Empava EMPV-71PRO04 71-Inch Alcove Dual Massage Whirlpool Inline Heater 2-Person Bathtub with Center Drain

Product's Documents

Below are documents related to this product, you can read online or download:
User Manual Specification
EMPV-71PRO04 photo

User Manual

This is the main product document for model EMPV-71PRO04. Additionally, the document applies to other Empava models: EMPV-71PRO04

The file format is pdf, 2 pages, you can download this manual here .

background
MASSAGE BATHTUB
MODEL:
EMPV-71PRO04
This p
roduct uses universal home power.
The drain pipe is 31.5" long and the ground drain
should be 12" – 20" away from the bathtub drain so
that the drainpipe can form an S-bend for
odor isolation
12″
User needs to purchase two separate 110/120V 15amp plugs and
install the proper dedicated plug with a ground electrode to
the power line. Then insert the plug frmly.
Note: This product uses universal home power.
External circuitry is equipped with high sensitive and fast type
leakage protection switch. (Induced current rating below 15MA; trip
time should be less than 0.1 second; rated current is above 30A.)
Make sure the ground is connected. One side of
the ground should be connected to the ground
terminal of the motor and the stainless steel
frame; the other side should be connected to
the ground wires of the plug.
How to connect the ele ctricity?
Ground terminal
The ground wire
from the switch
goes into this screw
N
L
Tomaincontrolbox
From electrical source
110-120V
The product should be installed
alongside ground and electric leakage
switches by a licensed electrician.
Notice
The bathtub must be connected to the ground.
The power outlet must be sealed well.
Notice
Make sure the surface of each wire is intact.
Filter
screen
Although all our massage bathtub are water tested before they leave our factory,
d. Insert the plug, start all the function for few minutes (which includes the
functions of massage ), inspect the tub
completely any defect must be reported to your dealer/distributor prior to
installation in order to have it covered under
warranty.
3
.
1
"
transferable switch
cold water
hot water
overflow
water jet
water inlet
shower head
hydrodynamic adjust
control panel
70. 9"
41"
34.6"
10
.6"
4
7
.
2
"
19
.6"
2
4.8"
suction
air jet
drainer
pillow rest
Size chart
background
SHOWER HEAD
RUBBER GASKET
HOSE CONNECTOR
SHOWER HOLDER
BATHTUB
Regular bathtub maintenance will keep it clean and working at its best. Pump and
pipe circulation systems should be fushed before frst use and on a monthly basis
Care and Maintenance
when product is under normal use. Below is the recommended cleaning procedure:
1.Do not run the jet massage system dry.
2.Fill the tub with hot water (abou t ( 40°C )) 2-3 cm (0.9-1.2 inch) above the jets. Add 2-3
teaspoons of low foaming detergent, such as dishwashing machine detergent.
3.Turn on all the functions and run for 10 minutes.
4.Drain tub completely.
5.Fill tub with cold water above jets.
6.Turn on all the functions and run for 15 minutes.
7.Drain tub completely.
8.Clean the “suction cover” by removing any hair or lint.
Whirlpool Suction Cover/Strainer
Maintain regular cleaning of the suction cover/strainer
1. Rotate the suction cover to the left to detach it.
2. Remove any hair, lint, or debris present on the cover and
housing.
3. Remember to reattach the cover in place.
Keep hair a minimum of 6 inches (152 mm) away from the suction ftting at all times
when the whirlpool system is operating. Individuals with shoulder-length hair
should secure it close to their heads or wear a bathing cap.
Do not operate the Whirlpool system with the suction cover/strainer removed! It is
a safety device and must always be in place on the suction ftting to minimize the
a.
b.
WARNING! Please orient the cover/strainer with the small
notch at the bottom. The gasket must be inserted into the
groove of the cover/strainer before mounting it onto the
suction ftting.
DANGER: RISK OF SEVERE INJURY OR DROWNING!
potential hazard of hair and body entrapment.
SHOWER HEAD INSTALLATION
Tmaking sure it lies flat.o install the shower head, follow the steps shown in
Figure A.
First, remove the hose connector from the shower holder.
Then, insert the rubber gasket into the hose connector,
Finally, tighten the shower head and the hose connector securely.
SHOWER INSTALLATION
SNY-371
Screen
left
Right
pump can not start .The pump will be turned off automatically every 60 minutes .
2 Surfing function
OKOK
Operation
1 ON/OFF insert the plug ,press to switch on the power .The screen will
show the temperature of water and the lamp will light up.You can perform setting
and operation of various function according to the requirement of users .The system
can be directly switch off by pressing
.
To press OK
for ON or OFF
Notice The water pump is limited by water level ,it only be launched under
the condition of water level .If short of water ,the 󶙱 󶙱the will flicker ,water
Press
or
to
select the lamp icon ,as shown
to the right
The light will illuminate and change colors automatically when the control panel
is turned on. Press OK to change different light colors.
In the event of a water shortage( below the the minimum water level), it will be
indicated by a fashing icon , and water pump will be unable to operate .
The pump will turn off automatically every 60 minutes.
The air bubbles will turn off automatically every 60 minutes.
3 Heating function
OKOK
OKO K
6 Lamp when power on ,it will light up ,and when power off ,it
will light off.
red blue green seven color allochroism white
OKO K
it will change thecolor each time you press OK
Press
or
to
select the heating icon as
shown to the right
To press OK
for ON or OFF
Notice only under the surfing function on ,the heating function can be
launched ,and control by the preset temperature .
Default 40 When the water temperature reach to the
preset temperature ,it will turn into constant temperature .
4 Bubble bath function
(It will be turned off automatically every 60minutes .)
Press
or
to
select the bubble bath icon ,as
shown to the right :
To press OK
for ON or OFF
Press
or
to
select the lamp icon ,as shown
to the right
Color variable .
(it will change
the color each
time you press.)
Notice: It will light up when the power on ,only power off can light off
the lamp .The above only can change the color .
The heater is equipped with a preset vacuum switch that prevents it from
activating if the pump is not running and water is not fowing through the
whirlpool system. As a result, only when water jets are on, the heating function
can be activated, and the temperature can be adjusted accordingly.
The heater will only function when the water temp is 77°F or higher. It is
recommended to fll the bathtub with warm water to ensure that the heater can
function as intended.
When the water temperature reaches 104°F ( 40°C ), the inline heater will
automatically shut off.
Automatic keyboard locking : If no action on the keyboard for 2 minutes, icon
will appear on the screen, indicating that the keyboard is locked
automatically.
Please press OK to unlock the keyboard.
When not in use, please keep the bathtub well-ventilated and dry;
avoid contact with corrosive substances; cut off electricity and cut off
water supply.
To avoid other damage, please do not drop or strike the bathtub with
hard objects. Doing so could crack or scratch the bathtub or cause
leaks that damage or ruin household property.
When the product is at work, you cannot cut off any connection lines
and split the bus master and control panel. Any part of the control
panel and the bus master CAN NOT be split by the user. Doing so
may cause product leakage, electric shock, or other accidents.
The ground fault circuit interrupter (GFCI) should be tested regularly.
It is ideal to test before each use.
Use water or mild detergent to clean the product. Do not use acids,
alkalis, chemical organic solvents, or acidic/alkaline cleaning agents.
Otherwise, the bathtub will experience surface damage. When water
or a neutral detergent cannot remove stains, use a clean cloth with a
little alcohol to remove stains.
Plating parts maintenance: use cotton fabric to scrub.
Light scratches and dulled areas may be restored to original luster by
coarse grinding using NO. 1200 waterproof sandpaper dipped in water.
Then fne grind by using NO. 2000 waterproof sandpaper dipped in
water. Finally, polish with a soft cloth and a polishing agent.
When not in use, please keep the bathtub well-ventilated and dry;
avoid contact with corrosive substances; cut off electricity and cut off
water supply.
Always implement countermeasures that help prevent freezing. You
must empty the bathtub and the water in the pipe during winter
use. If the pipes freeze, the pipes could rupture or equipment could
become damaged.
Use no water other than standard tap water. The use of well water
could cause corrosion, which could lead to leaks.
The bathtub should not be exposed to ultraviolet or bright light,
otherwise aging could be accelerated, causing damage.
Keep the bathtub away from cigarette butts, hair dryers, and other
heat sources, otherwise the product may be damaged due to high
temperature deformation.
Troubleshooting Guide
PROBLEMS CAUSES SOLUTIONS
Pump/motor and jets do not
operate
1. No power to pump/motor
2. Water level does not reach high
enough
3. Air hose connected to the pneumatic
switch is loose
4. Defective Pump/motor
1. Check for power supply and power connections.
2. Inflow water until it reaches the minimum water
level of the bathtub
3. Tighten the loose air hose and pneumatic
switch connection
4. Contact Empava for WARRANTY & SERVICE
Not all jets are functioning • Jets are closed
1. Adjust the jets by rotating
clockwise/anticlockwise
2. Contact Empava for WARRANTY & SERVICE
Water leakage from pump/motor
1. O ring is pinched or faulty
2. Screw nut is not tightened or
connected properly
1. Replace the old ring
2. Tighten the screw nut and make sure it's in
good connection
3. Contact Empava for WARRANTY & SERVICE
Water leakage from PVC pipes The glass glue is not enough
1. Apply glass glue to seal it
2. Contact Empava for WARRANTY & SERVICE
Water leakage from drainage
1. O ring is pinched or faulty
2. Drain pipe is broken
1. Replace the old ring or the drainer
2. Replace the drain pipe
3. Contact Empava for WARRANTY & SERVICE
Water leakage from hardware
1. O ring is pinched or faulty
2. Defective control valve
1. Replace the old ring or faucet/showerhead
2. Replace the control valve under knobs
3. Contact Empava for WARRANTY & SERVICE
Empava® APPLIANCES
Please have the following information available when you call/
email the Empava Customer Center:
Proof of purchase (PO# or screenshot of order confrmation)
Model number and serial number
A clear and comprehensive description of the issue
•
•
PROOF OF PURCHASE IS REQUIRED TO OBTAIN
•
WARRANTY SERVICE.
IF YOU NEED SERVICE: Empava Customer Center
Address: 15253 Don Julian Rd, City of Industry, CA 91745
Website: https://empava.com
Call: 888-682-8882 Monday - Friday from 9am - 5pm PST
Empava® APPLIANCES WARRANTY
WHAT IS NOT COVEREDWHAT IS COVERED
HEREIN. EMPAVA SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow
the exclusion or limitation of incidental or consequential damages, so these limitations and exclusions may not apply to you. This
warranty gives you specifc legal rights, and you also may have other rights that vary from state to state or province to province.
The effective date of the warranty commences from the
date of original consumer purchase. If the appliance is
installed, operated, and maintained in accordance with the
user manual, Empava will provide parts at no cost to rectify
any defects in materials and workmanship that were present
at the time of purchase. Alternatively, at its sole discretion,
Empava may replace the product. In the event of product
replacement, the warranty for the replacement product shall
be valid for the remaining term of the original warranty
period.
Empava offers a two-year warranty on parts for the following
categories: induction cooktop, gas cooktop, electrical oven,
pizza oven, fre glass, juicer, range hood, wine cooler, beverage
refrigerator and toilet seat
TWO YEARS WARRANTY (PARTS)
Empava offers a two-year warranty on both parts and labor for
the following categories: gas oven and gas range.
TWO YEARS WARRANTY (PARTS & LABOR)
Empava provides a three-year warranty on both parts and labor
for the following categories: freestanding tub, massage tub, and
walk-in tub.
This limited warranty is valid for products that are either
purchased brand new from an authorized Empava dealer or
directly from Empava.
THREE YEARS WARRANTY (PARTS & LABOR)
LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES·
If you want a longer or more comprehensive warranty than the limited warranty that comes with this major appliance, you should ask
Empava or your retailer about buying an extended warranty.
DISCLAIMER OF REPRESENTATIONS OUTSIDE OF WARRANTY
IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR A
PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and provinces do not
allow limitations on the duration of implied warranties of merchantability or ftness, so this limitation may not apply to you. This warranty
gives you specifc legal rights, and you also may have other rights that vary from state to state or province to province.
Commercial, non-residential or multiple-family use, or use
inconsistent with published user, operator or installation
instructions.
In-home Instruction on how to use your product.
Service to correct improper product maintenance or
installation, installation not in accordance with electrical or
plumbing codes or correction of household electrical or
plumbing (i.e., house wiring, fuses or water inlet hoses).
Defects or damage caused by the use of non-genuine
Empava parts or accessories.
Conversion of your product from natural gas or L.P. gas.
Damage from accident, misuse, abuse, fre, foods, acts of
God or use with products not approved by Empava.
Repairs to parts or systems to correct product damage or
defects caused by unauthorized service, alteration or
modifcation of the appliance.
Cosmetic damage including scratches, dents, chips, and
other damage to appliance fnishes unless such damage
results from defects in materials and workmanship and is
reported to Empava within 30 days.
Discoloration, rust or oxidation of surfaces resulting from
caustic or corrosive environments including but not limited
to high salt concentrations, high moisture or humidity or
exposure to chemicals.
Food loss due to product failure.
Removal or reinstallation of inaccessible appliances or
built-in fxtures (i.e., trim, decorative panels, fooring,
cabinetry, islands, countertops, drywall, etc.) that interfere
with servicing, removal or replacement of the product.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
DISCLAIMER OF IMPLIED WARRANTIES
EMPAVA APPLIANCES INC.
15253 DON JULIAN RD CITY OF INDUSTRY,CA 91745
TEL:888-682-8882
WWW.EMPAVA.COM
WARNING!
CALIFORNIA RESIDENTS
Cancer and Reproductive Harm
¡ADVERTENCIA!
RESIDENTES DE CALIFORNIA
Cáncer y Daño Reproductivo
AVERTISSEMENT!
RÉSIDENTS DE CALIFORNIE
Cancer et Dommages à la Reproduction
w w w .P 65W arnings.ca.gov
hot
cold
A
B
shower
head
water
inlet
Pipe flushing
A.hot water switch
(Marked with letter H)
C.cold water switch
(Marked with letter C)
B.Functional changeover
valves.(Showerhead/
Water/Pipe flushing)

Specifications

Empava EMPV-71PRO04 Questions and Answers

Questions and Answers

Related Products