required. Before starting,
touch the v button until the "End" symbol is highlighted
on the display. Use the @ button to delay the end time.
The appliance will switch to standby after it is started.
Changing and cancelling
The end time can be changed while the appliance is on
standby.
If you would like to cancel the cleaning function, switch
the appliance off by turning the function selector to the
"Off" position.
Loading ...
Loading ...
Loading ...