BlazeGrills.com
Blaze Appliance Cart
PREMIUM LTE SERIES PRODUCT MANUAL
BLZ-GRIDDLE40-LP/NG
BLZ-4LTEPRO-LP/NG
BLZ-5LTEPRO-LP/NG
SCAN TO REGISTER
2
Blaze Pro Cart
BlazeGrills.com
Do not use power tools to assemble. Only
use hand tools, as power tools can damage
or loosen the nutsert.
M5 x 12 mm M5 x 24 mm
Before getting started:
Unpack and lay out all of the included parts.
Most of the stainless steel pieces come with
a protective film. Remove all of the plastic
film and pay no attention to the print on the
film as it has nothing to do with the assembly
instructions.
Take caution with the stainless steel
components as to not scratch them during
the assembly process. Use a non-aressive
surface and protect the stainless steel as best
as possible. The foam and box can be used to
place the stainless steal parts on to prevent
scratching. - (77) M5 x 12 mm screw will be
paired with a M5 lock washer.
Use M5 flat washer and lock washer for
M5 washer M5 lock washer
Tools Needed: #2 Phillips Head Screw Driver – “Not
Included”
hardware needed "included"
WARNING
CALIFORNIA PROPOSITION 65 WARNING:
This product can expose you to chemicals
including Chromium (hexavalent
compounds), which are known to the State
of California to cause cancer and birth
defects or other reproductive harm. For
more information go to: www.P65Warnings.
ca.gov
installing the casters to the base. All other
connections will be made with a screw only.
NOTE - screws for the door handles are smaller
and those are packaged with the handles them
self.
(2) M5 x 24 mm - are to be used last and are for
securing BBQ to cart.
The appliance is to be placed into the cart
after all instructions have been followed and
all screws have been tightened.
Be sure to place your parts on a protected
surface such as a towel or blanket to prevent
scratching.
3
40" LTE PRO Grill Cart
17.
18.
16.
15.
14.
13.
12.
11.
10.
9.
8.
7.
6.
5.
4.
3.
2.
1.
Blaze Part Number: Reference Guide
15. Back bottom panel
3. Side Shelf
17. Side Shelf bracket
18. light
4. Right side panel
1. Propane drawer
6. Casters
5. Right side drawer slide
9. Right side shelf panel
10. Top side shelf panel
7. Front face
8. Bottom panel
2. Handles
13. Left door
12. Hinges
11. Left side panel
16. Hardware pack
14. Upper back panel
BLZ-D/DR-LED
BLZ-5LTEPROCART-LTSC-002
BLZ-D/DR-2
BLZ-4LTEPROCART-LTSC-001
BLZ-4LTEPROCART-LTSC-004
BLZ-5LTEPROCART-LTSC-001
BLZ-3PROC-003
BLZ-5LTEPROCART-LTSC-003
BLZ-5LTEPROCART-LTSC-004
BLZ-5LTEPROCART-LTSC-005
BLZ-5LTEPROCART-LTSC-006
BLZ-4LTEPROCART-LTSC-010
BLZ-AD32-007
BLZ-5LTEPROCART-LTSC-007
BLZ-5LTEPROCART-LTSC-008
BLZ-5LTEPROCART-LTSC-009
BLZ-CART-HARDWARE
BLZ-3PRO-069
4 Blaze Pro Cart
BlazeGrills.com
40" LTE PRO Griddle Cart
17.
18.
16.
15.
14.
13.
12.
11.
10.
9.
8.
7.
6.
5.
4.
3.
2.
1.
Blaze Part Number: Reference Guide
15. Back bottom panel
3. Side Shelf
17. Side Shelf bracket
18. light
4. Right side panel
1. Propane drawer
6. Casters
5. Right side drawer slide
9. Right side shelf panel
10. Top side shelf panel
7. Front face
8. Bottom panel
2. Handles
13. Left door
12. Hinges
11. Left side panel
16. Hardware pack
14. Upper back panel
BLZ-D/DR-LED
BLZ-GRIDDLE40CART-001
BLZ-D/DR-2
BLZ-GRIDDLE40CART-003
BLZ-GRIDDLE40CART-004
BLZ-GRIDDLE40CART-005
BLZ-3PROC-003
BLZ-GRIDDLE40CART-006
BLZ-GRIDDLE40CART-007
BLZ-GRIDDLE40CART-008
BLZ-GRIDDLE40CART-009
BLZ-GRIDDLE40CART-010
BLZ-AD32-007
BLZ-GRIDDLE40CART-002
BLZ-GRIDDLE40CART-011
BLZ-GRIDDLE40CART-012
BLZ-CART-HARDWARE
BLZ-3PRO-069
5
32" LTE PRO Grill Cart
17.
18.
16.
15.
14.
13.
12.
11.
10.
9.
8.
7.
6.
5.
4.
3.
2.
1.
Blaze Part Number: Reference Guide
15. Back bottom panel
3. Side Shelf
17. Side Shelf bracket
18. light
4. Right side panel
1. Propane drawer
6. Casters
5. Right side drawer slide
9. Right side shelf panel
10. Top side shelf panel
7. Front face
8. Bottom panel
2. Handles
13. Left door
12. Hinges
11. Left side panel
16. Hardware pack
14. Upper back panel
BLZ-D/DR-LED
BLZ-4LTEPROCART-LTSC-002
BLZ-D/DR-2
BLZ-4LTEPROCART-LTSC-001
BLZ-4LTEPROCART-LTSC-004
BLZ-4LTEPROCART-LTSC-005
BLZ-3PROC-003
BLZ-4LTEPROCART-LTSC-006
BLZ-4LTEPROCART-LTSC-007
BLZ-4LTEPROCART-LTSC-008
BLZ-4LTEPROCART-LTSC-009
BLZ-4LTEPROCART-LTSC-010
BLZ-AD32-007
BLZ-4LTEPROCART-LTSC-003
BLZ-4LTEPROCART-LTSC-011
BLZ-4LTEPROCART-LTSC-012
BLZ-CART-HARDWARE
BLZ-3PRO-069
6 Blaze Pro Cart
BlazeGrills.com
STEP 3: Attach the right and left side cart panels.
The right and left side panels can be identified as
follows. The top rail of each side cart panel is a
solid surface with no openings for anything to screw
down into. The bottom sides have three openings
per panel for screws, which are used to attach to the
bottom cart panel. The front side of each cart panel
has a cluster of three nutserts within 1.5 inches
of each other, which will attach to the front strut
assembly. Attach both the left and right side panels
to the bottom cart panel using three screws per
side. Do not completely tighten.
STEP 4: Attach Bottom Back Panel - The bottom back
panel is first secured to the bottom cart panel with
screws. (The bottom of the panel has openings for screws
to go through; see the diagram.) The number of screws
used varies by the size of the grill cart you are assembling.
Attach but do not tighten. Next, secure the bottom
back panel. Attach to side walls before adding top bar.
L
R
STEP 1: Flip the panel upside down on a protected
surface, exposing the four locations where the casters
attach. There are two runners on the bottom cart panel
with four nutserts (female threaded inserts that a screw
goes into) at each end of each runner. This is where the
casters will be installed.
STEP 2: Attach the four casters. Use the locations
described above and tighten them completely. Once
complete, lock the locking casters, then turn the bottom
panel right side up.
For the remainder of the grill cart
assembly, the use of a second person is
recommended to make the process easier.
7
STEP 5: Attach the upper two screws on the back side
panel, but do not fully tighten them until the cart is
fully assembled. Then attach the side panels to the
lower back panel.
STEP 6: Slide the back panel on left and right screws
but located on the side panels do not tighten them let
this panel hang on these screws for now.
STEP 7: Attach the upper shelf panel to the right shelf
STEP 8: Attach the shelf to the interior of the
appliance cart using six screws: three on the interior
of the cart and three on the exterior.
STEP 9: Attach the right-side drawer slide to the lower
right side of the cart.
STEP 10: Slide in the propane pull out.
8 Blaze Pro Cart
BlazeGrills.com
STEP 12: Attach door handles to the doors - The door
handles and hardware are packaged separately from the
rest of the hardware. Each handle is attached to the door
with two M6x8 screws. To avoid scratching the doors,
lay them on a soft surface. Hint: While the door is on a
soft surface on a work area, such as a table, position the
door off the edge just enough to expose the handle screw
holes. Place the screw in your screwdriver and guide it
into the hole on the door. Once positioned, move the
handle to the screw and begin threading it slightly. This
allows flexibility for attaching the second screw. Once
both screws are in place, tighten completely.
STEP 11: Slide the front face of the cart onto the cart,
aligning it with the three holes on each side, and secure
it in place with screws.
STEP 13: To attach the soft-close hinges to the cart, start
by flattening the hinges and loosening the adjustment
screw.
push the hinge
so it lays flat
STEP 14: Then loosen the adjustment screw.
After the hing is layed
flat you can loosen this
screw to allow the
snaps to reach their
snap-on point.
Hinges on
the left
9
STEP 15: Attach the soft-close hinge mounts to the
cart as shown.
Insert two hinge screws
with the rounded hooks
facing toward the back
of the cart.
Back of appliance
cart
STEP 16: To attach the soft-close hinge, snap one
hinge at a time onto the hinge mounts, hooking the
front hook first, then pushing down the back until you
hear a click. This may take multiple tries, and you may
need to loosen the adjustment screw.
.
Pushing this tab while trying to snap the hinge on will
help the hinge have enough clearance to snap into place.
Push this tab down to
allow the hooks on the
hinge to open, making it
easier to hook the hinges
onto their mounts.
snap this
hook first
snap this
hook second
STEP 17 :
Attach the side panel bracket with
the pegs facing outward toward the front of the
appliance cart using 4 screws. Next, slide the
folding side panel onto the bottom peg of this
bracket before securing the second bracket.
10 Blaze Pro Cart
BlazeGrills.com
STEP 19 (Grill Cart): The appliance is placed into the cart
and attached with two screws. Always use a partner when
lifting the appliance, and removing the internal parts
above the burners can help reduce the weight, making
it easier to lift. With the cooking grids still removed, you
will notice an opening toward the front left and right
sides on the inside of the grill body. One screw per side
goes through the inside of the grill and attaches to the
grill cart. Tighten these screws, but do not over-tighten.
STEP 18:
Attach the next side panel bracket with
the pegs facing outward toward the back of
the appliance cart using 4 screws. Ensure that
the bottom peg is inserted into the hole in the
folding side panel before tightening the screws
repeat this process on the other side of the
appliance cart
If you are installing a griddle into your cart the
griddle will not have attachment screws.
STEP 19: (For both griddle and grill) once your
appliance is in place push upper back panel
into the slot on the back of the grill to lock it
in place.
STEP 20: Put locking screws in each side of the
back panel.
STEP 21: Tighten all screws.
11
Please leave these
instructions with the
consumer.
Please read and retain
these instructions for
future reference and
before installation or
operation.
Contact Us:
Blaze
6620 Greenwell Springs Rd
Baton Rouge, LA 70805
Phone: 866-976-9510
customerservice@blazegrills.com
Contact Us:
@Blazegrills
@Blaze_Grills
@BlazeOutdoorProducts
