User’s Guide
MODEL
www.impecca.com
Window Air Conditioner
TABLE OF CONTENTS
WELCOME 3
IMPORTANT SAFETY INSTRUCTIONS 3
ELECTRICAL REQUIREMENTS 5
PACKING LIST 7
INSTALLATION & ASSEMBLY INSTRUCTIONS 8
HOW TO INSTALL 10
USING YOUR AIR CONDITIONER 15
ELECTRONIC CONTROL PANEL 16
REMOTE CONTROL 19
CARE AND CLEANING 21
TROUBLESHOOTING 22
CUSTOMER SUPPORT 24
ONE-YEAR LIMITED APPLIANCE WARRANTY (US) 25
2
ENGLISH
WELCOME
Thank you for purchasing this Window Air Conditioner Before operating this unit, please
read these instructions completely and keep the manual ready for further reference
IMPORTANT SAFETY INSTRUCTIONS
Before installing and using your air conditioner, please read this owner's manual
carefully Store thismanual in a safe place for future reference Your safety and the safety
of others is very important to us Please pay attention to all safety messages outlined in
this user manual
WARNING
To reduce the risk of fire, electrical shock or injury when using your air
conditioner, follow the basic precautions below:
• Plug into a grounded 3 prong outlet
• Do not remove the ground prong
• Do not use a plug adapter
• Do not use an extension cord
• Unplug the air conditioner before servicing
• Use two or more people to move and install the air conditioner
This is a safety alert symbol This symbol alerts you to potential hazards
that can harm you or others or even cause death All safety messages
will directly follow the safety alert symbol and/or the words "DANGER"
or "WARNING"
DANGER
Failure to immediately follow these instructions may cause serious injury or
even death
WARNING
All Safety messages alert you of potential hazards, how to reduce the chance of
injury, and what can happen if instructions are not followed correctly
3
ENGLISH
INTRODUCTION TO REFRIGERANTS R32
The refrigerants used for air conditioners are environmentally friendly hydrocarbons
R32 This kind of erant is combustible and odorless Moreover, it can burn and explode
under certain condition However, there will be no risk of burning and explosion if
you comply with the following table to install your air conditioner in a room with an
appropriate area and use it correctly
Compared with ordinary refrigerants, Refrigerant R32 is environmentally friendly and
do not destroy the ozone sphere and that its value of greenhouse eect is also very low
WARNING
• Please read the manual before installation, using, maintenance
• Do not use means to accelerate the defrosting process or to clean, other than those
recommended by the manufacturer
• Do not pierce or burn the appliance
• The appliance shall be stored in a room without continuously operating sources
(for example: open flames, an operating ignition gas appliance or an operating
electric heater )
• Please contact the nearest aer-sale service center when maintenance is necessary
At the time of maintenance, the maintenance personnel must strictly comply with
the Operation Manual provided by the corresponding manufacturer and any
nonprofessional is prohibited to maintain the air conditioner
• The handling, installation, storage, servicing and disposal must comply with the
provisions of gas-related national laws and regulations, and also national wiring
regulation
• It is necessary to clear away the refrigerant in the system when maintaining or
scrapping an air conditioner Be aware that refrigerants may not contain an odour
• This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or supervision or instruction concerning
use of the appliance by a person responsible for their safety
• Children should be supervised to ensure that they do not play with the appliance
• Unit operation limits: Outdoor side 61~110°F, 80%RH, indoor side 61~90°F, 80%RH
4
ENGLISH
ELECTRICAL REQUIREMENTS
WARNING
ELECTRICAL SHOCK
• Hazard Plug into a grounded 3 prong outlet
• Do not remove the ground prong
• Do not use an adapter
• Do not use an extension cord
• Failure to follow these instructions can result in death, fire, or electrical shock
The electrical ratings for your air conditioner are listed on the model and serial number
label located on the front le side of the unit (when facing the front) Specific electrical
requirements are listed in the chart below Follow the requirements below for the type
of plug on the power supply cord
Wiring Requirements Power Supply Cord
115 volt (103min —127max)
(6K-8K) 0-8 amps / (10K-14K) 0-12 amps
(6K-8K)10-amp time-delay fuse or circuit
breaker
(10K-14K) 15-amp time-delay fuse or
circuit breaker
Use on single outlet circuit only
RECOMMENDED GROUND METHOD
For your personal safety, this air conditioner must be grounded This air conditioner
is equipped with a 3 prong power supply cord with a grounded plug To minimize
the possibility of electrical shock, the cord must be plugged into a 3 prong outlet and
grounded in accordance with all local codes and ordinances If a 3 prong outlet is not
available, it is the customer's responsibility to have a properly grounded 3 prong outlet
installed by a qualified electrician
IT IS THE CUSTOMER'S RESPONSIBILITY:
• To contact a qualified electrician
• To assure that the electrical installation is adequate and in conformance with the
National Electrical Code, ANSI/NFPA 70-latest edition, and all local codes and
ordinances
5
ENGLISH
LCDI POWER CORD AND PLUG
This air conditioner is equipped with an LCDI (Leakage Current Detection and
Interruption) power cord that is requiredby UL This power supply cord contains state-
of-the-art electronics that sense leakage current If the cord is damaged and leakage
occurs, power will be disconnected from the unit
The LCDI power cord and plug will remove the supply source via electrical disconnect
(circuit trip) if the nominal current leakage between the cord shield and either load
conductor exceeds a predetermined value The cord will remain deenergized until the
device has been manually reset This is intended to reduce the risk of a fire in the power
cord or combustible materials nearby The cord shields are not grounded and they must
be considered a shock hazards if exposed The cord shield must not be connected to
ground or to any exposed metal
The test and reset buttons on the LCDI Plug are used to check if the plug is functioning
properly
TO TEST THE PLUG:
• Plug power cord into a wall outlet
• Press the TEST Button, the circuit should trip and cut all power to
the air conditioner
• Press the RESET button for use
If a test is performed and the indicator light remains ON, the current
leakage has been detected Do not use the air conditioner or attempt
to reset the LCDI Plug Contact Customer Service for troubleshooting
recommendations
SAVE THESE
INSTRUCTIONS
6
ENGLISH
PACKING LIST
1. Window Air Conditioner (1)
2. Remote Control (1)
3. Remote Control Battery *2
4. Top Rail (With sponge) (1)
5. Sash Lock (Two holes) (1)
6. Filler Panels (2)
(With "Le" & "Right" remark on
the front face)
7. Window Sash Seal (Sponge) (1)
8. Lock Frame (2)
9. Foam Top Window Gasket (1)
(Thin sponge for back-up use )
10. Insulation Strip (Sponge) *2
(Only for E-star model)
11. 3/8" Screws (4)
12. 1/2" Screws (3)
13. 3/4" Screws (4)
❶
❿
❾
❽
❼
❻
❺
❹
❸
❷
⓭⓬⓫
7
ENGLISH
INSTALLATION & ASSEMBLY INSTRUCTIONS
Some assembly is required for your new air conditioner Please read and follow these
instructions carefully
• This air conditioner is designed to be installed in a standard double-hung
window with a window width between 23" and 36" (584mm-914 mm) for
8000btu~10000btu, or a window width between 26" and 36" (660mm-914 mm) for
12000btu~14000btu
• The air conditioner can be installed without the accordion panels to fit in a narrow
window opening See the window dimensions
• The Lower Sash (the lower part of the window that moves up and down) must
allow for 14 5" of vertical dearance when open, for 8000btu~10000btu (See Fig 1),
or for 16" of vertical dearance when open, for 12000btu~14 000btu (See Fig 1)
• All supporting parts must be secured to firm wood, masonry, or metal
• The electrical outlet must be within reach of the power cord
• The air conditioner should be tilted about 3° for better drainage of condensate and
rainwater
NOTE:Save the product packaging and installation instructions for future reference
Store the air conditioner in the product box when not in use for an extended period of
time
8
ENGLISH
Top Rail Assembly (Optional)
The top rail must be assembled prior to installing the air conditioner in the window
Tools Needed: Phillips Head Screw Driver
Attaching the Top Rail to the Air Conditioner
• Remove the air conditioner from the box and place on a hard and flat surface
• Remove top rail from the top of the packaging material as shown in Fig A
• Align the hole in the top rail with those in the top of the unit as shown in Fig B
• Secure the top rail to the unit with the 3/8" screws as shown in Fig C
CAUTION
When handling the unit, be careful to avoid cuts from the sharp metal edges
and aluminum fins on the front and rear coils
Top Rail (With sponge) *1
3/8"Screws *4
NOTE: For safety reasons, all 4 screws must be used to attach the top rail
9
ENGLISH
HOW TO INSTALL
NOTE: Top Rail and Sliding Panels at each side are oset to provide the proper pitch
to the rear of (5/16") This is necessary for proper condensed water utilization and
drainage If you are not using the Side Panels forany reason, this pitch to the rear must
be maintained!
1 Place unit on floor, a bench or a table There is a Le and Right Window Filler
Panelbe sure to use the proper panel for each side When installed the flange for
securing the panel in place to the window sill will be facing into the room
• Hold the Accordion Panel in one hand and gently pull back the center to free the
open end See Fig 2
• Slide the free end of the panel into the cabinet as shown in Fi 3 Slide the panel
down Be sure to leave enough space to slip the top and bottom of the frame into
the rails on the cabinet
• Once the panel has been installed on
the side of the cabinet, make sure it sits
securely inside the frame channel by
making slight adjustments Slide the top
and bottom ends of the frame into the
top and bottom rails of the cabinet See
Fig 4
• Slide the panel all the way in and repeat
on the other side
10
ENGLISH
2 Keep a firm grip on the air conditioner, carefully place the unit into the window
opening so the bottom of the air conditioner frame is against the window sill
(Fig 5) Carefully close the window behindthe top rail of the unit (Suggest to keep
a downward oblique, to let accumulated rain water to drain out, from back side of
the unit bottom )
3 Extend the side panels out against the window frame (Fig 6)
4 Place the frame lock between the frame extensions and the window sill as shown
(Fig 7) Drive 3/4" (19 mm) locking screws through the frame lock and into the sill
(Fig 8)
NOTE: To prevent window sill from splitting, drill 1/8" (3 mm) pilot holes before driving
screws
11
ENGLISH
5 Drive 1/2" (12 7mm) locking screws through frame holes into window sash (Fig 9
Fig10)
6 To secure lower sash in place, attach right angle sash lock with 3/4" (19 mm) screw
as shown (Fig 11)
7 Cut foam seal and insert in the space between the upper and lower sashes (Fig 12)
12
ENGLISH
If AC is Blocked by Storm Window
Add wood as shown in Fig 13, or remove stormwindow before air conditioner is
installed
If Storm Window Frame must remain, be sure the drain holes or slots are not caulked
or painted shut Accumulated Rain Water or Condensation must be allowed to drain
out
Removing the Air Conditioner from the Window
• Turn the air conditioner o and unplug the power cord
• Remove the sash seal from between windows, and unscrew sash lock
• Remove the screws installed through the frame and frame lock
• Close (slide) the side panels into frame
• Keeping a firm grip on air conditioner, raise the sash and carefully "rock" air
conditioner backward to drain any condensate water in base of unit Be careful not
to spill any remaining water while liing unit from window
• Store parts with the air conditioner in the box
Air Conditioner Use
Operating your air conditioner properly helps you to obtain the best possible results
This section explains proper air conditioner operation
IMPORTANT: If you turn o the air conditioner, wait at least 3 minutes before turning
it back on This prevents the air conditioner from blowing a fuse or tripping a circuit
breaker
Do not try to operate your air conditioner in the cooling mode when outside
temperature is below 65°F (18°C) The inside evaporator coil will freeze up, and the air
conditioner will not operate properly
NOTE: In the event of a power failure, your air conditioner will operate at the previous
settings when the power is restored
13
ENGLISH
Introduction to Refrigerants R32
Before installing the appliance, you must read the manual carefully to get the safety
information and notes
When filling the combustible refrigerant, any of your rude operations may cause
serious injury or injuries to human body or bodies and object or objects
A leak test must be done aer the installation is completed
It is a must to do the safety inspection before maintaining or repairing an air
conditioner using combustible refrigerant in order to ensure that the fire risk is
reduced to minimum
It is necessary to operate the machine under a controlled procedure in order to ensure
that any risk arising from the combustible gas or vapor during the operation is reduced
to minimum
Requirements for the total weight of filled refrigerant and the area of a room to be
equipped with an air conditioner
1. Site Safety: Open Flames Prohibited, Ventilation Necessary
2. Operational Safety: Mind Static Electricity, Wear Protective Clothing, No Mobile
Devices
3. Installation Safety
1) Refrigerant Leak Detector
2) Appropriate Installation Location
3) The le picture is the schematic diagram of arefrigerant leak detector
14
ENGLISH
Please note that:
• The installation site should be in a well-ventilated condition
• The sites for installing and maintaining an air conditioner using Refrigerant R32
should be free from open fire or welding, smoking, drying oven or any o ther heat
source higher than 548°C which easily produces open fire
• When installing an air conditioner, it is necessary to take appropriate anti-static
measures such as wear anti-static clothing and/or gloves
• It is necessary to choose the site convenient for installation or maintenance
wherein the air inlets and outlets of the indoor and outdoor units should be
not surrounded by obstacles or close to any heat source or combustible and/or
explosive environment
• If the indoor unit suers refrigerant leak during the installat ion, all the personnel
should go out till the refrigerant leaks completely for 15 minutes If the product is
damaged, it is a must to carry such damaged product back to the maintenance
station and it is prohibited to weld the refrigerant pipe or conduct other operations
on the user's site
• It is necessary to choose the place where the inlet and outlet air of the indoor unit
is even
• It is necessary to avoid the places where there are other electrical products, power
switch plugs and sockets, kitchen cabinet, bed, sofa and other valuables right
under the lines on two sides of the indoor unit, and also prevent mechanical
damage from occurring
USING YOUR AIR CONDITIONER
Normal Operating Sounds
• You may hear a pinging noise caused by water hitting the condenser, on rainy
days, or when the humidity is high This design feature helps remove moisture and
improve eiciency
• You may hear the thermostat click when the compressor cycles on and o
• Water will collect in the base pan during rain or days of high humidity The water
may overflow and drip from the outside part of the unit
• The fan may run even when the compressor is not on
15
ENGLISH
ELECTRONIC CONTROL PANEL
NOTE: This display always shows the room temperature in Fan Mode except when
setting the Set temperature or the Timer
NOTE: * means only available for WIFI modes, For more information, please see the
WIFI manual
1. Digital Display:
Without timer setting, the operation mode is Cooling, Dry, Fan and Auto, and the set
temperature will be displayed Time will be displayed under timer setting
2. and Button:
Use these buttons on the control panel and remote to increase or decrease the Set
Temperature or Timer
Temperature range: 61°F~88°F or 16°C~31°C
3. Power Button:
Turn the air conditioner on and o
4. Mode Button:
Press the mode button to cycle through the various modes: Cool, Dry, Fan and Auto
Cool Mode: The cooling function allows the air conditioner to cool the room and
at the same time reduces humidity Press the MODE button to activate the cooling
function To optimize this function adjust the temperature by pressing the up and
down arrows and the speed by pressing the Fan Speed button
16
ENGLISH
Dry Mode: This function reduces the humidity of the air to make the room more
comfortable Press the MODE button to set the DRY mode An automatic function of
alternating cooling cycles and air fan is activated
Fan Mode: This function only works when the airconditioner is vented Press the MODE
button to set the FAN mode With pressing the FAN SPEED button, the speed changes
in the following sequence: HIGH, MED, LOW in FAN mode The remote control also
stories the speed that was set in the previous mode of operation
Auto Mode: In AUTO mode the unit automatically chooses the mode of operation
(COOL, or FAN) In this mode the temperature is set automatically according to the
room temperature (tested by the temperature sensor which is incorporated in the
indoor unit)
5. Timer Button:
Use these buttons on the control panel and remote to set the Timer
Timer O: The timed stop is programmed by pressing TIMER button Set the rest time
by pressing the button or until the rest time displayed is to your demand
then press TIMER button again
Timer On: When the unit is o, press TIMER button at the first time, set the
temperature with pressing the button or Press TIMER button at the
second time, set the rest time with pressing the button or Press TIMER
button at the third time, confirm the setting, then the rest time to next automatical
switching-on could be read on the display of the machine
Note: It can be set to automatically turn o or on in 0 5-24 hours Each press of
the buttons will increase or decrease the timer The Timer can be set in 0 5
hours increment below 10 hours and 1 hour increment for 10 hours or above The SET
light will turn on while setting To cancel the setted function, press the TIMER button
again
6. Eco Button:
When the unit is in ECO mode, thelight will turn on In ECO mode, the unit will turn o
once the room is cooled to the user-set temperature
The unit will turn back on when the room temperature rises above the user-set
temperature Before the compressor starts, the fan motor will run for a while, then it
will stop for a while, and will repeat to provide a much more comfortable feeling and
save energy
17
ENGLISH
7. Sleep Button:
Press the SLEEP button, all of the display lights will turn o aer a while, but the Sleep
light is always on In SLEEP mode, the air conditioner will automatically adjust the
temperature and fan speed to make the room more comfortable during the night The
set temperature will automatically raise or decrease based on the room temperature
and the duration of sleep
8. Fan Speed Button:
Press the FAN SPEED button to choose the fan speed options You can choose HIGH,
MED, LOW or auto speed in COOL mode and choose HIGH, MED, LOW in FAN mode
9. Filter Button:
When the Filter Check light is o, it is not necessary to press the Filter Check button
When the Filter Check light is on, you can turn o the light by pressing the Filter Check
button Aer the fan motor works for 500 total hours, the Filter Check light will turn on
to remind the user to clean the filter
10. Directional Louvers:
Use the horizontal wheels to control horizontal airflow and the air deflectors to control
vertical airflow
Air Deflector Horizontal Wheel Air Deflector
18
ENGLISH
REMOTE CONTROL
1. POWER
Turn the air conditioner on and o
2. Cool
Press the COOL button to COOL mode
3. and
Use these buttons on the control panel and remote to increase or decrease the Set
Temperature or Timer Temperature range: 61°F ~88°F or 16°C ~31°C
4. Sleep
Press the SLEEP button, all of the display lights will turn o aer a while, but the Sleep
light is always on In SLEEP mode, the air conditioner will automatically adjust the
temperature and fan speed to make the room more comfortable during the night The
set
5. Timer
Use these buttons on the control panel and remote to set the Timer
Timer O: The timed stop is programmed by pressing TIMER button Set the rest time
by pressing the button or until the rest time displayed is to your demand
then press TIMER button again
19
ENGLISH
Timer On: When the unit is o, press TIMER button at the first time, set the
temperature with pressing the button or Press TIMER button at the
second time, set the rest time with pressing the button or Press TIMER
button at the third time, confirm the setting, then the rest time to next automatical
switching-on could be read on the display of the machine
Note: It can be set to automatically turn o or on in 0 5-24 hours Each press of
the buttons will increase or decrease the timer The Timer can be set in 0 5
hours increment below 10 hours and 1 hour increment for 10 hours or above The SET
light will turn on while setting To cancel the setted function, press the TIMER button
again
6. Auto Mode
In AUTO mode the unit automatically chooses the mode of operation (COOL, or
FAN) In this mode the temperature will be set automatically according to the room
temperature (tested by the temperature sensor which is incorporated in the indoor
unit )
7. Fan Speed
Press the FAN SPEED button to choose the fan speed options You can choose HIGH,
MED, LOW or auto speed in COOL mode and choose HIGH, MED, LOW in FAN mode
8. Display
To press the DISPLAY button, it can switch o/on all lights or LED display
9. ECO
When the unit is in ECO mode, the light will turn on In ECO mode, the unit will turn o
once the room is cooled to the user set temperature The unit will turn back on when
the room temperature rises above the user set temperature Before the compressor
starts, the fan motor will run for a while, then it will stop for a while, and will repeat to
provide a much more comfortable feeling and save energy
10. Fan Only
Press the Fan Only button to FAN ONLY mode
Battery Size: AAA-NOTE: Do not mix old and new batteries or dierent types of AAA
batteries
20
ENGLISH
CARE AND CLEANING
Air Filter Cleaning
The air filter should be checked at least once every month to se e if it needs cleaing
Trapped particles and dust can build up in the filter and may decrease airflow as well
as cause the cooling coils to accumulate frost
To clean the air filter:
• Take o the power plug, then remove the filter by sliding it out from the front right
side of the air conditioner (See Fig 15)
• Wash the filter using liquid dish soap and warm water Rinse the filter thoroughly
Gently shake the filter to remove excess water
• Let the filter dry completely before placing it into the air conditioner
• If you do not wish to wash the filter, you may vacuum the filter to remove the dust
and other particles
Cabinet Cleaning
To clean the air conditioner cabinet:
• Unplug the air conditioner to prevent shock or a fire hazard Th e cabinet and
front panel of the air conditioner may be dusted with an oilfree cloth or washed
with a cloth dampened in a solution of warm water and mild liquid soap Rinse
thoroughly with a damp cloth and wipe dry
• Never use harsh cleaners, wax or polish on the cabinet front
• Be sure to wring excess water from the cloth before wiping around the controls
Excess water in or around the controls may cause damage to the air conditioner
Winter Storage
To store the air conditioner when it is not in use for an extended period of time,
remove it carefully from the window according to the installation instructions and
cover it with plastic or place it in the original box
21
ENGLISH
TROUBLESHOOTING
Problem Possible Cause Possible Solutions
The Air Conditioner will not
start
The air conditioner is
unplugged
Make sure the air conditioner
plug is pushed completely
into the outlet
The fuse is blown/circuit
breaker is tripped
Check the house fuse/circuit
breaker box and replace the
fuse or reset the breaker
Power failure The unit will automatically re-
start when power is restored
There is a protective time
delay (approx 3 minutes)
to prevent tripping of the
compressor overload For this
reason, the unit may not start
normal cooling for 3 minutes
aer it is turned back on
The current interrupter
device is tripped
Press the RESET button
located on the power cord
plug
If the RESET button will not
stay engaged,discontinue
use of the air conditioner and
contact a qualified service
technician
The Air Conditioner does not
cool as it should
Airflow is restricted Make sure there are no
curtains, blinds, or furniture
blocking the front of the air
conditioner
The temperature control may
not be set correctly
Lower the set thermostat
temperature
The air filter is dirty Clean the filter See the
Cleaning and Care Section of
the manual
The room may be too warm Please allow time for the
room to cool down aer
turning onthe air conditioner
Cold air is escaping Check for open furnace
registers and cold air returns
The cooling coils are frozen See "Air Conditioner Freezing
Up" below
22
ENGLISH
Problem Possible Cause Possible Solutions
The Air Conditioner is
freezing up
Ice blocks the air flow and
stops the air conditioner from
cooling the room
Set the MODE dial to HIGH
FAN or HIGH COOL and set
the thermostat to a higher
temperature
The Remote Control is not
working
The batteries are
insertedincorrectly
The batteries may be dead
Check the position of the
batteries
Replace the batteries
Water is dripping outside Hot and humid weather This is normal
Water is dripping inside the
room
The air conditioner is not
correctly tilted outside
For proper water drainage,
make sure the air onditioner
is slightly tilted downward
from the front of the unit to
the rear
Water collects in the base pan Moisture removed from the
air is draining into the base
pan
This is normal for a short
period inareas with low
humidity and normal for a
longer period in areas with
high humidity
23
ENGLISH
CUSTOMER SUPPORT
Visit our website to contact us, find answers to Frequently Asked
Questions, and for other resources which may include an updated version of this user’s
manual
www.impecca.com
If you wish to contact us by phone, please be sure to have your model number and serial
number ready and call us between 9:00am and 6:00pm ET, at +1 866-954-4440
Keep tabs on Impecca’s newest innovations and enter contests via our social network
feeds:
www facebook com/Impecca/
www instagram com/impecca/
@impeccausa
24
ENGLISH
ONE-YEAR LIMITED APPLIANCE WARRANTY (US)
Impecca™ warrants this product against defects in material
and workmanship to the original purchaser as specified be-
low.
PARTS AND LABOR– if the product is determined to
have a manufacturing defect, within a period of one
year from the date of the original purchase, Impec-
ca™, at its own discretion, will repair or replace the
product parts at no charge to you in the U.S.A.
To obtain warranty service by an authorized Impecca™ ser-
vice center, please email us at: service@impecca.com to ob-
tain a Repair and Maintenance Authorization (RMA) number
and received instructions on how the repair and/or replace-
ment procedure will take place.
Any glass materials included with the appliance will
be covered for a period of 60 days from purchase.
Impecca™ specifically excludes from this warranty any
non-electric/mechanical attachments, accessories and
disposable parts including but not limited to outside case,
connecting cables, batteries and AC adapters. Impecca™ re-
serves the right to repair or replace defective products with
the same, equivalent or newer models.
We reserve the right to either repair or replace product at our
discretion. Replacement may be either new or refurbished
and while every endeavor will be made to ensure it is the
same model, if not possible it will be equal or higher spec-
ification.
Normal “Wear and Tear” is not covered by this warranty. Fur-
ther, Impecca™ hereby reserves the right to determine “Wear
and Tear” on any and all products. Tampering or opening the
product casting or shell will void this warranty in its entirety.
Exclusions: This warranty does not cover the following:
1. Any product that has a defaced or covered serial num-
ber.
2. Products that have been transferred to a second owner.
3. Rust on the interior or exterior of the unit.
4. Products listed as “As-Is” or “Refurbished.”
5. Food loss due to any product failure.
6. Window air conditioners installed in a wall.
7. The product if used in a commercial setting.
8. Service calls that do not involve product malfunction.
9. Service calls for a product ruined by not following the
provided instructions.
10. Service calls to correct improper installation.
11. Costs associated with making the product accessible
for servicing (including but not limited to removal of
trim/molding/cabinetry, etc.)
12. Service calls to replace any consumables such as light
bulbs, filters, etc.
13. Surcharges that may apply to service calls on weekends,
nights, holidays. Damages to the finish of appliance or
household furnishings due to installation of appliance.
14. Damages caused by any of the following: Acts of God;
fires; misuse; accidents; incorrect power supply; service
performed by unauthorized persons; use of non-genu-
ine Impecca parts, etc.
ALL IMPLIED WARRANTIES, INCLUDING IMPLIED WARRAN-
TIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU-
LAR PURPOSE ARE LIMITED IN DURATION TO 1 YEAR FROM
THE DATE OF THE ORIGINAL RETAIL PURCHASE OF THIS
PRODUCT.
THESE WARRANTIES AND REMEDIES ARE THE SOLE AND
EXCLUSIVE WARRANTIES AND REMEDIES IN CONNECTION
WITH THE SALE AND USE OF THE PRODUCT. NO OTHER
WARRANTIES, ORAL OR WRITTEN, EXPRESSED OR IMPLIED,
ARE GIVEN.
IMPECCA™ IS NOT RESPONSIBLE OR LIABLE FOR ANY DAM-
AGE, WHETHER SPECIAL, INCIDENTAL, CONSEQUENTIAL,
DIRECT OR OTHERWISE, OR WHETHER KNOWN OR SHOULD
HAVE BEEN KNOWN TO IMPECCA™, INCLUDING LOST PROF-
ITS, GOODWILL, AND PROPERTY AND PERSONAL INJURY RE-
SULTING FROM ANY BREACH OF WARRANTY, THE INABILITY
TO USE THE PRODUCT OR UNDER ANY LEGAL THEORY IN
CONTRACT OR TORT. IMPECCA LIABILITY IS LIMITED TO THE
ACTUAL PURCHASE PRICE PAID TO THE RETAIL SELLER OF
THE DEFECTIVE PRODUCT.
No Impecca™ dealer, agent or employee is authorized to
make any modification, extension, change or amendment to
this warranty without the written consent and authorization
from Impecca™.
Some states do not allow the exclusion or limitation of im-
plied warranties or liability for incidental or consequential
damages, or do not allow a limitation on how long an im-
plied warranty lasts, so the above limitations or exclusions
may not apply to you. This warranty gives you specific legal
rights, and you have other rights, which vary from state to
state.
Note: Our Warranty center services only to Continental U.S.A.
ONE-YEAR LIMITED APPLIANCE WARRANTY (US)
25
ENGLISH
