INDUCTION COOKTOPS
HCI905FTB4, HCI905FTG4, HCI905TPB4, HCI905TB4,
HCI604FTB4, HCI604FTPB4, HCI604FTG4
Induction Cooktops
INSTALLATION GUIDE NZ AU
2
CONTENTS
Safety and warnings ................................................................................4
Components required .............................................................................7
Product specifications
HCI905FTB4, HCI905FTG4, HCI905TPB4, HCI905TB4
..............................8
HCI604FTB4, HCI604FTPB4, HCI604FTG4 ...............................................9
Cavity specification............................................................................... 10
Clearances ........................................................................................... 11
Ventilation............................................................................................ 12
Electrical specifications ......................................................................... 13
Installation ........................................................................................... 15
Installer checklist .................................................................................. 17
3
WARNING!
Electric Shock Hazard
Failure to follow this advice may result in
electric shock or death.
• Disconnect the appliance from the mains
electricity supply before carrying out any work
or maintenance.
• Connection to a good earth wiring system is
essential and mandatory.
• Alterations to the domestic wiring system must
only be made by a qualified electrician.
• Do not cook on a broken or cracked cooktop. If
the cooktop surface should break or crack, switch
the appliance off immediately at the mains power
supply (wall switch) and contact a qualified
technician.
WARNING!
Cut Hazard
Failure to use caution could result in injury.
• Take care: some edges are sharp.
• The razor-sharp blade of a cooktop scraper is
exposed when the safety cover is retracted. Use
with extreme care and always store safely and out
of reach of children.
SAFETY AND WARNINGS
4
SAFETY AND WARNINGS
WARNING!
Hot Surface Hazard
Failure to follow this advice may result in
burns and scalds or serious injury.
• During use, accessible parts of this appliance
will become hot enough to cause burns.
• Do not let your body, clothing or any item other
than suitable cookware contact the ceramic
glass until the surface is cool.
• Metallic objects such as knives, forks, spoons
and lids should not be placed on the hob
surface since they can get hot.
• Handles of saucepans may be hot to touch.
Check saucepan handles do not overhang other
cooking zones that are on. Keep handles out of
reach of children.
• Keep children away.
5
READ AND SAVE THIS GUIDE
General Use
z
Read these instructions carefully before installing this product.
z
Never leave the appliance unattended when in use. Boil over causes smoking and greasy spillovers
that may ignite.
z
Never use your appliance as a work or storage surface.
z
Never leave any objects or utensils on the appliance.
z
Never use your appliance for warming or heating the room.
z
After use, always turn off the cooking zones and the cooktop as described in this manual (i.e. by using
the touch controls).
z
Do not allow children to play with the appliance or sit, stand, or climb on it.
z
Do not store items of interest to children in cabinets above the appliance. Children climbing on the
cooktop could be seriously injured.
z
Do not leave children alone or unattended in the area where the appliance is in use.
z
Children or persons with a disability or lack of experience and knowledge, which limits their ability to
use the appliance should have a responsible and competent person to instruct them in its use. The
instructor should be satisfied that they can use the appliance without danger to themselves or their
surroundings.
z
Do not repair or replace any part of the appliance unless specifically recommended in the manual. All
other servicing should be done by a qualified technician.
z
Do not use a steam cleaner to clean your cooktop.
z
Do not place or drop heavy objects on your cooktop.
z
Do not stand on your cooktop.
z
Do not use pans with jagged edges or drag pans across the Ceramic glass surface as this can scratch
the glass.
z
Do not use scourers or any other harsh abrasive cleaning agents to clean your cooktop, as these can
scratch the Ceramic glass.
z
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly
qualified persons in order to avoid a hazard.
z
This appliance is not intended for use by persons (including children) with reduced physical, sensory
or mental capabilities, or lack of experience and knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a person responsible for their safety.
z
Children should be supervised to ensure that they do not play with the appliance.
z
Cleaning and user maintenance shall not be made by children without supervision.
z
The appliance is not intended to be operated by means of an external timer or separate remote-
control system.
z
CAUTION: The cooking process has to be supervised. A short term cooking process has to be
supervised continuously.
Installation
z
The cooktop must be installed by qualified personnel or technicians.
z
Read these instructions carefully before installing or using this appliance.
z
The bench top must be square and level, and no structural members should interfere with space
requirements.
z
The cooktop will not be installed directly above a dishwasher, fridge, freezer, washing machine or
clothes dryer, as the humidity may damage the cooktop.
z
If the cooktop is installed above an oven, the oven must have a built-in cooling fan.
z
The installation will comply with all clearance requirements and applicable standards and regulations.
z
The work surface must be made of a heat-resistant material.
SAFETY AND WARNINGS
6
z
No combustible material or products should be placed on this appliance at any time.
z
Please make this information available to the person responsible for installing the appliance as it could
reduce your installation costs.
z
In order to avoid a hazard, this appliance must be installed according to these instructions for
installation.
z
This appliance should be connected to a circuit which incorporates an isolating switch providing full
disconnection from the power supply.
z
Failure to install the appliance correctly could invalidate any warranty or liability claims.
z
Use heat-resistant and easy-to-clean finishes (such as ceramic tiles) for the wall surfaces surrounding
the hob.
z
Consult local building authorities and by-laws if in doubt regarding installation.
z
To avoid any damage, the foam seal and adhesive must be resistant to heat.
Electrical
z
This cooktop must be connected to the mains power supply only by a suitably qualified person.
z
This cooktop must be earthed by a suitably qualified person.
z
A suitable isolating switch providing full disconnection from the mains power supply is incorporated in
the permanent wiring, mounted and positioned to comply with the local wiring rules and regulations.
z
The isolating switch must be of an approved type and provide a 3 mm air gap contact separation
in all poles (or in all active [phase] conductors if the local wiring rules allow for this variation of the
requirements).
z
Before connecting the cooktop to the mains power supply, check that:
z
The domestic wiring system is suitable for the power drawn by the cooktop
z
The voltage corresponds to the value given on the rating plate
z
The power supply cable sections can withstand the load specified on the rating plate.
z
To connect the cooktop to the mains power supply, do not use adapters, reducers, or branching
devices, as they can cause overheating and fire.
z
The power supply cable must not be kinked and should not be touching the underside of the
cooktop which could get hot during operation.
z
If the cable is damaged or needs replacing, this should be done by an after-sales technician using
the proper tools, so as to avoid any accidents.
z
If the appliance is being connected directly to the mains supply, an omnipolar circuit breaker must
be installed with a minimum gap of 3mm between the contacts.
z
The installer must ensure that the correct electrical connection has been made and that it
complies with safety regulations.
z
The cable must be checked regularly and only replaced by a properly qualified person.
z
The power supply should be connected in compliance with the relevant standard, or a single-pole
circuit breaker. The method of connection is shown below.
Electromagnetic hazards
z
This appliance complies with electromagnetic safety standards.
z
However, persons with cardiac pacemakers or other electrical implants (such as insulin pumps)
must consult with their doctor or implant manufacturer before using this appliance to make sure
that their implants will not be affected by the electromagnetic field.
z
Failure to follow this advice may result in death.
SAFETY AND WARNINGS
7
COMPONENTS REQUIRED
TOOLS
Not supplied
F Box cutter
F Phillips screwdriver
F Level
PARTS
Supplied and required
F 4 x Retaining brackets
F 4 x Bracket screws
F Foam tape (attached)
8
PRODUCT SPECIFICATIONS HCI905FT AND HCI905T MODELS
PRODUCT DIMENSIONS MM
A Overall length of cooktop 900
B Overall width of cooktops 520
C Length of chassis 867
D Width of chassis 487
E Height of chassis (excluding glass) 56
F Height of cooktop glass 4
G Overall cooktop height 60
A
B
C
D
E
F
G
9
PRODUCT SPECIFICATIONS HCI604FT MODELS
A
B
C
D
E
F
G
PRODUCT DIMENSIONS MM
A Overall length of cooktop 590
B Overall width of cooktops 520
C Length of chassis 560
D Width of chassis 490
E Height of chassis (excluding glass) 56
F Height of cooktop glass 4
G Overall cooktop height 60
10
CAVITY SPECIFICATION
PRODUCT DIMENSIONS MIN MAX
HCI905 Models
A Width of cavity 488mm 490mm
B Length of cavity 868mm 870mm
HCI604 Models
C Width of cavity 480mm 492mm
D Length of cavity 560mm 562mm
A
B
C
D
HCI604 Models
HCI905 Models
11
CLEARANCES
Ensure all minimum specifications have been met and clearances have been considered.
B
A
CLEARANCE DIMENSIONS MM
A Minimum clearance from glass surface to rangehood 600
B Minimum clearance below cooktop chassis to any appliance, companion product or
obstruction below cooktop*
50
C Minimum clearance from rear edge of cut-out to nearest combustible surface 50
D Minimum clearance from front edge of cut-out to front edge of counter 50
E Minimum clearance from side edges of cut-out to nearest combustible surface 50
F Minimum bench top thickness 18
*Clearance stated is for proud installation of the cooktop. For flush installations, the height of the cooktop glass should be added to the
clearance.
C
D
E
F
12
VENTILATION
VENTILATION DIMENSIONS MM
A Minimum ventilation gap at the rear of the cooktop 20
B Minimum ventilation gap at the front of the cooktop 5
C Minimum ventilation under the cooktop 50
*If ventilation gap at the rear of the cooktop is not possible, add two x 2” diameter (50mm) holes in the side wall to allow adequate
cooling air.
A
B
C
This cooktop requires adequate supply of cool air to fully function. The base of the cooktop must have
direct unrestricted ventilation to the room where the cooktop is installed. There must be a 5mm air gap at
the front of the cooktop.
Air gap must be no lower than 40mm from the top of
the cooktop.
Drawer or other obstruction
56mm 40mm 30mm
13
ELECTRICAL SPECIFICATIONS
Connecting the cooktop to the mains power supply
IMPORTANT!
z
This cooktop must be connected to the mains power supply only by a suitably qualified
person.
z
This cooktop must be earthed.
z
Before connecting the cooktop to the mains power supply, check that:
z
The domestic wiring system is suitable for the power drawn by the cooktop
z
The voltage corresponds to the value given on the rating plate
z
The power supply cable sections can withstand the load specified on the rating plate.
z
To connect the cooktop to the mains power supply, do not use adapters, reducers, or
branching devices, as they can cause overheating and fire.
z
The power supply cable must not be kinked and should not be touching the underside
of the cooktop which could get hot during operation.
z
If the cable is damaged or needs replacing, this should be done by an after-sales
technician using the proper tools, so as to avoid any accidents.
z
If the appliance is being connected directly to the mains supply, an omnipolar circuit
breaker must be installed with a minimum gap of 3mm between the contacts.
z
The installer must ensure that the correct electrical connection has been made and that
it complies with safety regulations.
z
The cable must be checked regularly and only replaced by a properly qualified person.
z
The power supply should be connected in compliance with the relevant standard, or a
single-pole circuit breaker. The method of connection is shown below.
IMPORTANT!
z
Check with an electrician whether the domestic wiring system is suitable without
alterations. Any alterations must only be made by a qualified electrician.
14
ELECTRICAL SPECIFICATIONS
IMPORTANT!
z
Check with an electrician whether the domestic wiring system is suitable without
alterations. Any alterations must only be made by a qualified electrician.
SINGLE PHASE TWO PHASE
Input
NL
220- 240V
Grey
Black
Brown
Blue
Yellow/Green
Black
Brown
Blue
Yellow/Green
L1
N
L2
400V
220 - 240V
220 - 240V
Input
Grey
Power cord Power cord
15
INSTALLATION
1
Turn the cooktop upside down on a
protective cover.
Do not remove the foam seal
under the edge of the glass top.
2
Fix the four supplied retaining
brackets to cooktop.
Insert the tab into the side of the
cooktop and screw the bracket in.
16
INSTALLATION
3
Connect the cooktop to the mains
power.
Flip the cooktop and lower it into
the bench cut-out.
4
Press the glass edges onto the
bench top.
17
Complete and keep for safe reference:
Model
Serial no.
Purchase date
Purchaser
Dealer address
Installer’s name
Installer’s signature
Installation company
Installation date
INSTALLER CHECKLIST
GENERAL
ELECTRICAL
Read safety and warnings in the user guide before operating the cooktop.
Specified clearance maintained.
Unit is level – front to back and side to side.
All packaging materials have been removed.
There is constant flow of cool air from the cabinetry to the base of the cooktop.
Basic operation has been demonstrated to the customer.
The cooktop is functioning correctly. Turn on all zones to a high setting and leave on
for at least one minute.
Touch controls and displays are functioning.
Receptacle with correctly rated over-current protection is provided for service
cord connection.
Adequate ground connection.
Power supply cable is accessible and is not touching the cooktop.
