PT Series Manual Trolley – Installation and Safety Instructions
JET Manual Trolleys are designed to be used on either "Ι" or “H” wide flange beams.
JET PT Series Trolleys comply with OSHA regulations, ANSI/ASME B30.11 and B30.17 standards.
1. Beam must be properly installed and rated for anticipated loads.
2. Do not install trolley on beams of unknown capacity.
3. Do not install trolley on damaged or deformed beams.
4. JET trolleys are designed to be used with hoists of the same rated capacity. Never use a hoist with a capacity
greater than the capacity of the trolley.
5. Never subject trolley to a side pull or load. Load must be centered directly under the hoist / trolley assembly.
6. Make sure load is stable and secure before moving.
7. Never lift load more than is necessary to safely move it.
8. Always follow installation instructions.
9. Do not use if under the influence of drugs, alcohol, or medication.
Installation Instructions
(refer to drawing at right)
1. Trolley must be installed on a beam with a
minimum clearance (wheels to flange) of 1/16" to
a maximum of 1/8". Reference "A" on both sides
of the beam.
2. To extend trolley width, remove split pins and hex
nuts. Remove washer spacers from center bolt
and place between hanger bracket and fixed
spacer. Note: Washer spacers must be moved in
sets of two, one on either side of the hanger
bracket, as the hanger bracket must always
remain centered between the trolley side plates.
3. Once trolley width is spaced properly, install
remaining washer spacers on the center bolt
(same number on both sides) on the outside of the
side plates. Install hex nuts and split pins. Do not
over tighten nuts. Tighten nuts and then back
nuts off to align the nut with hole in shaft for split
pin. Insert split pin through each hex nut and bend
one end of split pin.
4. Re-check wheel clearance "A" and re-adjust if necessary.
WALTER MEIER (Manufacturing), Inc.
427 New Sanford Road
LaVergne, Tennessee 37086 Part No. M-252005
Ph.: 800-274-6848 Revision B 04/2013
www.jettools.com Copyright © 2013 Walter Meier (Manufacturing) Inc.
PT Series Trolley: Specifications and Parts List
Capacity
Stock
No.
Beam
Flange
Width “G”
(min–max)
Beam
Height
(min-max)
Min.
Radius
Curve
Shipping
Weight
A B
C
(Ø)
D
E
(Ø)
F G H J
1/2 Ton 252005
mm 64–203 76–622 900 8.5 (kg) 212 312 58 130 82 102 64–203 113 24
in. 2-1/2–8 3–24.5 35 19 (lb) 8.35 12.28 2.28 5.12 3.23 4 2-1/2–8 4.45 0.95
1 Ton 252010
mm 76–203 127–622 1000 15 (kg) 252 330 75 155 102 118 76–203 128 30.5
in. 3–8 5–24.5 39 33 (lb) 9.92 13 2.95 6.10 4 4.65 3–8 5.04 1.20
1-1/2 Ton 252015
mm 82–203 153–622 1100 18.5 (kg) 281 336 85 162 115 124 82–203 145 33
in. 3-1/4–8 6–24.5 43 41 (lb) 11.06 13.23 3.35 6.38 4.53 4.88 3-1/4–8 5.71 1.3
2 Ton 252020
mm 82–203 153–622 1100 23 (kg) 302 350 90 170 127 137 82–203 152 36
in. 3-1/4–8 6–24.5 43 51 (lb) 11.89 13.78 3.54 6.69 5 5.40 3-1/4–8 5.98 1.42
3 Ton 252030
mm 102-203 203–622 1300 37.5 (kg) 346 370 110 217 147 157 102–203 186 45
in. 4–8 8–24.5 51 83 (lb) 13.62 14.57 4.33 8.54 5.79 6.18 4–8 7.32 1.77
5 Ton 252050
mm 117-203 254–622 1400 54.5 (kg) 382 400 122 255 160 172 117–203 219 60
in. 4-5/8–8 10–24.5 55 120 (lb) 15.04 15.75 4.80 10.04 6.30 6.77 4-5/8–8 8.62 2.36
10 Ton 252060
mm 120-203 254–622 1700 92 (kg) 455 432 151 295 189 200 120–203 275 82
in. 4-3/4–8 10–24.5 67 202 (lb) 17.91 17 5.94 11.61 7.44 7.87 4-3/4–8 10.83 3.23
Index
No Part No Description Qty
1 ......1/2GBT-23 ...... Split Pin (1/2 ton) ...................... 2
........1GBT-23......... Split Pin (1 ton) ......................... 2
........2GBT-23......... Split Pin (2 ton) ......................... 2
........3GBT-23......... Split Pin (3 ton) ......................... 2
........5GBT-23......... Split Pin (5 ton) ......................... 2
........10GBT-23 ....... Split Pin (10 ton) ....................... 2
2 ......1/2GBT-26 ...... Nut (1/2 ton) ............................. 2
........1GBT-26......... Nut (1 ton) ................................ 2
........2GBT-26......... Nut (2 ton) ................................ 2
........3GBT-26......... Nut (3 ton) ................................ 2
........5GBT-26......... Nut (5 ton) ................................ 2
........10GBT-26 ....... Nut (10 ton) .............................. 2
3 ......1/2GBT-29 ...... Hanger Plate (1/2 ton) ............... 1
........1GBT-29......... Hanger Plate (1 ton) .................. 1
........2GBT-29......... Hanger Plate (2 ton) .................. 1
........3GBT-29......... Hanger Plate (3 ton) .................. 1
........5GBT-29......... Hanger Plate (5 ton) .................. 1
........10GBT-29 ....... Hanger Plate (10 ton) ................ 1
Index
No Part No Description Qty
4 .. 1/2GT-31 ... Adjusting Washer - 8mm (1/2 ton) ..... 14
.... 1GT-31 ...... Adjusting Washer - 8mm (1 ton) ........ 14
.... 2GT-31 ...... Adjusting Washer - 8mm (2 ton) ........ 12
.... 3GT-31 ...... Adjusting Washer - 8mm (3 ton) ........ 10
.... 5GT-31 ...... Adj. Washer - 8mm(10mm)(5 ton) ..... 8
.... 10GT-31 .... Adj. Washer - 8mm(10mm)(10 ton) ... 8
5 .. 1/2GT-32 ... Adj. Washer - 2mm (1/2 ton) ............. 18
.... 1GT-32 ...... Adj. Washer - 2mm (1 ton) ................ 10
.... 2GT-32 ...... Adj. Washer - 2mm (2 ton) ................ 16
.... 3GT-32 ...... Adj. Washer - 2mm (3 ton) ................ 12
.... 5GT-32 ...... Adjusting Washer - 2mm (5 ton) ........ 12
.... 10GT-32 .... Adjusting Washer - 2mm (10 ton) ...... 10
