Headphones
TAT1320
User manual
Register your product and get support at
www.philips.com/support
1 Important Safety Instructions 2
Hearing Safety 2
General information 2
2 Your true wireless earpieces 3
What is in the box 3
Other devices 3
Overview of your true
wireless earpieces 4
3 Get started 5
Charge the battery 5
How to wear 5
Pair the earpieces with your
6
Pair the earpieces with another
Bluetooth device 6
4 Use your earpieces 7
Connect the earpieces to your
Bluetooth device 7
P
7
Manage your calls and music 7
Voice assistant 8
Earpieces LED indicator status 8
Charging case LED indicator status 8
5 Reset the earpieces 9
6 Technical data 9
7 Notice 10
Declaration of conformity 10
Dispose of your old product and
battery 10
Remove the integrated battery 10
Compliance with EMF 11
Environmental information 11
Notice of compliance 11
8 Trademarks 13
9 Frequently asked questions 14
Contents
EN2
1 Important
Safety
Instructions
Hearing Safety
Danger
• To avoid hearing damage, limit the time you use
earpieces at high volume and set the volume to
a safe level. The louder the volume, the shorter
the safe listening time is.
Be sure to observe the following
guidelines when using your earpieces.
• Listen at reasonable volumes for
reasonable periods of time.
• Be careful not to adjust the volume
continuously upwards as your
hearing adapts.
• Do not turn up the volume so high
that you can’t hear what’s around
you.
• You should use caution or temporarily
discontinue use in potentially
hazardous situations.
• Excessive sound pressure from
earpieces and headphones can cause
hearing loss.
• Using earpieces with both ears
covered while driving is not
recommended and may be illegal in
some areas.
• For your safety, avoid distractions
from music or phone calls while in
environments.
General information
To avoid damage or malfunction:
CAUTION
• Do not expose earpieces to excessive heat.
• Do not drop your earpieces.
• Earpieces shall not be exposed to dripping or
product.)
• Do not allow your earpieces to be submerged
in water.
• Do not charge your earpieces when the
connector or socket is wet.
• Do not use any cleaning agents containing
alcohol, ammonia, benzene or abrasives.
• If cleaning is required, use a soft cloth, if
necessary dampened with a minimum amount
of water or diluted mild soap, to clean the
product.
• The integrated battery shall not be exposed to
• Danger of explosion if batteries are incorrectly
replaced. Replace only with the same or
equivalent type.
•
slot cover must be closed.
•
mechanically crushing or cutting a battery, can
result in an explosion.
• Leaving a battery in an extremely high
temperature surrounding environment that
can result in an explosion or the leakage of
• A battery subjected to extremely low air
pressure that may result in an explosion or the
•
only by external power source which output
shall comply with PS1 (with output capacity
less than 15W).
Operating and storage temperatures and
humidity
•
Store in a place where the temperature
is between -20°C (-4°F) and 50°C (122
°F) with up to 90% relative humidity.
•
Operate in a place where the
temperature is between 0°C (32°F) and
45°C (113 °F) with up to 90% relative
humidity.
•
Battery life may be shorter in high or
low temperature conditions.
•
Replacement of a battery with an
incorrect type risks severely damaging
the earpieces and the battery (for
example, in the case of some lithium
battery types).
3EN
2 Your true
wireless
earpieces
Congratulations on your purchase, and
your product at
www.philips.com/support. With these
Philips True wireless earpieces you can:
• Enjoy convenient wireless handsfree
calls
• Enjoy and control music wirelessly
• Switch between calls and music
What is in the box
Philips true wireless earpieces
Philips TAT1320
Type-C charging cable
(for charging only)
Quick Start Guide
Warranty
Safety lea�et
Other devices
A mobile phone or device (e.g. notebook,
tablet, Bluetooth adapters, MP3 players
etc) which supports Bluetooth and is
compatible with the earpieces.
www.philips.com/welcome
Headphones
TAT1320
Silicone ear tip cover
EN4
Overview of true
wireless earpieces
① LED indicator (earpieces)
② Multi-function touch (MFT)
③ Charging pogo pin
④ LED indicator (battery state or
charging state)
⑤ USB-C charging port
②
①
③
④
⑤
5EN
3 Get started
Charge the battery
Note
• Before you use your earpieces, place them
in the charging case and charge the battery
for 2 hours for optimum battery capacity and
lifetime.
• Use only the original USB-C charging cable to
avoid any damage.
• Finish your call before charging. Connect the
earpieces to the charger, the earpieces will turn
• If the earpieces are not used for a long time,
the rechargeable battery will begin to lose its
charge. To avoid this loss, please fully charge
the battery at least once every three months.
Charging case
Plug one end of the USB-C cable into the
charging case and the other end into the
power source.
Tips
• The charging case serves as a portable backup
battery for charging the earpieces. When
the charging case is fully charged, it will fully
recharge the earpieces 2 times.
Earpieces
Place the earpieces into the charging case
and close the lid.
• The earpieces begin charging, and the
white LED indicator stays on.
• The white LED indicator light turns off
when the earphones are fully charged.
Tips
• Normally, a full charge takes 2 hours (for the
earpieces or charging case) by USB cable.
How to wear
Insert the earpieces
1
Check left or right orientation of the
earpieces.
2
Insert the earpieces into the ears
achieved.
EN6
Pair the earpieces with
1
Make sure that the earpieces are fully
2
Open the top cover of the charging
case, take out the earphones and they
will automatically turn on.
»
»
The earpieces are now in pairing
mode and are ready to pair with
a Bluetooth device (e.g. a mobile
phone)
3
Turn on the Bluetooth function of
your Bluetooth device.
4
Pair the earpieces with your
Bluetooth device, refer to the user
manual of your Bluetooth device.
Note
•
any previously connected Bluetooth device, put
them into pairing mode (if the last connected
device is unavailable, the earpieces will enter
pairing mode one minute later).
The following example shows you how
to pair the earpieces with your Bluetooth
device.
1
Turn on the Bluetooth function
of your Bluetooth device, select
2
Enter the earpieces' password “0000”
(4 zeros) if prompted. For those
devices featuring Bluetooth 3.0 or
higher, there is no need to enter a
password.
Single earpiece (Mono mode)
Take either right or left earpiece
out from charging case then close
the charging case for Mono use, the
earpieces will turn on automatically.
Note
• Open the charging case, the earpieces will pair
with each other automatically.
Pair the earpieces with
another Bluetooth device
If you want to pair another Bluetooth device
with the earpieces, simply disconnect the
current connected Bluetooth device and
pair it with the other device using the usual
pairing method
Note
• The earpieces can store 4 devices in the
memory. If you try to pair more than four
devices, the earliest paired device will be
replaced by the new one.
TAT1320.
Philips TAT1320
The white light on the main ear
�ashes, and it goes out on the
secondary ear
7EN
4 Use your
earpieces
Connect the earpieces to
your Bluetooth device
1
Turn on the Bluetooth function of
your Bluetooth device.
2
Open the charging case cover, remove
the earphones, and turn on the
earphones:
»
»
The earpieces will search for the
last connected Bluetooth device
and automatically reconnect with
it. If the last connected device is
unavailable, the earpieces will
automatically enter pairing mode,
and users can discover the
earpieces on their phone and
choose to connect them.
The white LED indicator light is
�ashing.
Tips
•
Note
• If you �rst turn on the earphones and then turn
on the Bluetooth function of the Bluetooth
device, you must go to the Bluetooth menu of
the device and manually connect the earphones
to the Bluetooth device.
P
Task MFT Action
Turn on the
earpieces.
Turn on the
earpieces.
Open the top cover
of the charging case,
take out the
earpieces and they
will automatically
turn on
Press and hold for 5
seconds to turn on
the earpieces
Turn the
earpiec
Put back the charging
case, the earpieces will
automatically shut
down
Manage your calls and
music
Music control
Task MFT Action
Play or pause
music
R/L earpiece
R/L
earpieces
Double tap
Next track Right
earpiece
Triple Tap
Previous track Left earpiece Triple Tap
Adjust volume
+
Right
earpiece
Tap once
then long
touch
Adjust volume - Left
earpiece
Tap once
then long
touch
(The earpieces are
outside the
compartment
and turned off)
If you �rst turn on the earphones and then
turn on the Bluetooth function of the Bluetooth
device, you must go to the Bluetooth menu of
the device and manually connect the earphones
to the Bluetooth device.
EN8
Call control
Task MFT Action
Pick up a call R/L earpiece Single click
Hang up call R/L earpiece Double tap
Double tap
Reject a call R/L earpiece
Voice assistant
Task Button Action
Trigger voice
assistant
(Siri/Google)
R/L earpiece Press and
hold for 2
seconds.
Stop Voice
Assistant
R/L earpiece Long press
for 1 second
Earpieces LED indicator
status
Earpieces status Indicator
The earpieces
are connected to
Bluetooth
The indicator light
is off
The earpieces are
ready for pairing
White light �ashing
The earpieces are on
but not connected to
a Bluetooth device
White light �ashing
Low battery level
(earpieces)
The white indicator
light �ashes three times
every 5 seconds
Battery is fully
charged (charging
case)
Refer to case LED
Charging case LED
indicator status
When charging Indicator
Charging
case charging
in progress
Fully charged
White light �ashing
The white light is
always on
9EN
5 Reset the
earpieces
If you encounter any pairing or
connection issue, you can follow the
following procedure to reset your
earpieces to factory default settings.
1 On your Bluetooth device, go to
the Bluetooth menu and remove
from the device list.
2
your Bluetooth device.
3 Take the earpieces from the charging
case (ensure they are not connected
to a Bluetooth device)
4 Press and hold MFT on both earpieces
for 4 seconds to erase all data.
5 Follow steps in “Use your earpieces
- connect the earpieces to your
Bluetooth device.”
6 Pair the earpieces with your Bluetooth
device, select
6 Technical data
• Music time: 7+21 hours
• Charging time: 2 hours
• Lithium-ion battery 40 mAh on each
earpiece, Lithium-ion battery
400 mAh on charging case
• Bluetooth version: 6.0
•
•
• A2DP (Advanced audio
• AVRCP (Audio Video Remote
• Supported audio codec: SBC
• Frequency range: 2.402-2.480GHz
• Transmitter power: < 10 dBm
• Operating range: up to 10 meters
(33 feet)
•
• USB-C port for charging
• Low battery warning: available
Note
•
notice.
Philips TAT1320
Philips TAT1320.
EN10
7 Notice
Declaration of conformity
Hereby, MMD Hong Kong Holding
Limited declares that the product
is in compliance with the essential
requirements and other relevant
provisions of RED Directive 2014/53/EU
and UK Radio Equipment Regulations
Declaration of Conformity on
www.philips.com/support.
Dispose of your old
product and battery
Your product is designed and
manufactured with high quality
materials and components, which can be
recycled and reused.
This symbol on a product means that the
product is covered by European Directive
2012/19/EU.
This symbol means that the product
contains a built-in rechargeable battery
covered by European Directive 2013/56/
EU which cannot be disposed of with
normal household waste. We strongly
advise you to take your product to an
service centre to have a professional
remove the rechargeable battery.
Inform yourself about the local separate
collection system for electrical and
electronic products and rechargeable
batteries. Follow local rules and never
dispose of the product and rechargeable
batteries with normal household
waste. Correct disposal of old products
and rechargeable batteries helps
prevent negative consequences for the
environment and human health.
Remove the integrated
battery
If there is no collection/recycling system
for electronic products in your country,
you can protect the environment by
removing and recycling the battery
before disposing of the earpieces.
• Make sure the earpieces are
disconnected from the charging case
before removing the battery.
• Make sure the charging case is
disconnected from the USB charging
cable before removing the battery.
11EN
Compliance with EMF
This product complies with all applicable
standards and regulations regarding
Environmental
information
All unnecessary packaging has been
omitted. We have tried to make the
packaging easy to separate into three
materials: cardboard (box), polystyrene
and protective foam sheet).
Your system consists of materials
which can be recycled and reused if
disassembled by a specialized company.
Please observe the local regulations
regarding disposal of packaging
materials, exhausted batteries and old
equipment.
Notice of compliance
The device complies with the FCC rules,
Part 15. Operation is subject to the
following two conditions:
1.
2.
This equipment has been tested and
found to comply with the limits for
a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits
are designed to provide reasonable
protection against harmful interference
in a residential installation. This
equipment generates, uses and can
radiate radio frequency energy and, if
not installed and used in accordance
with the instruction manual, may
cause harmful interference to radio
communications.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does
cause harmful interference to radio
or television reception, which can be
determined by turning the equipment
try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving
antenna
• Increase the separation between
equipment and receiver
• Connect the equipment into an outlet
which the receiver is connected.
• Consult the dealer or an experienced
radio/TV technician for help.
This equipment complies with FCC
radiation exposure limits set forth for an
uncontrolled environment.
This transmitter must not be co-located
or operated in conjunction with any
other antenna or transmitter.
this unit not expressly approved by the
party responsible for compliance could
void the user’s authority to operate the
equipment.
This device contains license-exempt
transmitter(s) / receiver(s) that comply
with Innovation, Science and Economic
Development Canada’s license-exempt
RSS(s). Operation is subject to the
following two conditions: (1) This device
may not cause harmful interference. (2)
This device must accept any interference
received, including interference that may
cause undesired operation of the device.
EN12
This equipment complies with Canada
radiation exposure limits set forth for
uncontrolled environments.
This transmitter must not be co-located
or operated in conjunction with any
other antenna or transmitter.
CAN ICES-003(B)/NMB-003(B)
13EN
8 Trademarks
Bluetooth®
The Bluetooth® word mark and logos
are registered trademarks owned
by Bluetooth SIG, Inc. and any use
of such marks by MMD Hong Kong
Holding Limited is under license. Other
trademarks and trade names are those
of their respective owners.
Siri
Siri is a trademark of Apple Inc.,
registered in the U.S. and other
countries.
Google
Google and Google Play are trademarks
of Google LLC.
EN14
9 Frequently
asked
questions
The battery level is low. Charge the
earpieces.
Bluetooth is disabled. Enable the
Bluetooth feature on your Bluetooth
device and turn on the Bluetooth device
before you turn on the earpieces.
• Put both earpieces into charging
case.
• Make sure you have disabled the
Bluetooth function of any previously
connected Bluetooth devices.
• On your Bluetooth device, delete
“Philips TAT1320 ” from the Bluetooth
list.
• Pair your earpieces (see ‘
Pair the
’ on page 6).
• The earpieces may be connected to a
connected device or move it out of
range.
• Pairing may have been reset or the
earpieces have been previously
paired with another device. Pair
the earpieces with the Bluetooth
device again as described in the user
manual. (see ‘
Pair the earpieces with
time
’ on page 6).
Refer to the user manual of your mobile
phone. Select to listen to music through
the earpieces.
• The Bluetooth device is out of range.
Reduce the distance between your
headset and Bluetooth device, or
remove obstacles between them.
• Charge your headset.
Make sure your mobile phone not
only supports (mono) HFP but also
supports A2DP and is BT4.0x (or higher)
compatible (see ‘
Technical data
’ on
page 9).
2025 © MMD Hong Kong Holding Limited. All rights reserved.
and the Philips Shield Emblem are registered trademarks of
Koninklijke Philips N.V. and are used under license. This product
has been manufactured by and is sold under the responsibility
MMD Hong Kong Holding Limited is the warrantor in relation
to this product. All other company and product names may be
trademarks of its respective companies with which they are
associated.
UM_TAT1320_70_EN_V1.0
