Tournament Series
Livewell/Baitwell Pumps
Description
Powerful and long lasting, Rule Tournament Series Cartridge
Pumps offer outstanding performance as well as the versatility of
replacing the motor cartridge if the motor expires. The cartridge
feature also allows complete access to the impeller for easy
cleaning and maintenance. Replacing the motor cartridge only
allows the fittings and hose to remain totally intact.
To Change Motor Cartridge
1. Block off the thru-hull before removing the motor cartridge
2. Disconnect wiring
3. Press cartridge button, twist counterclockwise and pull
motor cartridge straight up
4. Reconnect wire to new motor cartridge
5. Align the arrows and press the new motor cartridge down
firmly. Twist motor housing clockwise until cartridge locks
in place
Instruction Guide
Models 401C, 403C, 405C, 401STC,
403STC, 405STC, 401FC, 403FC, 405FC
Replacement motors 45DR, 46DR,47DR
This pump is designed for
use with fresh and salt
water. Use with any other medium, including
particularly hazardous, caustic or corrosive
substance, could result in damage to the pump, the
surrounding environment and injury to persons or
property, including possible exposure to hazardous
substances. This pump is for water applications only.
WARNING
Model #
Description
R
equired GPH at GPH at
Fuse Size (A)
Open Flow 3.35 ft.
401 C 500 GPH Livewell Pump with Angled Pickup Tube 2.5 500 340
403 C 800 GPH Livewell Pump with Angled Pickup Tube 5 800 490
405 C 1000 GPH Livewell Pump with Angled Pickup Tube
6
1000
710
401ST
C 500 GPH Livewell Pump with Straight Pickup Tube 2.5 500 340
403STC 800 GPH Livewell Pump with Straight Pickup Tube 5 800 490
405STC 1100 GPH Livewell Pump with Straight Pickup Tube 6 1100 790
401 FC 500 GPH Livewell Pump with 1" Straight Pickup Tube 2.5 500 340
403 FC 800 GPH Livewell Pump with 1" Straight Pickup Tube 5 800 490
405 FC
1100 GPH Livewell Pump with 1" Straight Pickup Tube 6 1100 790
Replacement Motors
45DR 500 GPH Replacement Motor 2.5 500 340
46DR
800 GPH R
eplacement Motor
5
800
490
47DR
1000 GPH Replacement Motor 6 1100 790
Press Cartridge
Release Button
To remove motor cartridge:
Twist Cartridge
Counterclockwise
Pull Cartridge
Straight Up
a.
b.
c.
c
a
b
Models
Dimensions in inches (mm)
B
A
A
B
2
.76 (70)
2.76 (70)
2
.76
(
70)
2.76
(
70)
C
C
E
E
E
C
D
D
D
Models
4
01 STC
403 STC
4
05 STC
Models
4
01 FC
403 FC
4
05 FC
Models
4
01 C
403 C
4
05 C
Model A B C D E
4
01C 4.0 (102) 5.87 (149) 3/4-14NPSM 1/2-14NPT 3/4-14NPSM
403C 4.0 (102) 5.87 (149) 3/4-14NPSM 1/2-14NPT 3/4-14NPSM
4
05C 4.0 (102) 5.87 (149) 1-11.5NPSM 1/2-14NPT 3/4-14NPSM
401STC 4.33 (110) 5
.84 (148) 3/4-14NPSM 1
/2-14NPT 3/4-14NPSM
403STC 4.33 (110) 5
.84 (148) 3/4-14NPSM 1/2-14NPT 3/4-14NPSM
405STC 4.33 (110) 5.84 (148) 1-11.5NPSM 1/2-14NPT 3/4-14NPSM
401FC 5.87 (149) 3/4-14NPSM 1/2-14NPT 3/4-14NPT
403FC 5.87 (149) 3/4-14NPSM 1/2-14NPT 3/4-14NPT
405FC 5.87 (149) 1-11.5NPSM 1/2-14NPT 3/4-14NPT
Mounting the Pump
(Models 401C, 403C, 405C, 401STC,
403STC 405STC)
1. Drill a 1” diameter hole through the transom or hull
bottom. If drilling through the transom, make sure the
hole inside the boat is beneath the waterline outside the
boat when the boat is standing still.
2. Place the pump into the hole with the gasket in place on
the inside of the boat.
3. Tighten the nut on the outside of the hull until you are sure
the gasket ring is tightly sealed. Be careful not to over-
tighten. Make sure outlet is at least parallel with boat
bottom. This helps prevent airlocks.
4. Saw off the excess length of the pickup tube so it is flush
with the outside surface of the nut. In the event you are
using a strainer (Rule Model 73), leave 1/2” beyond the
nut. Make sure the cut is square and the threads de-
burred to allow the debris strainer to fit smoothly.
By lifting the locking ring, you can rotate the position of the
discharge nozzle so that the discharge is facing toward the
tank (see diagram below).
(Models 401FC, 403FC 405FC)
Seacock applications
1. Drill a 1” diameter hole through the
transom or hull bottom. If drilling
through the transom, make sure
the hole inside the boat is beneath
the waterline outside the boat
when the boat is standing still.
2. Install a thru-hull pickup tube with a filter grate to prevent
debris from entering the seacock and the pump. Use a
marine sealant on the flat surface of the thruhull where it
will be in contact with the outside surface of the boat and
around the threaded tube on both sides of the hull. Install
the seacock and pump using pipe tape or sealant on all
threaded connections.
3. Screw the pump into the seacock until it is hand tight. Do
not over-tighten.
4. If the pump is mounted horizontally, the output must be
pointed upward to allow air to vent.
KEEP SEACOCK VALVE CLOSED WHEN LIVEWELL IS
NOT IN USE
Electrical
WIRE: Normal installations require 16 gauge wire.
POLARITY: Brown pump wire connects to the positive (+)
side of the battery. Black pump wire connects to the negative
(-) side of the battery.
FUSE: Install proper size fuse & holder in the positive (+)
brown wire between the pump and the battery.
500 GPH pumps (Models 401C, 401STC, 401FC) -
INSTALL A 2.5 AMP FUSE
800 GPH pumps (Models 403C, 403STC, 403FC) -
INSTALL A 5.0 AMP FUSE
1100 GPH pumps (Models 405C, 405STC, 405FC) -
INSTALL A 6.0 AMP FUSE
IMPORTANT - THIS PRODUCT SHOULD BE
INSTALLED WITH THE RECOMMENDED FUSE SIZE
NOTE: Keep all wire connections and joints above highest
possible water level.
Seal wire connections with a marine sealant to prevent
corrosion.
Hose Connection
Dual Port Option
Each pump is fitted with an additional 1/2” NPT
female port
and Hex Plug. This feature allows you to add your washdown
pump without adding another thru-hull fitting.
• Use a marine ribbed hose that will not kink with bends and
is rated for below water line use.
• Hose should run uphill evenly from pump to livewell tank.
You may use a control valve to regulate the flow.
•
Use hose clamps when making connections to pump and valve.
Pump Discharge
Can Rotate 360
°
Raise Ring to
Allow Pump
to Rotate
THE PUMP IS BELOW
THE WATERLINE.
WATER CAN COME
INTO THE BOAT THROUGH THE PUMP IF THE
HOSE IS NOT CONNECTED TIGHTLY TO THE PUMP.
CAUTION
© Copyright 2006 All Rights Reserved Form: 950-0213 Rev. A 06/2006
Rule
1 Kondelin Road
Gloucester, MA 01930
Tel: 978-281-0573
Fax: 978-283-2619
Made in China
www.rule-industries.com
