DSA60
DSA72
3 POINT DRUM
SPIKE AERATOR
5
6
DRUM SPIKE AERATOR PARTS ASSEMBLY (DSA60, DSA72)
PARTS LIST (DSA60, DSA72)
GENERAL SAFETY RULES
OPERATIONAL SAFETY
EQUIPMENT SAFETY GUIDELINES
CAUTION
1. Select an area for assembly that is clean and free of
any debris which might cause persons working on the
assembly to trip.
2. Do not lift heavy parts or assemblies. Use crane, jack,
tackle, fork trucks, or other mechanical devices.
3. Preview the assembly instructions in your operator’s
manual before proceeding further.
4. If the assembly instructions call for parts or assem-
blies to be blocked up, use only blocking material that is
in good condition and is capable of handling the weight of
the assembly to be blocked. Also ensure that the blocking
material is on a clean, dry surface.
5. Never put hands, or any part of the body, under
blocked-up assemblies if at all possible.
6. After completing assembly, thoroughly inspect the
machine to be sure that all nuts, bolts, hydraulic fittings,
or any other fastened assemblies have been thoroughly
tightened.
7. Before operating the machine, thoroughly read the
operation section of your operator’s manual.
8. Before operating, read the machine section of your
operator’s manual to be sure that any parts requiring
lubrication, such as the gearbox, are properly lubricated to
avoid any possible damage.
9. Before operating the equipment — if you have any
questions regarding the proper assembly or operation,
contact your dealer or representative.
3. This equipment is dangerous to children and persons
unfamiliar with its operation. The operator should be a
responsible adult familiar with your machinery and trained
in this equipment’s operations. Do not allow persons to
operate or assemble this unit until they have read this
manual and have developed a thorough understanding of
the safety precautions and of how it works.
4. Never exceed the limits of a piece of machinery.
5. Do not modify the equipment in any way. Unauthorized
modification may impair the function and could affect the
life of the equipment.
1. The use of this equipment is subject to certain hazards
which cannot be protected against by mechanical means
or product design. All operators of this equipment must
read and understand this entire manual, paying particular
attention to the operating procedures prior to use. If there
is something in this manual you do not understand, ask
your supervisor or your dealer to explain it to you.
2. Personal protection equipment, including hard hat,
safety glasses, safety shoes, and gloves, is recommend-
ed during assembly.
3. Never permit any person to ride or board the implement
at any time.
4. A heavy load can cause instability in driving a
tractor/skid loader. Make sure the front or rear of the
tractor/skid loader is properly counter-balanced with
weights. Always drive slowly — especially around turns.
An unstable tractor/skid loader could steer badly and
possibly tip over, causing injury or death.
5. Most accidents occur because of neglect or careless-
ness. Keep all helpers and bystanders at a safe distance.
6. Do not operate close to ditches or creeks. Slow down
when operating over rough ground.
7. When adjusting the angle of the moldboard assembly,
be sure that your feet are never under the rear blade.
8. Be careful to avoid catching the rear blade on stumps
or other immovable objects.
1. Never use alcoholic beverages or drugs which can
hinder alertness or coordination while operating this
equipment. Consult your doctor about operating this
machine while taking prescription medications.
2. Review the safety instructions with all users annually.
THE FOLLOWING SAFETY PRECAUTIONS SHOULD BE
THOROUGHLY UNDERSTOOD BEFORE ATTEMPTING TO
BEGIN ASSEMBLING THIS MACHINE
MAINTENANCE SAFETY
1. Keep all persons away from the operator control area
while performing adjustments, service, or maintenance.
2. Periodically tighten all bolts, nuts, and screws and
check that all cotter pins are properly installed to ensure
the unit is in a safe condition.
3. Never use your hands to locate a hydraulic leak on
attachments. Use a small piece of cardboard or wood.
4. Never replace hex bolts with less than grade five bolts
unless otherwise specified. Refer to the bolt torque chart
for head identification markings.
1. Store the unit in an area away from human activity. Do
not permit children to play on or around the stored unit.
2. Make sure all parked machines are on a hard, level
surface and engage all safety devices.
3. If blocking is used, make sure it is solid and secure
before leaving the area.
ALWAYS OBEY ALL SAFETY RULES!
ALWAYS BE CAREFUL!
STORAGE SAFETY
DRUM SPIKE AERATOR PARTS ASSEMBLY (DSA60, DSA72)
Drum Spike Aerator Parts Assembly (DSA60, DSA72)
PARTS LIST (DSA60, DSA72)
Parts List (DSA60, DSA72)
Parts# Description Quantity
1
2
3
4
5
6
7
8
9
10
11
12
13
The roller weldment
Frame
A-stand
The brace weldment
Pin
Bearing UCP205
Bolt M12*80
Flat washer Φ12
Lock Nut M12
Bolt M12*80
Lift Pin
O Pin
Top Pin
1
1
1
1
1
2
4
8
8
4
2
3
1
