Battery Life（电池寿命）
Battery Replacement（电池更换）
Name（名称） External Tire Pressure Sensor（BLE）/外置胎压传感器（蓝牙版）
1year/1 年
MPack0580
CR 1632
22.5 x 15 mm
0.01 Bar
0-8 Bar
Size Parameters（尺寸参数）
Measurement Accuracy（测量精度）
Pressure Measurement Range
（压力测量范围）
Product Overview（产品概述）
Package Contents（产品清单）
Product Installation（产品安装）
Product Specifications（产品规格）
Install the tire pressure sensor onto the tire valve to complete the installation. Once connected to the onboard display
unit, the tire pressure and tire temperature will be shown in real time, helping ensure safer driving.
将胎压传感器安装在轮胎阀上，即可完成安装。通过与车机连接，轮胎气压和轮胎温度实时显示车机上，有助于安全行驶。
External Sensors ×2
外置传感器 ×2
Anti-theft Nuts ×2
防盗螺母 ×2
Wrench ×1
扳手 ×1
① Remove the valve caps from the front and rear wheels,
then screw the included anti-theft nuts onto the front
and rear tire valves.
将前后轮气嘴帽拆出，并将胎压传感器附赠防盗螺
母分别拧入前后轮气门。
进入胎压应用页，点击配对按钮进行配对。
② Open the tire pressure app and tap the Pair button
to start pairing.
当前轮数据窗口闪烁时，将任意一个胎压传感器拧入前轮气嘴，视窗出现数值即完成配对，并用附赠扳手逆时针拧
紧防盗螺母固定；当后轮数据窗口闪烁时，再将另一传感器拧入后轮气嘴，出现数值即完成配对。
③ When the front wheel data window flashes, screw any one of the tire pressure sensors onto the front valve.
Once a value appears on the display, pairing is complete—then use the included wrench to tighten the anti-theft
nut counterclockwise. When the rear wheel data window flashes, screw the other sensor onto the rear valve;
once a value appears, pairing is complete.
配对前请勿提前将传感器拧入气门嘴。
安装完成后请检查是否存在漏气情况。
传感器发射信号的逻辑为当感受到压力变化或、车辆车轮转动，配对时可能存在压力检测非实际压力的情况，以
30KM/H以上时速骑行一段距离即可读取准确胎压。
配对前传感器不区分，配对后需要区分前后轮，如重新进行配对无需区分前后轮。
4.Please check for air leaks after installation.
3.There may be situations where pressure detection does not accuratelyreflect the actual pressure when paired.
Accurate tire pressure readingscan be obtained by riding a certain distance at a speed of 30 km/h orabove.
2.Before pairing, the sensors do not need to distinguish front from rearwheels; After pairing, the sensors need to
distinguish front from rearwheels;If you pair again, the sensors do not need to distinguish frontfrom rear wheels.
1.Do not screw the sensor into the valve before pairing.
Tips（注意事项）
外置胎压传感器（蓝牙版）外置胎压传感器（蓝牙版）
使用说明书使用说明书
External Tire Pressure Sensor（BLE）
User Instruction
xxxxx
xxxxx
xxxxx
xxxxx
xx
xxxxx
xxxxx
xxxxx
xxxxx
xx
FCC Warnning:
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable
protection againstharmful interference in a residential installation. This equipment generates,
uses and can radiateradio
frequency
energy
and,
if
not
installed
and
used
in
accordance
with
the
instructions,
maycause
harmful
interference
to
radio
communications.
However,
there
is
no
guarantee
thatinterference
will
not
occur
in
a
particular
installation.
If
this
equipment
does
cause
harmfulinterference to radio or television reception, which can be
determined by turning the equipmentoff
and
on,
the
user
is
encouraged
to
try
to
correct
the
interference
by
one
or
more
of
thefollowing measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution:
Any
changes
or
modifications
to
this
device
not
explicitly
approved
by
manufacturer
could void your authority to operate this equipment.
This
device
complies
with
part
15
of
the
FCC
Rules.
Operation
is
subject
to
the
following
two
conditions:
(1)This
device
may
not
cause
harmful
interference,
and
(2)
this
device
must
accept
any
interference received, including interference that may cause undesired operation.
This
equipment
complies
with
FCC
radiation
exposure
limits
set
forth
for
an
uncontrolled
environment.
This
equipment
should
be
installed
and
operated
with
minimum
distance
20cm
between the radiator and your body.
