SSI 8400BZ
EN
STEAM IRON
Translation of the original manual
SSI 8400BZ
A
1
5
2 3 4
6
7
8
- 1 -
07/2024
2024, .
EN Steam Iron
Important Safety Instructions
READ CAREFULLY AND STORE FOR FUTURE USE.
• This appliance may be only used by children aged
8years and older and by persons with physical, sensory
or mental impairments or lack of experience and
knowledge, if they are supervised or have been instructed
on the safe use of the appliance and understand the
potential hazards.
• Children must not play with the appliance. Cleaning and
maintenance must not be performed by children without
supervision.
• If the power cable is damaged, have it replaced in
aprofessional service centre in order to prevent
adangerous situation. It is forbidden to use the appliance
with the power cable damaged.
• The iron must not be left unattended when connected to
apower socket.
• The plug must be pulled out of the socket before filling the
water tank.
• The filling hole must not be opened during use.
• The iron must be used and used and placed on aflat and
stable surface.
• When placing the iron on the stand, ensure that the
surface on which the stand is located is stable.
STEAM IRON
- 2 -
07/2024
2024, .
• The iron must not be used if it has fallen, if there are visible
signs of damage, or if it leaks.
• Do not leave the iron and its power supply within reach
of children under 8 years of age when it is powered or
cooling.
CAUTION: Hot surface
Surfaces may become hot during use.
• Before connecting the base to the power socket, ensure that the voltage indicated on its rating plate matches the voltage in the socket.
• Connect the base only to aproperly grounded socket. Do not use an extension cord.
• Do not touch the iron with wet or moist hands when connected to the power socket.
• To prevent the risk of electric shock, do not wash the iron or base under running water, spray it with water, or immerse it in water or any other liquid.
• Ensure that the power cable does not come into contact with water, moisture or aheated surface.
• Do not place heavy objects on the power cable. Make sure that the power cable does not hang over the edge of the table or touch hot surfaces or
sharp objects.
• Disconnect the base from the power socket by pulling the plug of the power cable, not the cable itself. Otherwise, damage to the power cable or the
socket may occur.
• Do not pull or carry the base by the power cable. Do not pull the iron by the iron cable.
• To avoid the risk of electric shock, do not repair the iron or base yourself or modify them in any way. All repairs should be carried out by an
authorised service centre. By interfering with the product, you risk losing the legal right to defective performance or warranty for quality.
• If the iron cable is damaged, have it replaced at aspecialised service centre. It is forbidden to use the iron with adamaged cable.
• The iron is intended for household use. Do not use it in an industrial environment or outdoors.
• Do not place the iron on or near an electric or gas stove or other sources of heat.
• Never iron clothes while wearing them.
• Do not touch the hot soleplate. Otherwise, burns may occur.
• Ironed clothes may be hot immediately after removing the iron. Take extra care to avoid burns.
• Never fill the water tank directly under the tap. Always use asuitable container for filling the tank. Do not add vinegar, descalers, or other additives to
the tank.
• Before cleaning or any other handling of the iron and the base that you have disconnected from the power socket, allow the soleplate to cool down.
- 3 -
07/2024
2024, .
• Thank you for purchasing our SENCOR product; we hope it will serve
to your satisfaction.
• Before using this appliance, please familiarise yourself with the user
manual, even if you are already familiar with using similar types of
appliances. Use the appliance only as described in this user manual.
Keep the manual for future reference.
• It is recommended to keep the original packaging, packing material,
receipt and confirmation of the extent of the seller'sliability or warranty
certificate at least for the duration of the legal right of defective
performance or quality guarantee. When transporting the appliance,
we recommend packaging it again in the original box provided by the
manufacturer.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DESCRIPTION OF THE IRON
A1 Soleplate
A2 Control panel
A3 Steam boost button
A4 Handle
A5 Water tank
A6 Iron body
A7 Power cord
A8 Water tank lid
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PURPOSE OF USE
The iron is intended for ironing clothes, fabrics, or materials specifically
designed for ironing. Refer to the information label on the clothes, fabric
or material.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BEFORE FIRST USE
• Before first use, remove the appliance and its accessories form the
packaging and discard all promotional labels and tags. Check that
neither the appliance nor any of its components is damaged.
• Wipe the soleplate of the iron with alightly damp cloth and then dry
it. Also, wipe the outer parts of the iron with adry or lightly damp cloth
and dry them thoroughly.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PREPARATION FOR USE
Filling the Water Tank
Warning:
Always ensure that the iron is switched off and the
power cable is disconnected from the power socket
before filling the tank.
We recommend using only distilled or demineralised
water.
1. Open the water tank lid and tilt the iron slightly.
2. Pour clean cold water through the hole in the tank. Wipe any spilled
water with adry cloth.
3. Close the lid. Press gently until you hear aclick.
Use afilling measuring cup when filling the tank. Do not fill the water tank
directly from the tap.
Do not overfill the tank. Always fill to the MAX mark indicated on the tank
during filling.
Warning:
Never fill the tank with hot or boiling water, service
water or any other liquid. Do not add water softener,
vinegar, starch, descaling agent, perfume mixes, or
other additives.
First Use of the Iron
• Before the first use of the iron, we recommend ironing asmall damp
cloth or towel with the iron at ahigh temperature to remove any
possible residues on the soleplate.
• You may notice astrange smell during the first use. This is anormal
occurrence. It disappears with use.
• During the first use of the iron, small particles or impurities may come
out of the holes on the soleplate. Do not be surprised or disturbed by
this. This does not affect the proper functioning of the steam generator.
Note:
During the heating process of the soleplate, asmall amount
of water may flow from the soleplate. This is anormal
occurrence.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
USING THE IRON
Connecting to aPower Source
Place the iron upright on the ironing board or surface where you will be
ironing.
Unwind the power cord completely andplug the power cord plug into
aproperly grounded power socket.
Switching on the Iron
The iron automatically switches on when the plug is connected to the
power socket. The power-on light will flash to indicate that the iron is
heating up. When the light comes on, the iron is ready to use at the
selected temperature.
Steam Control Modes
Thanks to Smart manager technology, you will be able to iron in two
different ways in terms of steam control: the AUTO mode and the PRO
mode.
Press and hold both buttons at the same time until the light for AUTO
mode or PRO mode comes on.
1. Pro Mode
In this mode, the iron does not release steam continuously. It only
releases steam when the steam button under the handle is pressed
continuously. When you release the button, the steam release stops.
Fabric Type
Ironing
Surface
Temperature
Steam
Boost
Continuous
Steam
Release
Linen 230°C 5 0
Cotton 220°C 4 0
Jeans 210°C 3 0
Children'slaundry 200°C 1 0
Wool 170°C 3 0
Antistatic fabrics (polyester) 150°C 2 0
Silk and fine fabrics 140°C 2 0
Synthetics 130°C 1 0
Other fabrics 130°C 3 0
2. AUTO Mode
In this mode, the iron produces steam continuously. Press the steam
button once briefly to start production, press it again briefly to stop.
Continuous steam is only produced when you move the iron.
Fabric Type
Ironing
Surface
Temperature
Steam
Boost
Continuous
Steam
Release
Linen 230°C 0 2
Cotton 220°C 0 1
Jeans 210°C 0 1
Children'slaundry 200°C 0 1
Wool 170°C 0 2
EN
Steam Iron
User Manual
- 4 -
07/2024
2024, .
Fabric Type
Ironing
Surface
Temperature
Steam
Boost
Continuous
Steam
Release
Antistatic fabrics (polyester) 150°C 0 1
Silk and fine fabrics 140°C 0 1
Synthetics 130°C 0 1
Other fabrics 130°C 0 2
Warning:
HOT SURFACE AND HOT STEAM!
Be especially careful when ironing andhandling the
iron. The soleplate and the steam temperature are
very hot. Serious injury and burns can occur with
improper handling.
Never touch the soleplate with your hands! Do not
steam clothes directly on yourself or on others!
Warning:
Never leave the iron on unattended. Pay extra
attention if children are near the iron, even when it is
switched off.
Temperature and Steam Settings
When setting the temperature, pay attention to the fabric'scomposition.
We recommend that you sort your laundry according to the
international symbols on the textile, the type of fabric or the
manufacturer'srecommendations on the tag. The number of dots inside
the international symbol corresponds to the number of dots on the rotary
temperature controller.
The iron will switch on at alow temperature when the power cord is
plugged in. The indicator will flash red. Press the temperature setting
button repeatedly to set the temperature:
Symbol
Temperature
Setting
Fabric Type
Low temperature
Synthetic fabric (acrylic, acetate,
polyester, viscose, etc.)
Medium
temperature
Cotton withan admixture of other
types of fibres, silk, wool, wool withan
admixture of other types of fibres, etc.
High temperature Corduroy, cotton, denim andlinen
Ironing without Steam
If you iron using the dry ironing method, do not fill the water tank. Leave
it empty.
Plug the power cord into the power socket and place the iron in avertical
position on the ironing board or on the surface where you will be ironing.
Set the desired temperature. The temperature indicator will flash red. This
indicates that the iron is heating up.
When the indicator stops flashing and lights up, the iron is warm and
ready to use.
The indicator may start to flash during ironing. This indicates that the
iron is heating up to the set temperature. Wait until it stops flashing and
lights up.
When you have finished ironing, remove the power cord plug from the
power socket and allow the iron to cool in asafe place.
Ironing withSteam
Before ironing withsteam, it is necessary to refill the water tank. Follow
the instructions inthe “Filling the Tank” section.
Plug the power cord into the power socket and place the iron in avertical
position on the ironing board or on the surface where you will be ironing.
Set the desired temperature. The temperature indicator will flash red. This
indicates that the iron is heating up.
When the indicator stops flashing and lights up, the iron is warm and
ready to use.
Use the steam release control to set the desired steam release mode.
The indicator may start to flash during ironing. This indicates that the
iron is heating up to the set temperature. Wait until it stops flashing and
lights up.
When you have finished ironing, remove the power cord plug from the
power socket and allow the iron to cool in asafe place.
Steam Boost
The steam boost releases alarger amount of steam at themaximum
temperature. Use this function for heavily wrinkled fabrics or garments
where you need to loosen fibres for easier ironing.
Press the steam boost button to activate it.
Vertical Ironing
The iron can also be used for vertical ironing of curtains, net curtains and
clothes that are hung on ahanger.
Warning:
Never use an iron to iron clothes that people have on.
Select the temperature according to the type of fabric you will be ironing.
Grasp the iron by the handle and hold it against the garment or curtain.
Iron it by moving the iron from top to bottom.
Putting the Iron down during Ironing
Place the iron in avertical position on the heat-insulated surface of the
ironing board during ironing, or in asafe place on the ironing surface.
Switching off the Iron
When you have finished ironing, place the iron in avertical position and
unplug the power cord from the power socket. Allow the iron to cool
before cleaning.
Automatic Switch-off
The automatic switch-off function switches off the heating element of the
iron if it remains motionless for afew moments.
The indicator will flash and several beeps will sound, indicating that the
iron has been automatically switched off, and in the following situations:
• The iron is in ahorizontal position without moving for more than 30
seconds.
• The iron is turned on its side without moving for more than 30
seconds.
• The iron is in the vertical position for more than 8 minutes.
To cancel the automatic switch-off function and allow the iron to heat up
again, lift or move the iron slightly. The temperature indicator will flash
red. When the indicator stops flashing and lights up, the iron is warm and
ready to use.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ANTI-CALC SYSTEM
The iron is equipped with apermanent Anti-Calc filter that reduces
the formation of calcium deposits inside the iron. This filter cannot be
removed. The effectiveness of the filter depends on the hardness of the
water you use.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IRONING TIPS AND TRICKS
• Follow the care instructions foreach garment. Iron only solid-coloured
andheat-resistant fabrics. We recommend ironing theprinted clothes
inside out.
• Sort the clothes by temperature from low to high. Start ironing items at
alow temperature and gradually increase it, as the iron heats up faster
than it cools down.
• Never iron over areas with sweat stains or other stains. High heat will
set the stain making it difficult to remove.
• To prevent silk, wool, and synthetic fabrics from becoming shiny after
ironing, iron them inside out.
• Some materials are easier to iron when lightly damp.
• For fine fabrics, sprinkle water or iron over aslightly damp cloth. You
can also hold the iron about 2 cm above the fabric.
• Iron heavily wrinkled garments at ahigh temperature with steam and
use the steam boost function to loosen and straighten the fabric fibres.
• Avoid ironing zips, studs or other decorative parts of clothing. This
could damage the soleplate.
- 5 -
07/2024
2024, .
• To prevent wrinkling, select an appropriate spin speed when washing
and hang the laundry correctly on the clothesline or rack. Hang some
items of clothing, such as shirts, on hangers. Dry sweaters, cardigans
and other items spread out on aflat surface.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CLEANING AND MAINTENANCE
Before cleaning the iron, unplug the power cord from the power socket
and allow the appliance to cool completely.
Do not use abrasive cleaning agents, solvents, or any substances to clean
any parts of the appliance that could damage the surface of the appliance.
Warning:
To prevent the risk of electric shock, do not immerse
the appliance, power cable, or plug into water or any
other liquid.
Cleaning the Iron
Wipe the soleplate of the iron with alightly damp cloth and then dry it.
Also, wipe the outer parts of the iron with adry or lightly damp cloth and
dry them thoroughly.
Removing Mineral Deposits
The self-cleaning function is used to remove mineral deposits. Use this
function regularly according to water hardness and frequency of use. If
the water in your area is very hard (i.e. flakes come off the ironing surface
during ironing), you should use the self-cleaning function more often.
1. Fill the water tank to the MAX level.
2. Insert the plug to the socket.
3. Set the temperature control button to the self-cleaning function.
4. Gently shake the iron until all water in thetank is used up.
5. If the water coming out of the iron still contains limescale particles,
repeat the self-cleaning process.
Storage
• If you are not going to use the iron, switch it off, unplug it from the
power socket and leave it to cool down completely.
• Empty the water tank. Wind the iron cord in front of the side surface so
that the cord does not touch the heated ironing surface.
• Store the iron in adry, clean and well-ventilated place where it will not
be exposed to extreme temperatures and where it will be out of reach
of children or pets.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TECHNICAL SPECIFICATIONS
Rated voltage range ..............................................................................220−240 V~
Rated frequency ..........................................................................................50–60 Hz
Rated power input .............................................................................2400–2800 W
Water tank capacity ......................................................................................... 330 ml
Continuous steam output ............................................................................55 g/min
Steam boost ...................................................................................................195 g/min
We reserve the right to change the text and technical specifications.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INSTRUCTIONS AND INFORMATION ON DISPOSAL OF USED
PACKAGING MATERIAL
Dispose of used packaging material in the designated waste disposal area
determined by the municipality.
DISPOSAL OF USED ELECTRICAL AND ELECTRONIC EQUIPMENT
This symbol on the products or accompanying documents
indicates that used electrical and electronic products
should not be disposed of with regular municipal waste.
For proper disposal and recycling of these products, deliver
them to designated collection points. Alternatively, in some
European Union states or other European countries the
products can be returned to the local retailer when buying
an equivalent new product. By properly disposing of this
product, you help preserve valuable natural resources and contribute to
preventing potential negative impacts on the environment and human
health resulting from improper waste disposal. For further details, contact
your local authorities or the nearest collection point. Fines may be
imposed for improper disposal of this type of waste in accordance with
national regulations.
For Business Entities in European Union States
If you want to dispose of electric or electronic devices, ask your retailer or
supplier for the necessary information.
Disposal in Other Countries Outside the European Union
This symbol is valid in the European Union. To dispose of this product
elsewhere, request necessary information on the correct disposal method
from local authorities or your retailer.
This product complies with all the essential requirements of
the applicable EU directives.
