Sencor SBL 4871WH Table mixer User Manual

SBL 4871WH

SBL 4872BK

TABLE BLENDER

Translation of the original manual

SBL 4871WH

SBL 4872BK

– 1 –

08/2024

2024, .

EN Table Blender

Important Safety Instructions

READ CAREFULLY AND STORE FOR FUTURE USE.

General Warnings

• Persons with reduced physical, sensory, or mental

capabilities or with alack of experience and knowledge

may use this appliance only if they are supervised or have

been instructed on how to use the appliance safely and

understand the potential hazards.

• This appliance is not to be used by children. Keep the

appliance and its supply out of the reach of children.

• Children must not play with the appliance.

• This appliance is designed for domestic use and similar

premises, such as:

– kitchenettes in shops, offices and other work

environments;

– agricultural farms;

– inhotels, motels andother residential environments

(inthese facilities the appliance is intended for use by

guests);

– bed and breakfast establishments.

• This appliance is not intended for commercial use.

– 2 –

08/2024

2024, .

Caution:

To avoid danger due to sudden resetting of the

thermal fuse, this appliance must not be powered

via an external switching device such as atime

switch, or connected to acircuit whose characteristic

is that it switches on and off periodically.

• If the power cord is damaged, have it replaced in

aprofessional service centre in order to prevent

adangerous situation. It is forbidden to use the appliance

with the power cable damaged.

• To avoid injury from the chopping blades, take extra care

when handling the blade unit, especially when assembling

the appliance, emptying the container, removing the blade

unit from the container and during cleaning.

• Take special care if you pour hot liquid into the blender

container, as it may splash out of the appliance due to

sudden evaporation.

Warning:

Improper or unintended use can lead to injury.

WARNING:

Always operate the blender with the lid in place, as

described inthis user'smanual.

• Never place your hand in the blender container when

placed on the motor unit.

• If you need to press down the food in the container, use

asuitable kitchen utensil such as akitchen spatula.

– 3 –

08/2024

2024, .

• The maximum operating time is 1.5 minutes. Allow the

appliance to cool for at least 5 minutes before using

it again. Do not exceed the maximum operating time

andobserve the cooling time of the appliance.

• Food processing times and speed settings are listed

in thechapter QUICK GUIDE TO PROCESSING

INGREDIENTS.

• Before replacing the accessories or accessible movable

parts, please turn the appliance off and disconnect it from

the power supply.

• Always disconnect the appliance from the power socket

if you are leaving it unattended and before assembly,

disassembly or cleaning.

• Clean the food contact surfaces of the appliance and its

accessories according to the instructions in the chapter

CLEANING AND MAINTENANCE.

Additional Important Safety Instructions forUse of the Appliance

• Use the appliance and its accessories in accordance with the instructions in this manual.

• The appliance is designed for mixing food and liquids. Never use the appliance for purposes other than those for which it was designed.

• The appliance is designed for indoor use. Do not use the appliance in an industrial environment or outdoors.

• It is forbidden to modify the surface of the appliance in any way, e.g. using self-adhesive foil, etc.

• Do not expose the appliance or its accessories to the outdoor environment, extreme temperatures, rapid temperature changes, direct sunlight or

excessive dust.

• Always place the appliance on aclean, flat, dry and stable surface. Do not place it on the edge of the table to prevent it from falling.

• Do not place the appliance and its accessories on or near an electric or gas hob. Keep it at asufficient distance from open fire, heating elements

andother sources of heat. Do not place it or any part of it into the freezer.

• Before connecting this appliance to apower socket, make sure the rated voltage stated on the product'srating label corresponds to the voltage in

your power socket.

• Do not place heavy objects on the power cord. Make sure the power cord does not hang over the edge of atable or that it does not touch ahot

surface.

• The use of an extension cable is not recommended.

• Only use the appliance with original accessories from the manufacturer.

Warning:

The use of non-original accessories can lead to adangerous situation.

• Before use, always make sure that no part of the appliance is damaged. Do not use the appliance if the motor unit, container, lid, blade unit or screw

nut is damaged in any way.

• Do not overfill the blender container. The maximum capacity of the blender container is indicated by the 1,500 ml mark.

• To avoid adangerous situation, never use the blender to process hard ingredients such as nutshells, bones, hard pits of apricots, peaches, mangoes,

etc.

• This appliance is not intended for preparing dough or mashed potatoes, whipping egg whites or grinding raw meat, etc.

• Do not use the appliance to mix ingredients such as sparkling water, baking soda, baking powder, yeast, etc.

• Take extra care when handling hot liquids and food. Hot steam or splashes of hot liquids or food can cause scalding.

– 4 –

08/2024

2024, .

• The blender container is temperature resistant up to 70°C. Never put food into it or pour liquids at higher temperatures. There is arisk of scalding

due to the container bursting. Placing hot food or pouring hot liquids into the blender container causes the surface to heat up. Avoid contact with hot

surfaces. For added safety, allow hot liquids and foods to cool to room temperature before placing in the blender container.

• Use the handle for carrying the blender container. Move the blender container in avertical position.

• Never mix hot foods or liquids. Allow them to cool down to room temperature before blending.

• Prior to connecting the appliance to apower socket, make sure that the appliance is properly assembled according to the instructions in this

user'smanual.

• The appliance is equipped with asafety lock that will not allow it to start if the container is not properly fitted to the motor unit.

Caution:

Do not use the appliance without the sealing ring of the blade unit or the screw nut that attaches the blade unit to the blender

container.

Never run the blender without the lid properly attached to the blender container.

Warning:

Avoid contact with rotating parts of the appliance.

To avoid the risk of serious injury or damage to the appliance, never insert your hands, fingers, kitchen utensils or other objects into

the blender container when it is attached to themotor unit.

• The appliance may vibrate during operation

• Do not turn on the appliance when it is empty. Incorrect use may negatively affect the appliance’slifetime.

• Always start the blender at the lowest speed before setting the desired speed.

• While blending, hold the lid of the container with one hand from above.

• The lid must be properly secured to the container for the entire time of operation. After removing the inner lid, food can be added to the blender

container through the lid opening. Stop the blender before adding food. Add ingredients slowly insmall doses. Do not add hot liquids or food. Do not

go over the maximum mark. After adding food or liquids, return the inner lid back to its place.

• If food sticks to the blade unit or blender container, switch off the appliance and unplug it from the power socket. Make sure that the blade unit has

stopped rotating. Carefully remove the container from themotor unit. Open the lid and use aspatula to clean the blade unit andthe inside of the

container. Check that only the ingredients intended for processing are in the container and close the lid properly again. Attach the container back to

themotor unit. Connect the power cord to thepower socket andcontinueblending.

• When making nut butters or processing other high-fat or thick foods, do not leave the appliance running for more than one minute after the blended

mixture begins to circulate in the container. During prolonged operation, the appliance may overheat.

• If the appliance is overloaded or overheated, the motor will stop automatically. Set the speed dial to position 0, disconnect the appliance from the

power socket andallow it to cool down for 30−60minutes. The appliance can be used again once it has cooled down. Divide larger batches of food

into several smaller batches or use food cut into smaller pieces.

• After use, set the speed dial to position 0 and disconnect the power cord from the power socket. Wait for the rotating parts to stop before removing

the container from the motor unit.

• Unplug the appliance from the power socket by pulling the plug. Do not pull the power cord. Otherwise, damage to the power cable or the socket

may occur.

• Do not connect or disconnect the power cord plug to or from the power socket with wet hands.

• None of the components of this appliance are intended for use inamicrowave or electric oven, etc.

• The blender container is not designed forstoring food.

• To avoid the risk of electric shock, do not immerse the motor unit, power cord or power cord plug in water or any other liquid, or wash these parts

under running water.

• Do not use the appliance if it is not working properly, if the motor unit has been immersed in water or if it shows any signs of damage. Take it to an

authorised service centre for inspection or repair.

• Do not make any adjustments to the appliance. Do not disassemble the motor unit.

• Do not repair the appliance yourself. All repairs should be carried out by an authorised service centre. Tampering with the appliance during the

warranty period may void the warranty.

• Store the appliance in adry and clean environment out of the reach of children and animals.

– 5 –

08/2024

2024, .

• Thank you for purchasing our SENCOR product; we hope it will serve

to your satisfaction.

• Prior to using this appliance, please read the user manual thoroughly,

even in cases when you are already familiar with the use of similar

types of appliances. Use the appliance only as described in this

user manual. Keep the manual for future reference. If you pass the

appliance on to another person, ensure that this user manual is

included.

• Carefully unpack the appliance and make sure not to discard any part

of the packaging material until you have found all its components. It

is recommended to keep the original packaging, packing material,

receipt and confirmation of the extent of the seller'sliability or warranty

certificate at least for the duration of the legal right of defective

performance or quality guarantee. When transporting the appliance,

we recommend packaging it again in the original box provided by the

manufacturer.

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

DESCRIPTION OF THE TABLE BLENDER AND ITS ACCESSORIES

(Fig. A)

A1 Inner lid

A2 Perimeter lid

A3 Lid seal

A4 Glass container with handle,

max. filling capacity 1.5 l

A5 Blade unit seal

A6 Blade unit with 6 chopping

blades

A7 Screw nuts for fixing the A6

blade unit to the A4 container

A8 Motor unit

A9 Speed dial

0 – stopping the appliance

operation

gears 1−5 (1 − lowest speed,

5 − highest speed)

P − PULSE mode to briefly

start the blender at

maximum speed

A10 LED indicates the connection

of the A8 motor unit to the

power socket.

A11 Feet with suction cups

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

THE PURPOSE OF USING THE TABLE BLENDER

• This table blender can be used toprepare smoothies,milkshakes,

blending spreads, sauces, soups or baby food, making nut butters,

crushing ice, etc.

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

BEFORE FIRST USE

• Take the appliance and its accessories out of the packaging materials.

• Remove the A2 perimeter lid from the neck of the container. Remove

the A1 inner lid from the A2 perimeter lid.

• Turn the A4 blender container upside down andplace it carefully on

an even, dry andstable surface. Unscrew the A7 nut in the clockwise

direction and remove the A6 blade unit from the A4 container.

• Wash the A4 blender container, the A2 perimeter lid, the A1 inner lid

and the A6 blade unit with warm water using afew drops of hand

dishwashing detergent. Then thoroughly rinse everything under

running water to remove any dishwashing detergent residue andwipe

dry with akitchen towel.

Caution:

When handling and cleaning the A6 blade unit, take

extra care not to cut yourself on the chopping blades.

Do not touch the chopping blades.

Warning:

To avoid the risk of electric shock, do not immerse

the A8 motor unit, power cord or power cord plug in

water or any other liquid, or wash these parts under

running water.

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ATTACHING THE BLADE UNIT TO THE CONTAINER (Fig. B)

• Turn the A4 blender container upside down andplace it carefully on

an even, dry andstable surface. Place the A6 blade unit in the A4

container so that the blades face inside the A4 container. Place the

A7 screw nut threaded down on the A6 blade unit. Turn the A7 screw

nut counter-clockwise to attach the A6 blade unit to the A4 blender

container. Tighten the A7 nut with areasonably large force. Pull the

A7 screw nut upwards to verify that the A6 blade unit is properly

attached to thecontainer. Turn the A4 blender container upside down.

Caution:

When handling the A6 blade unit, take extra care

not to injure yourself on the chopping blades. Do not

touch the chopping blades.

Do not use the A6 blade unit without the A5 seal or

the A7 screw nut.

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

FOOD PREPARATION

• Remove the peel from citrus fruits and fruits with inedible or too hard

skin, such as pineapple, mango, etc. Remove the central part of the

pineapple in addition to the peel.

• Fruit containing hard seeds or pits, such as apricots, peaches,

mangoes, etc., should be pitted or seedless. Remove the cores and

stems from fruits such as apples, pears, etc. Remove the stems and

leaves from the strawberries. Remove the nuts from the shells.

• Cut the food into evenly sized pieces of approximately 2 cm.

• The size of frozen ingredients (ice cubes, banana, strawberries,

mangoes, etc.) should also be around 2 cm.

• Ice cubes should be processed immediately after taking them out of

thefreezer.

• The blender is not intended for blending dried foods such as beans,

pepper, coffee beans, dry corn kernels, etc., or other hard foods that

cannot be cut with aknife.

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

USING THE TABLE BLENDER (Fig. C)

• Fill the A4 blender container with prepared food andliquids. Do not

overfill the A4 container above the 1,500ml mark, otherwise the A2

lid could be loosened during operation and the ingredients could be

splashed out of the A4 container. If you are processing ingredients

that gain volume duringthe course of blending (milk, etc.), fill the A4

container up to amaximum of 1,000ml. Separate larger amounts of

ingredients into several smaller batches andprocess it gradually.

• Place the A2 lid on the A4 blender container. With one hand hold the

A4 container by the handle and with the other hand press the A2 lid

evenly down so that it adheres to the neck of the A4 container around

its entire circumference. Insert the A1 inner lid into the A2 perimeter lid

andpress it down to engage the A2 perimeter lid.

Caution:

Always use the A2 perimeter lid with the A3 seal

properly fitted.

• Ensure that the A8 motor unit is disconnected from the power socket

and the A9 speed dial is set to 0.

• Make sure that the outer surface of the A4 blender container is clean

anddry. Place the assembled andfilled container on the A8 motor

unit.

Note:

The safety lock will not allow the blender to start if the A4

container is not properly fitted to the A8 motor unit.

Table Blender

User Manual

– 6 –

08/2024

2024, .

• Connect the power cord plug to apower socket. Connection of the A8

motor unit to the power socket is indicated by the A10 LED indicator lit.

• Adjust the speed using the A9 speed dial. Set the speed to put the

blender into operation. Start with the lowest speed setting, so that the

ingredients are mixed first, andthen gradually increase the speed

to the desired level. Recommended speed settings and processing

times are given in the chapter QUICK GUIDE TO PROCESSING

INGREDIENTS.

Caution:

The maximum continuous operation time of the

appliance is 1.5 minutes. Allow the appliance to cool

for 5 minutes before using it again. Do not exceed the

maximum operating time andobserve the cooling

time of the appliance.

• During operation, hold the A2 lid from above with one hand. To add

ingredients to the A4 container, stop the blender and carefully remove

the A1 inner lid. Slowly add the ingredients to the A4 container through

the hole in the A2 perimeter lid. Do not exceed the 1,500ml mark

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

QUICK GUIDE TO PROCESSING INGREDIENTS

Ingredients | dishes | drinks Quantity Speed selection Recommended blending time

Smoothies andcocktails* 750 ml 4−5 30−40 s

Children'smixed dishes 250 g 3 15−20 s

Spreads 250 g 2−3 10−15 s

Dressings 250 ml 3−4 15−20 s

Soups and sauces 750 ml 3−4 30−40 s

Peanut butter 250 g 2−3 5x 30 s**

Hard pastry for breadcrumbs 2 rolls (approx. 90 g) P (Pulse level) 5x 3s

Ice cubes 12 pcs P (Pulse level) 4−5x 3s

* Use PULSE mode when mixing drinks withfrozen fruit or ice cubes.

** Between each 30-second cycle, wipe the walls of the A4 container with akitchen spatula. Before cleaning the walls of the A4 container, set the A9

speed controller to position 0, disconnect the power cord from the power socket andwait for the rotating parts to stop. Remove the container from

the A8 motor unit andonly then, after removing the A2 lid, clean the walls of the A4 container. After the first cycle, add atablespoon of peanut oil.

Allow the blender to cool down for 5minutes after the first 3 cycles.

Note:

The above table serves only as arecommendation.

or add hot foods or liquids. Replace the A1 inner lid and continue

blending.

• To briefly start the blender at the highest speed, turn the A9 speed dial

to position P and hold it briefly in this position. After releasing, the A9

speed dial will automatically return to position 0. The pulse level is

used to briefly and repeatedly start the blender at the highest speed,

e.g. when crushing ice. Always hold the A9 speed dial in theposition P

only atshort intervals of afew seconds.

• Stop the blender operation by setting the A9 speed dial to position 0.

• After use, unplug the power cord from the power socket. Wait until the

rotating parts stop rotating and remove the assembled container from

the A8 motor unit.

• Remove the A2 lid andcarefully empty the contents of the A4

container.

• After each use, properly clean the parts that have come into contact

with food according to the instructions in the chapter CLEANING AND

MAINTENANCE.

CLEANING AND MAINTENANCE (Fig. D)

• Before any cleaning or maintenance, set the A9 speed dial to position

0 (stop operation) anddisconnect the power cord from the power

socket. After stopping the rotating parts, remove the container from

theA8 motor unit.

• Never use thinners, metal or other dishwashers or abrasive cleaners

for cleaning. The finish of the appliance and its accessories could be

damaged.

Warning:

To avoid the risk of electric shock, do not immerse

the A8 motor unit, power cord or power cord plug in

water or any other liquid, or wash these parts under

running water.

Caution:

When handling and cleaning the A6 blade unit, take

extra care not to cut yourself on the chopping blades.

Do not touch the chopping blades.

• Clean the appliance immediately after use. Do not store food in the A4

blender container or allow food remains to dry init. Dried food remains

are more difficult to remove andmay make it more difficult to remove

the A6 blade unit from theA4 container.

• Remove the A2 perimeter lid and the A1 inner lid from the container.

After emptying the A4 container, remove the A6 blade unit.

• Wash the A4 glass container, the A2 perimeter lid, the A1 inner lid and

the A6 blade unit thoroughly with warm water using afew drops of

hand dishwashing detergent. Then thoroughly rinse everything under

running water to remove any dishwashing detergent residue andwipe

dry with akitchen towel.

• A1 inner lid, A2 perimeter lid and A4 blender container (without A6

blade unit) are suitable for washing in adishwasher. Leave the A1 inner

lid and the A2 perimeter lid to be washed inthe dishwasher'supper

basket. You can leave the A4 blender container to be washed in the

lower dishwasher basket.

• The A4 blender container can also be cleaned by putting the blender

into operation for 30−40 seconds according to the instructions in the

chapter of USING THE TABLE BLENDER with the A4 container filled

with about 0.5l of clean water with the addition of 1 to 2drops of hand

dishwashing detergent. This will release most of the food remains.

After turning off anddisconnecting the blender from the power socket,

wait for the rotating parts to stop. Take the A4 container off theA8

motor unit. Remove the A2 lid andempty the contents of the A4

container. Disassemble the container into its individual parts. Rinse the

A4 glass container, the A2 perimeter lid, the A1 inner lid and the A6

blade unit thoroughly under running water to remove any residual dirt

anddishwashing detergent andwipe dry with akitchen towel.

– 7 –

08/2024

2024, .

• Check that the A3 lid seal and the A5 blade unit seal are clean.

Residual dirt can cause the seal not to perform its purpose properly.

• The A7 screw nut can be washed under clean running water with

ahand dishwashing detergent. After washing, wipe the A7 nut dry.

• Use aslightly damp cloth to remove dirt from the A8 motor unit. Wipe

the cleaned surface of the A8 motor unit dry with asoft cloth.

STORAGE

• Clean the blender and its accessories according to the instructions

in the chapter CLEANING AND MAINTENANCE. Before storing, the

blender andits accessories must be clean anddry.

• Store the blender and its accessories in aclean, dry place out of the

reach of children and pets.

TROUBLESHOOTING

Problem Possible Cause Solution

The blender cannot be turned on. The power

cord is connected to the power socket.

The A4 blender container is not properly

attached to the A8 motor unit.

Set the A9 speed dial to position 0. Disconnect

the power cord from the power socket. Attach

the assembled container to theA8 motor unit

properly.

There is afaint smell when first used. This is anormal occurrence. If the smell persistsafter several uses, please

contact an authorised service centre.

The blender suddenly stopped. Overheating or overload protection has been

activated.

Set the A9 speed dial to position 0. Disconnect

the power cord from the power socket. Let

the blender cool for 30–60 minutes. Divide

alarger batch of ingredients into several smaller

batches andblend them inablender gradually.

If the blender fails to start after cooling down,

contact an authorised service centre.

The A4 blender container is leaking. The A4 blender container is cracked. Stop using the cracked A4 container

andreplace it with anew container of the

original type.

The A6 blade unit is not properly attached to

the A4 blender container.

Empty the contents of the A4 container and

properly attach the A6 blade unit to the A4

blender container with the A7 screw nut.

The A5 sealing ring does not extend around the

perimeter to the A6 blade unit or is not fitted at

all to the A6 blade unit.

Empty the contents of the A4 container.

Unscrew the A7 nut. Remove the A6 blade unit

from the A4 blender container. Align the A5

sealing ring so that it adheres to the A6 blade

unit along the entire circumference or place it on

the A6 blade unit andmake sure that it adheres

toit along the entire circumference. Attach the

A6 blade unit to the A4 blender container with

the A7 screw nut and tighten the A7 nut with

areasonably large force.

An unusual sound or an abnormal vibration can

be heard during operation.

The A6 blade unit is not properly attached to

the A4 blender container.

Set the A9 speed dial to position 0. Disconnect

the power cord from the power socket. Wait

until the rotating parts stop rotating. Take the

assembled container off theA8 motor unit.

Empty the contents of the A4 container and

tighten the A7 screw nut properly.

There are too many ingredients in the A4

blender container.

Set the A9 speed dial to position 0. Disconnect

the power cord from the power socket. Wait

until the rotating parts stop rotating. Take the

assembled container off theA8 motor unit.

Remove the A2 lid and remove some of the

ingredients from the A4 container.

The A6 blade unit is jamming. There are too many ingredients in the A4

blender container or the ingredients are cut into

too large pieces.

Set the A9 speed dial to position 0. Disconnect

the power cord from the power socket. Wait

until the rotating parts stop rotating. Take

the assembled container off theA8 motor

unit. Remove the A2 lid and remove part of

the ingredients from the A4 container or use

ingredients cut into smaller pieces.

– 8 –

08/2024

2024, .

TECHNICAL SPECIFICATIONS

Rated voltage range ................................................................................220−240 V

Rated frequency ..........................................................................................50–60 Hz

Rated input ..........................................................................................................1250 W

Safety class (for electric shock protection) ............................................................ II

Noise level .......................................................................................................85 dB(A)

Blender container capacity ....................................................................................1.5 l

Operating cycle ..................................................................................................1.5 min

Cooling time ............................................................................................................5 min

The declared noise emission level of the appliance is 85 dB(A), which

represents alevel Aof acoustic power with respect to areference acoustic

power of 1 pW.

Glossary of technical terms

Safety Class for Electric Shock Protection:

Class II – Electric shock protection is provided by double or heavy-duty

insulation.

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

EXPLANATION OF SYMBOLS PLACED ON THE PRODUCT OR INTHE

ACCOMPANYING DOCUMENTATION

Read the user'smanual.

Product with protection class II

The product meets all the basic requirements of the

applicable EU directives.

This symbol on products or original documents means that

used electric or electronic products must not be added to

ordinary municipal waste.

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

INSTRUCTIONS AND INFORMATION ON DISPOSAL OF USED

PACKAGING MATERIAL

Dispose of used packaging material at the location designated by the

municipality for waste disposal.

DISPOSAL OF USED ELECTRICAL AND ELECTRONIC EQUIPMENT

Used electrical andelectronic products must not be added to ordinary

municipal waste. For proper disposal and recycling of these products,

deliver them to designated collection points. Alternatively, in some

European Union states or other European countries the products can be

returned to the local retailer when buying an equivalent new product. By

properly disposing of this product, you help preserve valuable natural

resources and contribute to preventing potential negative impacts on the

environment and human health resulting from improper waste disposal.

For further details, contact your local authorities or the nearest collection

point. Fines may be imposed for improper disposal of this type of waste in

accordance with national regulations.

For Business Entities in European Union States

To dispose of electric or electronic equipment, request necessary

information from your retailer or supplier.

Disposal in Other Countries Outside the European Union

This symbol is valid in the European Union. If you wish to dispose of this

product, request the necessary information about the correct disposal

method from the local council or from your retailer.

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Changes to text and technical parameters are reserved.

Sencor SBL 4871WH Table mixer

Product's Documents

User Manual

Specifications

Sencor SBL 4871WH Questions and Answers