3 POINT 6-WAY
REAR BLADE
RB60S, RB72S, RB84S
GENERAL SAFETY RULES
1
www.mechmaxx.com
1. Select an area for assembly that is clean and free of any debris which might cause persons working on the assembly
to trip.
2. Do not lift heavy parts or assemblies. Use crane, jack, tackle, fork trucks, or other mechanical devices.
3. Preview the assembly instructions in your operator’s manual before proceeding further.
4. If the assembly instructions call for parts or assemblies to be blocked up, use only blocking material that is in good
condition and is capable of handling the weight of the assembly to be blocked. Also ensure that the blocking material is
on a clean, dry surface.
5. Never put hands, or any part of the body, under blocked-up assemblies if at all possible.
6. After completing assembly, thoroughly inspect the machine to be sure that all nuts, bolts, hydraulic fittings, or any
other fastened assemblies have been thoroughly tightened.
7. Before operating the machine, thoroughly read the operation section of your operator’s manual.
8. Before operating, read the machine section of your operator’s manual to be sure that any parts requiring lubrication,
such as the gearbox, are properly lubricated to avoid any possible damage.
9. Before operating the equipment — if you have any questions regarding the proper assembly or operation, contact your
dealer or representative.
1. Never use alcoholic beverages or drugs which can hinder alertness or coordination while operating this equipment.
Consult your doctor about operating this machine while taking prescription medications.
2. Review the safety instructions with all users annually.
3. This equipment is dangerous to children and persons unfamiliar with its operation. The operator should be a responsible
adult familiar with your machinery and trained in this equipment’s operations. Do not allow persons to operate or assem-
ble this unit until they have read this manual and have developed a thorough understanding of the safety precautions and
of how it works.
4. Never exceed the limits of a piece of machinery.
5. Do not modify the equipment in any way. Unauthorized modification may impair the function and could affect the life of
the equipment.
CAUTION
EQUIPMENT SAFETY GUIDELINES
1. The use of this equipment is subject to certain hazards which cannot be protected against by mechanical means or
product design. All operators of this equipment must read and understand this entire manual, paying particular attention
to the operating procedures prior to use. If there is something in this manual you do not understand, ask your supervisor
or your dealer to explain it to you.
2. Personal protection equipment, including hard hat, safety glasses, safety shoes, and gloves, is recommended during
assembly.
3. Never permit any person to ride or board the implement at any time.
4. A heavy load can cause instability in driving a tractor/skid loader. Make sure the front or rear of the tractor/skid loader
is properly counter-balanced with weights. Always drive slowly — especially around turns. An unstable tractor/skid loader
could steer badly and possibly tip over, causing injury or death.
OPERATIONAL SAFETY
THE FOLLOWING SAFETY PRECAUTIONS SHOULD BE THOROUGHLY UNDERSTOOD BEFORE
ATTEMPTING TO BEGIN ASSEMBLING THIS MACHINE
GENERAL SAFETY RULES
2
www.mechmaxx.com
ALWAYS OBEY ALL SAFETY RULES!
ALWAYS BE CAREFUL!
1. Keep all persons away from the operator control area while performing adjustments, service, or maintenance.
2. Periodically tighten all bolts, nuts, and screws and check that all cotter pins are properly installed to ensure the unit
is in a safe condition.
3. Never use your hands to locate a hydraulic leak on attachments. Use a small piece of cardboard or wood.
4. Never replace hex bolts with less than grade five bolts unless otherwise specified. Refer to the bolt torque chart for
head identification markings.
MAINTENANCE SAFETY
1. Store the unit in an area away from human activity. Do not permit children to play on or around the stored unit.
2. Make sure all parked machines are on a hard, level surface and engage all safety devices.
3. If blocking is used, make sure it is solid and secure before leaving the area.
STORAGE SAFETY
5. Most accidents occur because of neglect or carelessness. Keep all helpers and bystanders at a safe distance.
6. Do not operate close to ditches or creeks. Slow down when operating over rough ground.
7. When adjusting the angle of the moldboard assembly, be sure that your feet are never under the rear blade.
8. Be careful to avoid catching the rear blade on stumps or other immovable objects.
GENERAL SAFETY RULES
3
www.mechmaxx.com
PARTS DIAGRAM
PARTS DIAGRAM
1
2
2
2
2
3
1
2
2
1
3
3
1
1
1
2
3
1
1
1
1
1
5/6/7
5/6/7
5/6/7
5/6/7
Parts# Description Quantity
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
Frame
Flat washer φ22
Spring washer φ22
Nut M22
Lift Pin
O Pin
Manual Box
Bolt M8*25
Lock Nut M8
Bolt M30*140
Flat washer φ30
Lock Nut M16
Stand
Lock Pin
Pinφ19
L Pin 1
R Pin
Towing Boom
Angle Plate Assembly
L Pin 2
Moldboard
Blade
Bolt M16*45
Flat washer φ16
Spring washer φ16
Nut M16
4
www.mechmaxx.com
PARTS LIST
PARTS LIST
