SAFETY DATA SHEET
Page 1 of 6
HFT-96084
Prepared to OSHA, ACC, ANSI, NOHSC, WHMIS, 2001/58 & 1272/2008/EC Standards SDS Revision: 1.1 SDS Revision Date: 7/27/2015
1. PRODUCT & COMPANY IDENTIFICATION
1.1 Product Name:
FLINT STRIKER
1.2 Chemical Name:
Mixture
1.3 Synonyms:
P/N 96084
1.4 Trade Names:
Chicago Welding
1.5 Product Uses & Restrictions:
Flint Striker
1.6 Distributor’s Name:
Harbor Freight Tools USA, Inc.
1.7 Distributor’s Address:
26541 Agoura Road, Calabasas, CA 91302 USA
1.8 Emergency Phone:
CHEMTREC: +1 (703) 527-3887 / +1 (800) 424-9300 (CCN 676687)
1.9 Business Phone / Fax:
+1 (805) 388-1000
2. HAZARDS IDENTIFICATION
2.1 Hazard Identification:
This product is classified as a HAZARDOUS SUBSTANCE but not as DANGEROUS GOODS
according to the classification criteria of NOHSC: 1088 (1999) and ADG Code (Australia).
Risk of burning off for fine material or explosions after raising the dust.
DANGER! FLAMMABLE SOLID. MAY CAUSE AN ALLERGIC SKIN REACTION. CAUSES
SERIOUS EYE IRRITATION. MAY BE HARMFUL IF INHALED.
Classification
: Flam. Sol. 1Skin Sens. 1B; Eye Irrit. 2; Acute Tox. Inh. 5
Hazard Statements
(H): H228 – Flammable solid. H317 – May cause an allergic skin reaction.
H319 – Causes serious eye irritation. H333 – May be harmful if inhaled.
Precautionary Statements
(P): P210 – Keep away from heat, hot surfaces, sparks, open flames
and other ignition sources. No smoking. P261 – Avoid breathing dust. P264 – Wash thoroughly
after handling. P280 – Wear protective gloves/eye protection/face protection. P304 + P312 – IF
INHALED: Call a POISON CENTER/doctor if you feel unwell. P302+P352 – IF ON SKIN: Wash
with soap and water. P333+P313 – If skin irritation occurs: Get medical advice/attention.
P305+P351+P338 – IF IN EYES: Rinse immediately with water for several minutes. Remove
contact lenses if present and easy to do. Continue rinsing. P370+P378 – In case of fire: Use Dry
sand or salt (NaCl), class D dry-powder extinguisher. DO NOT USE water, CO
2
-extinguisher and
halogenated agents. P501 – Dispose of contents/container to a licensed treatment, storage or
disposal facility (TSDF).
3. COMPOSITION & INGREDIENT INFORMATION
CHEMICAL NAME(S) CAS No. RTECS No.
EINECS No. %
EXPOSURE LIMITS IN AIR (mg/m
3
)
ACGIH NOHSC OSHA
OTHER
ppm ppm ppm
TLV STEL
ES-
TWA
ES-
STEL
ES-
PEAK PEL STEL IDLH
CERIUM
7440-45-1 FK485000 231-154-9 30-60 NA NA NF NF NF NA NA NA
Flam. Sol. 1; H228
LANTHANUM
7439-91-0 NA 231-099-0 10-30 NA NA NF NF NF NA NA NA
NEODYMIUM
7440-00-8 QO8575000 231-109-3 10-30 NA NA NF NF NF NA NA NA
PRASEODYMIUM
7440-10-0 NA 231-120-3 5-10 NA NA NF NF NF NA NA NA
Pyr. Sol. 1; H250
SAMARIUM
7440-19-9 231-128-7 0.1-1.0
NA NA NF NF NF NA NA NA
Flam. Sol. 2; Water-react.3;H228,H261
4. FIRST AID MEASURES
4.1 First Aid:
Ingestion: Ingestion is unlikely; however, particulates from grinding or cutting may be ingested. DO NOT INDUCE
VOMITING. Contact ChemTrec at +1 (703) 527-3887 or the nearest Poison Control Center or local
emergency telephone number for assistance and instructions. Seek immediate medical attention. If
vomiting occurs spontaneously, keep victim’s head lowered (forward) to reduce the risk of aspiration.
Eyes
: Flush eyes thoroughly with copious amounts of water for at least 15 minutes, holding eyelid(s) open to
ensure complete flushing. If irritation persists, seek immediate medical attention.
Skin
: Remove contaminated clothing and wash affected areas with soap and water. If irritation persists, seek
prompt medical attention. Do not wear contaminated clothing until after it has been properly cleaned.
Inhalation
: Remove victim to fresh air at once. If breathing is difficult, administer supplemental oxygen and seek
immediate medical attention. If breathing stops, perform artificial respiration.
4.2 Effects of Exposure:
Ingestion: Not expected route of exposure. Ingestion may cause gastrointestinal irritation, nausea, and/or vomiting.
Eyes
: None expected. May be slightly irritating.
Skin
: None expected. May cause sensitization in some sensitive individuals.
Inhalation
: None expected. Fumes may cause irritation to nasal membranes.
4.3 Symptoms of Overexposure:
No known or reported by manufacturer.
4.4 Acute Health Effects:
No known or reported by manufacturer
SAFETY DATA SHEET
Page 2 of 6
HFT-96084
Prepared to OSHA, ACC, ANSI, NOHSC, WHMIS, 2001/58 & 1272/2008/EC Standards SDS Revision: 1.1 SDS Revision Date: 7/27/2015
4. FIRST AID MEASURES – cont’d
4.5 Chronic Health Effects:
No known or reported by manufacturer
4.6 Target Organs:
No known or reported by manufacturer
4.7 Medical Conditions
Aggravated by Exposure:
Individuals with allergies or impaired respiratory function may have
symptoms worsened by exposure to welding fumes; however, such
reaction cannot be predicted due to the variation in the composition
and in the quantity of the decomposition products.
HEALTH
1
FLAMMABILITY
0
PHYSICAL HAZARDS
0
PROTECTIVE EQUIPMENT
B
EYES SKIN
5. FIREFIGHTING MEASURES
5.1 Fire & Explosion Hazards:
This product is not flammable. Welding slag or sparks may cause fire. Manmade alloy, .mainly
containing cerium and lanthanum. Cerium will burn when heated. Lanthanum will create spark
when struck.
5.2 Extinguishing Methods:
Water, Dry Chemical, Foam, Carbon Dioxide.
5.3 Firefighting Procedures:
Fight fires as for surrounding materials. Firefighters should wear a MSHA/NIOSH approved or
equivalent self-contained breathing apparatus (SCBA) and protective clothing. Fire should be fought
from a safe distance. Keep containers cool until well after the fire is out. Prevent runoff from fire
control or dilution from entering sewers, drains, drinking water supply, or any natural waterway.
6. ACCIDENTAL RELEASE MEASURES
6.1 Spills:
Before cleaning any spill, individuals involved in spill cleanup must wear appropriate Personal Protective Equipment
including gloves, glasses and NIOSH approved (or equivalent) dust respirator. Spilled product may produce a tripping
hazard. Particulate from grinding, welding or burning may produce a slipping hazard. Carefully vacuum or sweep up
the particulate, slag, dusts or powders. Dispose of properly in accordance with local, state and federal regulations.
Wash all affected areas. Remove any contaminated clothing and wash thoroughly before reuse. Keep spills and
cleaning runoffs out of drains, municipal sewers and open bodies of water.
7. HANDLING & STORAGE INFORMATION
7.1 Work & Hygiene Practices:
Avoid contact to eyes, skin, and mucous membranes. Avoid inhalation of vapors, gases, fumes and dusts. Wash
thoroughly after handling and use. Do not smoke, eat, drink, chew gum or tobacco, or apply cosmetics within the
working area. Do not store or bring tobacco products, gum, food, drinks or cosmetics within the working area. Otherwise
follow the standards of good industrial hygiene practices.
7.2 Storage & Handling:
No unusual methods are required. Keep product contained and retain all warning and identity labels. Preferred storage
is a sheltered warm area with temperature and humidity control to prevent high humidity and “going through the dew
point.” Keep away from incompatible materials listed in Section 10. Open containers slowly on a stable surface. Keep
container tightly closed when not in use.
7.3 Special Precautions:
Read and understand the manufacturer’s instructions and the precautionary label on this product. See American
National Standard Z-49.1, “Safety in Welding, Cutting and Allied Processes,” published by the American Welding
Society, P. O. Box 351040, Miami, FL 33135 and OSHA Publication 2206 (29 C.F.R. 1910), U.S. Government Printing
Office, Superintendent of Documents, P.O. Box 371954, Pittsburgh, PA 15250-7954 for additional details regarding fire
and explosion control, exposure control and other special precautions.
8. EXPOSURE CONTROLS & PERSONAL PROTECTION
8.1 Exposure Limits:
ppm (mg/m
3
)
CHEMICAL NAME(S)
ACGIH NOHSC OSHA OTHER
TLV STEL ES-TWA
ES-
STEL
ES-
PEAK PEL STEL IDLH
8.2
Ventilation & Engineering
Controls:
Use industrial hygiene monitoring equipment to ensure that exposure does not exceed threshold limit values. Use with
adequate ventilation (e.g., open doors and windows, local exhaust ventilation). Ensure appropriate decontamination
equipment is available (e.g., sink, safety shower, eye-wash station). Use in a chemical fume hood when working with
large quantities of product and provide adequate ventilation (e.g., local exhaust ventilation, fans).
8.3 Respiratory Protection:
CAUTION: Welding or cutting may produce fumes and gases hazardous to health. Avoid breathing
these fumes and gases. Use adequate ventilation. Use NIOSH approved respiratory protection. See
ANSI Z49.1-1967 Safety in Welding and Cutting published by the American Welding Society. Keep the
exposure within legal limits. In the worker’s breathing zone and the general area, the fumes and gases
must be kept below the TLVs and the equivalent exposure must compute to less than one. Keep
exposure as low as possible. Use respirable fume respirator or air supplied respirator when welding in
confined space or where local exhaust or ventilation does not keep exposure below the TLV. Where
respiratory protection is necessary, NIOSH approved respiratory protection should be used. The
selection of the appropriate respiratory protection (dust respirator, etc.) should be based on the actual
or potential airborne contaminants and their concentrations present.
SAFETY DATA SHEET
Page 3 of 6
HFT-96084
Prepared to OSHA, ACC, ANSI, NOHSC, WHMIS, 2001/58 & 1272/2008/EC Standards SDS Revision: 1.1 SDS Revision Date: 7/27/2015
8. EXPOSURE CONTROLS & PERSONAL PROTECTION – cont’d
8.4 Eye Protection:
Wear helmet or use face shield with filter lens according to ANSI Z87.1. Provide protective screens and
flash goggles, if necessary, to shield others. Wear safety glasses with UV protective side shields or
goggles. Wear contact lenses in combination with safety eyewear, except where the contact lenses
create a likelihood of injury from intense heat, highly particulate atmosphere, or where their use is
prohibited. Use equipment for eye protection tested and approved under appropriate government
standards such as NIOSH (US) or EN 166(EU).
8.5 Hand Protection:
Wear head, hand and body protection that help to prevent injury from hot metal, sparks, slag, infrared
radiation, UV radiation, abrasions, contusions and heat stress. Protective clothing will not generally
prevent shock except for leather if kept dry. Gloves made of leather with inside seams (or those that
give equal performance) are preferred. If necessary, refer to U.S. OSHA 29 CFR §1910.138, the
appropriate standards of Canada, or the EU member states.
8.6 Body Protection:
Wear head, hand and body protection that help to prevent injury from radiation, sparks and electrical
shock. Wear flame resistant ear plugs to keep sparks out of ears. See ANSI Z-49.1. The clothing may
include heat/fire resistant gloves, overalls, aprons, sleeves, footwear, welder’s spats and head cover.
Wear garments made of leather, heavyweight tightly woven wool or cotton. Keep clothing clean (free of
oil, grease or solvents) and in good repair. Do not wear clothing with frayed edges, tears or holes. Do
not roll up sleeves or trousers (pants should not be cuffed). If necessary, refer to appropriate standards
of Canada, the EU member states, or U.S. OSHA.
9. PHYSICAL & CHEMICAL PROPERTIES
9.1 Appearance:
Solid, grey or silver color
9.2 Odor:
Odorless
9.3 Odor Threshold:
NA
9.4 pH:
NA
9.5 Melting Point/Freezing Point:
NA
9.6 Initial Boiling Point/Boiling
Range:
NA
9.7 Flashpoint:
NA
9.8 Upper/Lower Flammability
Limits:
NA
9.9 Vapor Pressure:
NA
9.10 Vapor Density:
NA
9.11 Relative Density:
NA
9.12 Solubility:
Insoluble
9.13 Partition Coefficient (log P
ow
):
NA
9.14 Autoignition Temperature:
NA
9.15 Decomposition Temperature:
NA
9.16 Viscosity:
NA
9.17 Other Information:
NA
10. STABILITY & REACTIVITY
10.1 Stability:
Stable under normal conditions of use (See Section 7).
10.2 Hazardous Decomposition
Products:
Irritating vapors and toxic gases (e.g., carbon monoxide and carbon dioxide).
10.3 Hazardous Polymerization:
Will not occur.
10.4 Conditions to Avoid:
Use or storage near incompatible substances.
10.5 Incompatible Substances:
Strong oxidizing agents, strong acids and bases.
11. TOXICOLOGICAL INFORMATION
11.1 Routes of Entry: Inhalation:
NO
Absorption:
YES
Ingestion:
NO
11.2 Toxicity Data:
This material or its emission may induce an allergic of sensitization reaction and thereby aggravate existing systemic
disease.
11.3 Acute Toxicity:
Overexposure to welding fumes may cause: fever, nausea, giddiness, eye irritation to the respiratory tract and to other
mucous membranes.
11.4 Chronic Toxicity:
See Section 4.5
11.5 Suspected Carcinogen:
No.
11.6 Reproductive Toxicity:
This product is not reported to cause reproductive toxicity in humans.
Mutagenicity:
This product is not reported to produce mutagenic effects in humans.
Embryotoxicity:
This product is not reported to produce embryotoxic effects in humans.
Teratogenicity:
This product is not reported to cause teratogenic effects in humans.
Reproductive Toxicity:
This product is not reported to cause reproductive effects in humans.
SAFETY DATA SHEET
Page 4 of 6
HFT-96084
Prepared to OSHA, ACC, ANSI, NOHSC, WHMIS, 2001/58 & 1272/2008/EC Standards SDS Revision: 1.1 SDS Revision Date: 7/27/2015
11. TOXICOLOGICAL INFORMATION
11.7 Irritancy of Product:
General Nuisance Dusts: Many of the metal oxides generated as components of welding fume, are considered nuisance
dusts (such as oxides of titanium and aluminum), which are essentially nontoxic and chemically nonirritating. Skin
contact has shown no problems other than possible drying and mechanical irritation. Eye contact can produce
particulate irritation. Excessive inhalation can produce mild pulmonary irritation and possible non-disabling slight fibrosis
of the lungs.
11.8 Biological Exposure Indices:
NE
11.9 Physician Recommendations:
Treat symptomatically.
12. ECOLOGICAL INFORMATION
12.1 Environmental Stability:
There are no specific data available for this product.
12.2 Effects on Plants & Animals:
There are no specific data available for this product.
12.3 Effects on Aquatic Life:
There are no specific data available for this product.
13. DISPOSAL CONSIDERATIONS
13.1 Waste Disposal:
Waste disposal must be in accordance with appropriate Federal, state, provincial and local regulations.
13.2 Special Considerations:
NA
14. TRANSPORTATION INFORMATION
The basic description (ID Number, proper shipping name, hazard class & division, packing group) is shown for each mode of transportation. Additional
descriptive information may be required by 49 CFR, IATA/ICAO, IMDG and the CTDGR.
14.1 49 CFR (GND):
NOT REGULATED
14.2 IATA (AIR):
NOT REGULATED
14.3 IMDG (OCN):
NOT REGULATED
14.4 TDGR (Canadian GND):
NOT REGULATED
14.5 ADR/RID (EU):
NOT REGULATED
14.6 SCT (MEXICO):
NOT REGULATED
14.7 ADGR (AUS):
NOT REGULATED
15. REGULATORY INFORMATION
15.1 SARA Reporting
Requirements:
This product does not contain any substances subject to SARA Title III, section 313 reporting requirements.
Aluminum
(fumes and dusts) are subject to SARA Title 313 (EPCRA).
15.2 SARA Threshold Planning
Quantity:
There are no specific Threshold Planning Quantities for the components of this product.
15.3 TSCA Inventory Status:
The components of this product are listed on the TSCA Inventory or are otherwise exempt.
15.4 CERCLA Reportable Quantity
(RQ):
NA
15.5 Other Federal Requirements:
None of the ingredients are listed as Hazardous Air Pollutants (HAPs). None of the ingredients are listed as Toxic
Pollutants under the Clean Water Act (CWA). None of the ingredients are listed as Priority Pollutants under the Clean
Water Act (CWA). This product does not contain any Class 1 or Class 2 ozone depletors.
15.6 Other Canadian Regulations:
This product has been classified according to the hazard criteria of the Controlled Products
Regulations (CPR) and the SDS contains all of the information required by the CPR. The
components of this product are listed on the DSL/NDSL. The following chemicals are listed on the
Ingredient Disclosure List: Chromium, Manganese, and Molybdenum.
WHMIS Classification: D2B (Other Toxic Effects).
15.7 State Regulatory Information:
None of the ingredients in this product, present in a concentration of 1.0% or greater, are listed on any of the following
state criteria lists: California Proposition 65 (CA65), Delaware Air Quality Management List (DE), Florida Toxic
Substances List (FL), Massachusetts Hazardous Substances List (MA), Michigan Critical Substances List (MI),
Minnesota Hazardous Substances List (MN), New Jersey Right-to-Know List (NJ), New York Hazardous Substances List
(NY), Pennsylvania Right-to-Know List (PA), Washington Permissible Exposures List (WA), Wisconsin Hazardous
Substances List (WI).
15.8 Other Requirements:
The primary components of this product are not listed in Annex I of EU Directive 67/548/EEC:
Harmful (Xn). Risk Phrases
(R): 9 - Use only in well ventilated areas. Safety Phrases (S): 22-
36/37/39-38-51 - Do not breathe fumes. Wear suitable protective clothing, gloves and eye/face
protection. In case of insufficient ventilation wear suitable respiratory equipment. Use only in well-
ventilated areas.
SAFETY DATA SHEET
Page 5 of 6
HFT-96084
Prepared to OSHA, ACC, ANSI, NOHSC, WHMIS, 2001/58 & 1272/2008/EC Standards SDS Revision: 1.1 SDS Revision Date: 7/27/2015
16. OTHER INFORMATION
16.1 Other Information:
DANGER! FLAMMABLE SOLID. MAY CAUSE AN ALLERGIC SKIN REACTION. CAUSES SERIOUS EYE
IRRITATION. MAY BE HARMFUL IF INHALED. Keep away from heat, hot surfaces, sparks, open flames and other
ignition sources. No smoking. Avoid breathing dust. Wash thoroughly after handling. Wear protective gloves/eye
protection/face protection. IF INHALED: Call a POISON CENTER/doctor if you feel unwell. IF ON SKIN: Wash with
soap and water. If skin irritation occurs: Get medical advice/attention. IF IN EYES: Rinse immediately with water for
several minutes. Remove contact lenses if present and easy to do. Continue rinsing. P370+P378 – In case of fire: Use
Dry sand or salt (NaCl), class D dry-powder extinguisher. DO NOT USE water, CO
2
-extinguisher and halogenated
agents. Dispose of contents/container to a licensed treatment, storage or disposal facility (TSDF). KEEP LOCKED UP
AND OUT OF REACH OF CHILDREN.
16.2 Terms & Definitions:
See last page of this Safety Data Sheet.
16.3 Disclaimer:
This Safety Data Sheet is offered pursuant to OSHA’s Hazard Communication Standard, 29 CFR §1910.1200. Other
government regulations must be reviewed for applicability to this product. To the best of ShipMate's & Harbor Freight
Tools USA, Inc.’s knowledge, the information contained herein is reliable and accurate as of this date; however,
accuracy, suitability or completeness is not guaranteed and no warranties of any type, either expressed or implied, are
provided. The information contained herein relates only to the specific product(s). If this product(s) is combined with
other materials, all component properties must be considered. Data may be changed from time to time. Be sure to
consult the latest edition.
16.4 Prepared for:
Harbor Freight Tools USA, Inc.
26541 Agoura Road
Calabasas, CA 91302 USA
Tel: +1 (805) 388-1000
http://www.harborfreight.com/
16.5 Prepared by:
ShipMate, Inc.
P.O. Box 787
Sisters, Oregon 97759-0787 USA
Tel: +1 (310) 370-3600
Fax: +1 (310) 370-5700
http://www.shipmate.com
SAFETY DATA SHEET
Page 6 of 6
HFT-96084
Prepared to OSHA, ACC, ANSI, NOHSC, WHMIS, 2001/58 & 1272/2008/EC Standards SDS Revision: 1.1 SDS Revision Date: 7/27/2015
DEFINITION OF TERMS
A large number of abbreviations and acronyms appear on a SDS. Some of these that are commonly used include the following:
GENERAL INFORMATION:
CAS No. Chemical Abstract Service Number
EXPOSURE LIMITS IN AIR:
ACGIH American Conference on Governmental Industrial Hygienists
C Ceiling Limit
ES Exposure Standard (Australia)
IDLH Immediately Dangerous to Life and Health
OSH
A
U.S. Occupational Safety and Health Administration
PEL Permissible Exposure Limit
STEL Short-Term Exposure Limit
TLV Threshold Limit Value
TW
A
Time Weighted Average
FIRST AID MEASURES:
CPR Cardiopulmonary resuscitation - method in which a person whose heart has
stopped receives manual chest compressions and breathing to circulate blood
and provide oxygen to the body.
HMIS-III HEALTH, FLAMMABILITY & REACTIVITY RATINGS:
0 Minimal Hazard
HEALTH
1 Slight Hazard
FLAMMABILITY
2 Moderate Hazard
PHYSICAL HAZARDS
3 Severe Hazard
PERSONAL PROTECTION
4 Extreme Hazard
PERSONAL PROTECTION RATINGS:
A
G
B
H
C
I
D
J
E
K
F
X
Consult your supervisor or SOPs fo
r
special handling directions.
Safety Glasses
Splash Goggles
Face Shield &
Protective Eyewear
Gloves
Boots
Synthetic Apron
Protective Clothing
& Full Suit
Dust Respirator
Full Face Respirator
Dust & Vapor Half-
Mask Respirator
Full Face
Respirator
Airline Hood/Mask
or SCBA
OTHER STANDARD ABBREVIATIONS:
ML Maximum Limit
mg/m3 milligrams per cubic meter
N
A
Not Available
ND Not Determined
NE Not Established
NF Not Found
NR No Results
ppm parts per million
SCB
A
Self-Contained Breathing Apparatus
NATIONAL FIRE PROTECTION ASSOCIATION: NFPA
FLAMMABILITY LIMITS IN AIR:
Autoignition
Temperature
Minimum temperature required to initiate combustion in air with no other
source of ignition
LEL Lower Explosive Limit - lowest percent of vapor in air, by volume, that will
explode or ignite in the presence of an ignition source
UEL Upper Explosive Limit - highest percent of vapor in air, by volume, that will
explode or ignite in the presence of an ignition source
HAZARD RATINGS:
0 Minimal Hazard
1 Slight Hazard
2 Moderate Hazard
3 Severe Hazard
4 Extreme Hazard
ACD Acidic
ALK Alkaline
COR Corrosive
W Use No Water
OX Oxidizer
TREFOIL Radioactive
TOXICOLOGICAL INFORMATION:
LD
50
Lethal Dose (solids & liquids) which kills 50% of the exposed animals
LC
50
Lethal concentration (gases) which kills 50% of the exposed animal
ppm Concentration expressed in parts of material per million parts
TD
lo
Lowest dose to cause a symptom
TCLo Lowest concentration to cause a symptom
TD
lo
, LD
lo
, & LD
o
or
TC, TC
o
, LC
lo
, & LC
o
Lowest dose (or concentration) to cause lethal or toxic effects
IARC International Agency for Research on Cancer
NTP National Toxicology Program
RTECS Registry of Toxic Effects of Chemical Substances
BCF Bioconcentration Factor
TL
m
Median threshold limit
log
K
OW
or log
K
OC
Coefficient of Oil/Water Distribution
REGULATORY INFORMATION:
WHMIS Canadian Workplace Hazardous Material Information System
DOT U.S. Department of Transportation
TC Transport Canada
EP
A
U.S. Environmental Protection Agency
DSL Canadian Domestic Substance List
NOHSC National Occupational Health and Safety Commission (Australia)
NDSL Canadian Non-Domestic Substance List
PSL Canadian Priority Substances List
TSC
A
U.S. Toxic Substance Control Act
EU European Union (European Union Directive 67/548/EEC)
WG
K
Wassergefährdungsklassen (German Water Hazard Class)
HMIS-III National Paint & Coatings Association Hazardous Materials Identification System
WORKPLACE HAZARDOUS MATERIALS IDENTIFICATION (WHMIS) SYSTEM:
Class A Class B Class C Class D1 Class D2 Class D3 Class E Class F
Compressed Flammable Oxidizing Toxic Irritation Infectious Corrosive Reactive
EC (67/548/EEC) INFORMATION:
C E F N O T Xi Xn
Corrosive Explosive Flammable Harmful Oxidizing Toxic Irritant Harmful
CLP/GHS (1272/2008/EC) PICTOGRAMS:
GHS01 GHS02 GHS03 GHS04 GHS05 GHS06 GHS07 GHS08 GHS09
Explosive Flammable Oxidizer Pressurized Corrosive Toxic
Harmful
Irritating
Health
Hazard
Environ-
ment
