INSTALLATION MANUAL
TRUFIG VX-VXQ SQUARE SOLID SURFACE
page 1 of 3
336-0151 REV CS
TRUFIG
INTRODUCTION
This installation guide will provide instructions to install a VX-VXQ Square speaker into a routable solid surface.
TOOLS NEEDED:
Plunge Router
Amana 45464-S router bit (see illustration on last page)
1/2 inch top bearing router bit.
3/8 drill bit
Power drill
Jig saw
Double-sided tape
Clamps
Corner chisel
SETTING UP THE PLUNGE ROUTER
1. Locate the SQR Depth Tool and Pocket Template.
Place the appropriate pocket (VX or VXQ; based on
model to be installed) under the Pocket Template
Depth Tool opening. Center it with the Depth
Tool hole.
2. With the Amana 45464-S bit installed in the plunge
router, set the depth of the plunge router tool.
POSITIONING
1. Locate where the speaker is to be installed.
2. Create center lines on the speaker location long enough
so the Router Template Center Lines can be matched.
Note: to avoid marking the finished surface, apply
masking tape where the lines are to be drawn. Draw
lines on the tape.
SQR Pocket Template
SQR Depth Tool
page 2 of 3
PLUNGING & CUTTING THE POCKET
1. Locate the Center Support Template and Pocket Template.
Apply double-sided tape to the back of the Center Support
Template.
2.
Align the Center Lines of the Center Support Template
with the lines on the surface to be cut.
3. Secure the Center Support Template in place
.
4. Apply double-sided tape to the back of the
SQR Pocket Template.
5. Align the Center Lines of the SQR Pocket Template
with the lines in the surface to be cut.
6. Secure the SQR Pocket Template in place. Clamps
can also be used.
7. Align the Plunge Router between the Pocket Template
and the Center Support Template. Plunge the router
bit to remove material between the Center Support and
the Pocket Template inner edge.
Note: in hard woods more than 1 pass may be
needed.
8. Once all the material is removed, drill a 3/8 inch hole
about 1/8 of an inch from the center support template
edge
Blue Tape
Working Surface
not shown
page 3 of 3
10. Remove and discard the center cut material.
Remove the Pocket Router Template.
CUTTING AN OPENING FOR THE
SPEAKER BODY
1. Retrieve that ID Template and apply double sided tape
to the back of it.
2. Center the ID Template using the center lines on the
surface to be cut.
3. With the 1/2 inch top bearing bit installed in the
plunge router, cleanly cut along the template to remove
the leftover material.
Note: this step is important to have both openings
concentric.
4.
Remove the ID template.
5.
Using a Square Chisel, square all four corners.
6.
Test fit the loudspeaker. If needed, re-center the
Pocket Router Template to plunge route/deepen
the pocket for the speaker flange.
Note: DO NOT CUT THROUGH THE MATERIAL BASED
ON POCKET TEMPLATE DIMENSIONS. ONLY CUT
ALONG THE CENTER SUPPORT TEMPLATE.
9. Using a jigsaw, cut through the material along
the edge of the round Center Support Template.
Maintain approximately 1/8 inch from the center support.
Scan QR code for additional information and resources. For technical
support call (949) 492-7777 or visit www.trufig.com/support/#visual
®
2024 SONANCE All rights reserved. TRUFIG is a registered trademark of Dana Innovations. Due to continuous product improvement, all features
and specifications are subject to change without notice. For the latest SONANCE and TRUFIG product specification information visit our website at
www.trufig.com or www.sonance.com.
991 Calle Amanecer - San Clemente, CA 92673 USA • Phone: 949.492.7777 • Fax: 949.361.5151 • Technical Support: 949.492.7777 • www.sonance.com
1
⁄
4
1
⁄4
1
⁄4
3
⁄4
Amana 45464-S
