NSA1124-V01
2025
XDA91RB,92RB,94RB,95RB
XDA SERIES
Preparation
Please read entire manual before installation. Due to the technical nature
of ampliers, it is highly recommended that your amplier is installed by a
professional installer or an authorized dealer.
Before You Start
• Disconnect negative battery terminal. (consult a qualied technician for
instructions)
• Avoid installing the amplier where it would be subject to high temperatures, such
as from direct sunlight, or where it would be subject to dust, dirt or excessive
vibration.
• Use extreme caution when drilling holes to avoid damaging fuel lines or existing
vehicle wiring.
• All amplier installations require power, signal and speaker wires (not included).
• An amplier installation kit (sold separately) is highly recommended to facilitate
the installation. Consult your dealer for recommendations.
Mounting Location
• Choose a mounting location for the amplier. Suggested locations include under a
seat or in the trunk.
• The amplier can be mounted horizontal (recommended) or vertical. For optimum
performance, make sure to provide at least 1" of space around all sides. Do not
mount the amplier under carpets or where airow is restricted.
• Do not install the amplier where it may be exposed to moisture.
• The optimum mounting location varies between vehicles. Remember to test all
amplier functions before completing the nal mounting procedure.
TYPICAL
MOUNTING
METHOD
1
XDA SERIES
18
0
XDA SERIES
NOTE:
Be sure to follow specic instructions included with your amplier installation kit
(not included with this amplier). The information below should be used as a general
guideline only.
Power Wire (+12V)
• Disconnect negative battery terminal before proceeding. Consult a qualied
technician for instructions if you are unsure.
• Plan wire routing before cutting any wires to length. Begin by routing the power
+12V wire from the battery to the amplier location. Use a grommet when running
wires through the rewall or metal openings. Avoid running the power wire near
existing vehicle wiring to prevent induced noise from entering the audio system.
• Use extreme caution when drilling holes to avoid damaging fuel lines or existing
vehicle wiring.
• The +12V wire MUST be fused within 18" of the battery for protection of the vehicle’s
electrical system.
Ground Wire (GND)
• The amplier ground wire should be as short as possible (no more than 36" or
1 meter). Choose a clean unpainted section of metal or the vehicle chassis when
attaching the ground connection. Be sure to clean the area of any dirt or grease.
Remote Turn-on Wire (REM)
• The remote turn-on wire connects to the head unit's amplier turn-on lead or
power antenna output.
Speaker Wires
• Choose adequate gauge speaker wire depending on your exact amplier/speaker
combination. Be sure to observe polarity when connecting.
• Do not ground any speaker wires or connect any speaker wires together.
Input Signal
• The amplier's input signal connects to the head unit's low level (RCA) or high level
(speaker wire) outputs.
• Low level input signals deliver the best performance. If unavailable, use the high
level inputs - when interfacing with factory head unit for instance.
Power / Protect Indicators
• Colored LED indicators illuminate from the plastic power terminal.
• The blue LED illuminates during normal operation (POWER) and the red
LED indicator is visible when the amplier detects a fault ( PROTECT).
CAUTION
• Do not use both low and high
level inputs at the same time. Connect only one or the
other.
• Keep low level inputs away from any power wires to avoid engine noise.
• Never run any wires underneath or outside the vehicle.
Connection Descriptions
2
Notes
XDA SERIES
17
Audio Inputs and Controls
XDA91RB
XDA92RB
XDA SERIES
3
XDA SERIES
16
FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following
two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
Warning: Changes or to this unit not expressly approved
by the party responsible for compliance could void the user’s authority to
operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection
against
harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television
reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/amp technician for help.
FRO NT
LEFT
FRON T
LEFT
REAR
LEFT
FRO NT
RIGHT
FRON T
RIGH T
REAR
RIGH T
REA R
RIGHT
REA R
LEFT
FR ONT
RE AR
XDA94RB
High-Level Inputs(Speaker Wire)
Crossover Control
Frequency
XDA SERIES
15
XDA SERIES
Power and Speaker Connections
4
XDA95RB
XDA91RB
Limited One Year* Warranty
from state to state. Jensen warrants this product to the original purchaser to be free
from defects in material and workmanship for a period of one year from the date of the
original purchase. Jensen agrees, at our option, during the warranty period, to repair
any defect in material or workmanship or to furnish an equal new, renewed, or
comparable product (whichever is deemed necessary) in exchange without charges,
Subsequent replacement products are warranted for the balance of the original
warranty period.
What is covered? This warranty covers all defects in the material and workmanship in
this product. The following are not covered: software, installation/removal costs, damage
installation,incorrect line voltage, unauthorized repair, or failure to follow instructions
supplied with the product, or damage occurring during return shipment of the product.
www.jensenmobile.com.
Warranty Coverage
* Limited 1-year warranty. (Proof of purchase required)
Extend your warranty from 1 year to 3 years when you register online at
www.jensenmobile.com.
What to do?
1. Before you call for service, check the troubleshooting guide in your owner's
manual. A slight adjustment of any custom controls may save you a service call.
2. If you require service during the warranty period, you must carefully pack the
product (preferably in the original package) and ship it by prepaid transportation
with a copy of the original receipt from the retailer to an authorized service center.
3. Please describe your problem in writing and include your name, a return UPS
shipping address (P.O. Box not acceptable), and a daytime phone number with your
shipment.
4. For more information and for the location of the nearest authorized service center
please contact us by one of the following methods:
• Call us toll-free at (888) 921-4088
(Monday-Friday, 9:00 am, to 5:00 pm, EST)
• E-mail us at [email protected]
Exclusion of Certain Damages: This warranty is exclusive and in lieu of any and all
other warranties, expressed or implied, including without limitation the implied
liability, right, claim or remedy in contract or tort, whether or not arising from the
company's negligence, actual or imputed. No person or representative is authorized
to assume for the company any other liability in connection with the sale of this product.
In no event shall the company be liable for indirect, incidental, or consequential damages.
FRO NT
LEFT
F/R
FRO NT
RIGHT
50H z
40H z
MIN MAX
150 Hz
250 Hz
REA R
RIGHT
REA R
LEFT
SUB
RIGHT
SUB
LEF T
SUB GAIN SUB LPF
SUB SIGNAL
FR ONT
RE AR
X- OVER
X- OVER
Audio Inputs and Controls
BAT
Line In/Line Out (RCA)
Crossover Control
Sub Remote Control Input
Frequency
Power and Speaker Connections
XDA SERIES
5
XDA SERIES
14
XDA92RB
XDA94RB
XDA95RB
Problem Cause Action
Unit will not turn on
(no power LED
indicator)
+12V wire not connected or incorrect
voltage. REM wire not connected or
incorrect voltage
Check connections for proper voltage
(11~16VDC)
GND wire not connected Check connection to ground
Fuse(s) blown Replace fuse(s)
Unit has power -
LED is green (but
no sound)
Speaker wires not connected Check connections at speakers
Volume turned all the way down Increase volume level at head unit
One or more speaker wires touching
each other or touching chassis ground
Insulate all bare speaker wires from
each other and chassis ground
Speaker(s) defective or damaged Check/replace speaker(s)
Input signal not connected
Check high or low level inputs for
proper connection
Unit blows fuse(s)
Incorrect fuse rating Use fuse(s) with correct rating
+12V wire touching chassis ground Check for pinched wire
Speaker(s) defective or damaged Check/replace speaker(s)
Engine noise
Bad ground connection
Make sure amplier is grounded to
clean bare metal
Signal ground loop or RFI (radio
frequency interference)
Re-route RCA cables from existing high
curr
ent wiring
LED illuminates red
(protect mode)
One or more speaker wires touching
each other or touching chassis ground
Insulate all bare speaker wires from
each other and chassis ground
Speaker(s) defective or
damaged internally (shorted)
Check/replace speaker(s)
Speaker load less than 2 ohms (stereo).
Speaker load less than 4 ohms (bridged)
Adjust speaker load - amplier will
not operate at less than 4 ohms when
bridged
Distorted audio
output
Incorrect input signal type or
input level too high
Check connections and reduce/adjust
input level
Low audio output
Incorrect input signal type or
input level too low
Check connections and increase/adjust
input level
Troubleshooting
Front L(+)
Front L(-)
Front R(+)
Front R(-)
Rear L(+)
Rear L(-)
Rear R(+)
Rear R(-)
Sub(+)
Sub(-)
BLU E-P OWE R
RED -PR OTE CT
Front L(+)
Rear L(+)
Front L(-)
Rear L(-)
Front R(+)
Rear R(+)
Front R(-)
Rear R(-)
XDA SERIES
13
XDA SERIES
6
Specifications Typical Wire Routing
XDA91RB
XDA95RB
• Jensen DSP Amp app (Apple
• RGB Custom color illumination
• Class D design
• Low level inputs (RCA)
• Variable gain adjustment (200 mV ~ 6 V)
• Selectable crossover (high pass/low pass/full range)
• Variable low-pass crossover (50 Hz – 150 Hz)
• Variable high-pass crossover (40 Hz – 250 Hz)
• Bass control
• PWM MOSFET power supply
• 2 Ohm stable operation
• Recommended power/ground wire: 4 AWG
• Recommended speaker wire: 12 AWG
• Fuse: 40 A x 2
• Amplifier dimensions: 2.11” x 11.00” x 5.63” (HxDxW)
• Continuous Power Output (1% THD+N):
• 70 Watts RMS x 4 channels + 240 Watts RMS x 1 channel @ 4 ohms
• 100 Watts RMS x 4 channels + 350 Watts RMS x 1 channel @ 2 ohms
• 200 Watts RMS x 2 channels + 240 Watts RMS x 1 channel @ 4 ohms (bridged)
• Maximum dynamic power: 1500 Watts
• THD+N: <0.15% @ 1 Watt RMS
• Frequency response: 20Hz - 20kHz, 20Hz ~ 150Hz
• Signal to noise ratio 68 dBA (reference: 1 Watt RMS @ 4ohm)
/Android™) to control illumination
Typical Wire Routing
XDA92RB
XDA95RB
XDA SERIES
7
XDA SERIES
XDA91RB
XDA92RB
XDA94RB
12
Specifications
• Jensen DSP Amp app (Appl
e
/Android™) to control illumination
• RGB Custom color illumination
• Class D design
• Adjustable bass boost at 40 Hz
• Inputs: High (speaker wire) and Low (RCA) level
• Gain adjustment: 200 mV ~ 6 V
• Built-in crossover
• Adjustable low-pass crossover: 50 Hz – 150 Hz
• Power terminal connector: 4 - 8 AWG
• Speaker terminal connector: 12 - 16 AWG
• Fuse size: 30A x 2
• Amplifier dimensions: 2.11" x 8.25" x 5.63" (HxWxD)
• 240 Watts RMS x 1 channel @ 4 ohms
• 400 Watts RMS x 1 channel @ 2 ohms
• 600 Watts RMS x 1 channel @ 1 ohm
• Total dynamic power: 1,200 Watts
• Frequency response: 20 Hz ~ 150 Hz
• Jensen DSP Amp app (Apple
®
/Android™) to control
illumination
• RGB Custom color illumination
• Class D design
• 2 Ohm stable stereo operation
• Bridgeable operation for subwoofer applications
• Adjustable bass boost at 50 Hz
• Inputs: High (speaker wire) and Low (RCA) level
• Gain adjustment: 200 mV ~ 6 V
• Built-in crossover
• Adjustable high and low-pass crossovers: 30 Hz – 320 Hz
• Power terminal connector: 4 - 8 AWG
• Speaker terminal connector: 12 - 16 AWG
• Fuse size: 25 A
• Amplifier dimensions:
2.11" x 6.44" x 5.63" (HxWxD)
• 80 Watts RMS x 2 channels @ 4 ohms
• 120 Watts RMS x 2 Channels @ 2 Ohms
• 240 Watts RMS x 1 channel @ 4 ohms (bridged)
• Total dynamic power: 600 Watts
• Frequency response: 20 Hz ~ 20 kHz
• Signal to noise ratio 68 dBA
(reference: 1 Watt into 4 ohms)
• Jensen DSP Amp app (Apple
®
/Android™) to control illumination
• RGB Custom color illumination
• Class D design
• 2 Ohm stable stereo operation
• Bridgeable operation for subwoofer applications
• Adjustable bass boost at 50 Hz
• Inputs: High (speaker wire) and Low (RCA) level
• Gain adjustment: 200 mV ~ 6 V
• Built-in crossover
• Adjustable high and low-pass crossovers: 30 Hz – 320 Hz
• Power terminal connector: 4 - 8 AWG
• Speaker terminal connector: 12 - 16 AWG
• Fuse size: 25 A x 2
• Amplifier dimensions:
2.11" x 8.78" x 5.63" (HxWxD)
• 80 Watts RMS x 4 channels @ 4 ohms
• 120 Watts RMS x 4 channels @ 2 ohms
• 240 Watts RMS x 2 channels @ 4 ohms (bridged)
• Total dynamic power: 1,000 Watts
• Frequency response: 20 Hz ~ 20 kHz
®
• Wired Bass Remote Included
Typical Wire Routing
XDA94RB
XDA SERIES
11
XDA SERIES
8
Bluetooth Pairing With RGB Control
1
2
3
1
2
3
Step 1. Touch the BT icon
Step 2. Touch the Scan icon to search the amp.
1). 5Channel Amp Device Name: Jensen95
2). 4Channel Amp Device Name: Jensen94
3). 2Channel Amp Device Name: Jensen92
4). 1Channel Amp Device Name: Jensen91
Step 3. Amp list to show what amp is paired. (If only one amp is installed,
one amp model number is displayed.
Step 4. Select the amp model number you want.
Step 5. RGB Control Screen is displayed, and RGB Colors can be controlled.
Step 6. After the rst time Bluetooth pairing, RGB Control screen is displayed
automatically when the App is opened.
Input Signal Connections
Low Level Input (RCA)
Low level (RCA) input signal is preferred for best performance. Typical trunk-mount
amplier installations require a 17-20 foot RCA cable. Most trucks and under-seat
applications require a 6-9 foot RCA cable. Using twisted pair construction RCA
cables will minimize noise.
Speaker Connections
Connect speaker wires
observing polarity. The
minimum impedance load
for the ampliers is 2 ohms
stereo and 4 ohms bridged.
Use of loads lower than these
is not recommended and may
cause amplier damage. The
ampliers can be wired for
stereo, bridged or stereo/
bridged simultaneous
operation.
Note: Do not use both low and high level inputs
at the same time - connect only one or the other.
Amplifier Connections
Low-Level Input
(RCA)
High Level Input
(Speaker Wire)
High level inputs should only be used
when RCA outputs are not available from
the head unit. Connect the head unit
speaker outputs to the high level input
connector as shown below. The black wire
(signal reference ground) may or may not
require a connection to chassis ground -
depending on your particular installation.
Typical speaker connections show n
Speakers (bridged)
Typical Bridged Wiring
(4 ohms minimum)
2 Speakers (stereo)
Typical Stereo Wiring
(2 ohms minimum)
XDA SERIES
Scan the above QR Code to download the Jensen Octane DSP Amplier
Controller app from the Apple App Store or Google Play Store onto your
smartphone or tablet.
Use the app to control
RGB color customization only directly from your
Note:
XDA amp series do not support audio streaming and hands free
calls via Bluetooth.
App
Download/Installation For RGB Colors
9
XDA SERIES
10
smartphone or tablet via Bluetooth.
