Hikvision DS-K1T809MWX Value Card Terminal User Manual

DS-K1T809 Series Access Control Terminal

User Manual

Regulatory Informaon

FCC Informaon

Please take aenon that changes or modicaon not expressly approved by the party responsible

for compliance could void the user’s authority to operate the equipment.

FCC compliance: This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable

protecon against harmful interference in a residenal installaon. This equipment

generates, uses and can radiate radio frequency energy and, if not installed and used in accordance

with the

instrucons, may cause harmful interference to radio communicaons. However, there is

no guarantee that interference will not occur in a parcular installaon. If this equipment does

cause harmful interference to radio or television

recepon, which can be determined by turning

the equipment o and on, the user is encouraged to try to correct the interference by one or more

of the following measures:

—Reorient or relocate the receiving antenna.

—Increase the

separaon between the equipment and receiver.

—Connect the equipment into an outlet on a circuit

dierent from that to which the receiver is

connected.

—Consult the dealer or an experienced radio/TV technician for help

This equipment should be installed and operated with a minimum distance 20cm between the

radiator and your body.

FCC

Condions

This device complies with part 15 of the FCC Rules. Operaon is subject to the following two

condions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may cause

undesired

operaon.

DS-K1T809 Series Access Control Terminal User Manual

EU Conformity Statement

This product and - if applicable - the supplied accessories too are marked with "CE"

and comply therefore with the applicable harmonized European standards listed

under the EMC Direcve 2014/30/EU, the RoHS Direcve 2011/65/EU

2012/19/EU (WEEE direcve): Products marked with this symbol cannot be disposed

of as unsorted municipal waste in the European Union. For proper recycling, return

this product to your local supplier upon the purchase of equivalent new equipment,

or dispose of it at designated

collecon points. For more informaon see:

www.recyclethis.info

2006/66/EC (baery direcve): This product contains a baery that cannot be

disposed of as unsorted municipal waste in the European Union. See the product

documentaon for specic baery informaon. The baery is marked with this

symbol, which may include

leering to indicate cadmium (Cd), lead (Pb), or mercury

(Hg). For proper recycling, return the

baery to your supplier or to a designated

collecon point. For more informaon see:www.recyclethis.info

Industry Canada ICES-003 Compliance

This device meets the CAN ICES-3 (B)/NMB-3(B) standards requirements.

This device complies with Industry Canada licence-exempt RSS standard(s).

Operaon is subject to

the following two condions:

1. this device may not cause interference, and

2. this device must accept any interference, including interference that may cause undesired

operaon of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils

radioexempts de licence.

L'exploitaon est autorisée aux deux condions suivantes :

1. l'appareil ne doit pas produire de brouillage, et

l'ulisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage

est

suscepble d'en compromere le fonconnement.

Under Industry Canada regulaons, this radio transmier may only operate using an antenna of a

type and maximum (or lesser) gain approved for the

transmier by Industry Canada. To reduce

potenal radio interference to other users, the antenna type and its gain should be so chosen that

the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful

communicaon.

Conformément à la réglementaon d'Industrie Canada, le présent émeeur radio peut fonconner

avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émeeur par

Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intenon des

autres

ulisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope

DS-K1T809 Series Access Control Terminal User Manual

rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une

communicaon sasfaisante.

This equipment should be installed and operated with a minimum distance 20cm between the

radiator and your body.

Cet équipement doit être installé et ulisé à une distance minimale de 20 cm entre le radiateur et

votre corps.

DS-K1T809 Series Access Control Terminal User Manual

iii

Safety Instrucon

These instrucons are intended to ensure that user can use the product correctly to avoid danger

or property loss.

The

precauon measure is divided into Dangers and Cauons:

Dangers: Neglecng any of the warnings may cause serious injury or death.

Cauons: Neglecng any of the cauons may cause injury or equipment damage.

Dangers: Follow these safeguards to prevent

serious injury or death.

Cauons: Follow these precauons to prevent

potenal injury or material damage.

Dangers

●

All the electronic operaon should be strictly compliance with the electrical safety regulaons,

re prevenon regulaons and other related regulaons in your local region.

●

Please use the power adapter, which is provided by normal company. The power consumpon

cannot be less than the required value.

●

Do not connect several devices to one power adapter as adapter overload may cause over-heat

re hazard.

●

Please make sure that the power has been disconnected before you wire, install or dismantle the

device.

●

When the product is installed on wall or ceiling, the device shall be

rmly xed.

●

If smoke, odors or noise rise from the device, turn

o the power at once and unplug the power

cable, and then please contact the service center.

●

Do not ingest baery, Chemical Burn Hazard.

This product contains a

coin/buon cell baery. If the coin/buon cell baery is swallowed, it

can cause severe internal burns in just 2 hours and can lead to death.

Keep new and used

baeries away from children. If the baery compartment does not close

securely, stop using the product and keep it away from children. If you think baeries might have

been swallowed or placed inside any part of the body, seek immediate medical

aenon.

●

If the product does not work properly, please contact your dealer or the nearest service center.

Never

aempt to disassemble the device yourself. (We shall not assume any responsibility for

problems caused by unauthorized repair or maintenance.)

Cauons

●

This equipment is not suitable for use in locaons where children are likely to be present.

●

Do not drop the device or subject it to physical shock, and do not expose it to high

electromagnesm radiaon. Avoid the equipment installaon on vibraons surface or places

subject to shock (ignorance can cause equipment damage).

DS-K1T809 Series Access Control Terminal User Manual

●

Do not place the device in extremely hot (refer to the specicaon of the device for the detailed

operang temperature), cold, dusty or damp locaons, and do not expose it to high

electromagnec radiaon.

●

The device cover for indoor use shall be kept from rain and moisture.

●

Exposing the equipment to direct sun light, low venlaon or heat source such as heater or

radiator is forbidden (ignorance can cause

re danger).

●

Do not aim the device at the sun or extra bright places. A blooming or smear may occur

otherwise (which is not a

malfuncon however), and aecng the endurance of sensor at the

same

me.

●

Please use the provided glove when open up the device cover, avoid direct contact with the

device cover, because the acidic sweat of the ngers may erode the surface coang of the device

cover.

●

Please use a

so and dry cloth when clean inside and outside surfaces of the device cover, do

not use alkaline detergents.

●

Please keep all wrappers aer unpack them for future use. In case of any failure occurred, you

need to return the device to the factory with the original wrapper.

Transportaon without the

original wrapper may result in damage on the device and lead to addional costs.

●

Improper use or replacement of the

baery may result in hazard of explosion. Replace with the

same or equivalent type only. Dispose of used baeries according to the instrucons provided by

the

baery manufacturer.

●

You can view the device License via the website: hp://opensource.hikvision.com/Home/List?

id=46

DS-K1T809 Series Access Control Terminal User Manual

Available Models

The access control terminal contains the following models:

Product Name Model

Access Control Terminal DS-K1T809MWX

DS-K1T809EWX

DS-K1T809 Series Access Control Terminal User Manual

Contents

Chapter 1 Appearance ................................................................................................................ 1

Chapter 2 Installaon ................................................................................................................. 2

2.1 Installaon Environment ........................................................................................................ 2

2.2 Surface Mounng .................................................................................................................. 2

Chapter 3 Device Wiring ............................................................................................................. 6

3.1 External Device Wiring ........................................................................................................... 6

Chapter 4 Operate on the Device ................................................................................................ 7

4.1 Common Commands ............................................................................................................. 7

4.2 Basic Commands .................................................................................................................... 8

4.2.1

Acvaon ...................................................................................................................... 8

4.2.2 Enter and Exit Programming Mode ............................................................................... 9

4.3 Other Common Commands ................................................................................................. 10

4.3.1 Open Door .................................................................................................................. 10

4.3.2 Set

Funconal Card ..................................................................................................... 11

4.4 Advanced Commands .......................................................................................................... 12

4.4.1 Set Door Parameters ................................................................................................... 12

4.4.2 Set Voice Parameters .................................................................................................. 13

4.4.3 Set NFC ........................................................................................................................ 13

4.4.4 Set Card Reader Wiegand Mode ................................................................................. 13

4.4.5 Restore to Default

Sengs ......................................................................................... 13

4.4.6 Restart Device ............................................................................................................. 14

4.4.7 Restore to Factory

Sengs ......................................................................................... 14

Chapter 5 Congure the Device via the Mobile Web ................................................................. 15

5.1

Acvate via Mobile Web ...................................................................................................... 15

5.2 Login .................................................................................................................................... 15

5.3 Quick Operaon via Web Browser ....................................................................................... 16

DS-K1T809 Series Access Control Terminal User Manual

vii

5.3.1 Time Sengs ............................................................................................................... 16

5.4 Overview .............................................................................................................................. 16

5.5

Conguraon ....................................................................................................................... 17

5.5.1 View Device Informaon ............................................................................................. 17

5.5.2 Time Sengs ............................................................................................................... 17

5.5.3 Set DST ........................................................................................................................ 19

5.5.4 Change Administrator's Password on Mobile Web ..................................................... 19

5.5.5 Network Sengs ......................................................................................................... 20

5.5.6 User Management ...................................................................................................... 21

5.5.7 Search Event ................................................................................................................ 23

5.5.8 Access Control Sengs ............................................................................................... 23

5.5.9 Upgrade and Maintenance ......................................................................................... 27

5.5.10 View Online Document ............................................................................................. 28

Appendix A. Legal Informaon ................................................................................................. 29

Appendix B. Symbol Convenons ............................................................................................. 31

Appendix C. Dimension ............................................................................................................ 32

DS-K1T809 Series Access Control Terminal User Manual

viii

Chapter 1 Appearance

Refer to the following contents for detailed informaon of the access control terminal:

Figure 1-1 Access Control Terminal

Note

The pictures here are for reference only.

DS-K1T809 Series Access Control Terminal User Manual

Chapter 2 Installaon

2.1 Installaon Environment

●

The minimum bearing weight of the wall or other places should be 3 mes heavier than the

device weight.

●

• Please prepare the following tools and accessories: screwdriver (self purchased), screws,

cables, and adapters (self purchased).

2.2 Surface Mounng

Steps

Aach the installaon scker to the wall about 1.45 m from the ground or the locaon where

the device needs to be installed, and punch the hole according to the hole

locaon (hole 1 and

hole 2) on the scker and wall.

Figure 2-1 Installaon Scker

Insert the plasc sleeve of the provided expansion screw into the punched hole.

DS-K1T809 Series Access Control Terminal User Manual

Figure 2-2 Insert Plasc Sleeve

Make sure the cables are threaded through the hole.

Figure 2-3 Thread Cables

Secure the mounng plate on the gang box with two supplied screws (PA4X25-SUS).

DS-K1T809 Series Access Control Terminal User Manual

Figure 2-4 Secure Mounng Plate

Complete the wiring. See the wiring diagram for details.

Figure 2-5 Complete Wiring

Hang the device into the plate from top to boom. Secure the device on the mounng plate

with 1 supplied screw (SC-KM3X6-T10-SUS).

DS-K1T809 Series Access Control Terminal User Manual

Figure 2-6 Secure Device

DS-K1T809 Series Access Control Terminal User Manual

Chapter 3 Device Wiring

3.1 External Device Wiring

Wire the external device.

The wiring diagram is as follows.

Figure 3-1 External Device Wiring

Note

●

Use a DC 12 V power supply. Do not connect the device directly to the 220 V mains.

●

The suggested external power supply for door lock is 12 V, 1 A.

DS-K1T809 Series Access Control Terminal User Manual

Chapter 4 Operate on the Device

4.1 Common Commands

Table 4-1 Common Commands Descripon

Module Operaon Command Descripon

Acvate Device Acvate [*][0][#] [Programming

Password (6 to 8

Digits )] [Repeat

Programming

Password (6 to 8

Digits) ] [#]

The 6 to 8 digits

programming

password cannot all be

Programming Mode Enter Programming

Mode

[Programming

Password (6 to 8

Digits )] [*][0][#]

Go back to

Programming Mode

[*] /

Exit Programming

Mode

[*] [#] The device will

automacally exit the

programming mode

aer 30s of no

operaon.

Change Programming

Password

[00] [New

Programming

Password (6 to 8

Digits )] [Repeat New

Programming

Password (6 to 8

Digits) ] [#]

Add Door Opening

Credenal

Set Door Opening

Password

[03] [Door Opening

Password (4 to 8

Digits )] [Repeat Door

Opening Password (4

to 8 Digits) ] [#]

Add User Card [01] [User Code (4

Digits )](Oponal)

[Swipe Card]...

If you choose to add a

user code, you can

DS-K1T809 Series Access Control Terminal User Manual

Module Operaon Command Descripon

save the added card to

the user code locaon.

Delete User Card [02] [Swipe Card]... /

Add User Cards in

Batch

[01] [User Code (4

Digits )](Oponal)

[Swipe Card 1][Swipe

Card 2][Swipe Card

3]...

Delete User Cards in

Batch (Method 1)

[02] [Swipe Card 1]

[Swipe Card 2][Swipe

Card 3]...

Delete User Cards in

Batch (Method 2)

[15] [Programming

Password (6 to 8

Digits )] [#]

Delete User Code [02] [User Code] [#] /

Delete User Codes in

Batch

[02] [User Code] [#]

[User Code] [#]...

4.2 Basic Commands

The device needs to be acvated before it can be used. Aer acvang, the device can be at two

modes: normal mode and programming mode. Aer entering programming mode, the device can

be operated by commands.

4.2.1

Acvaon

Command

Acvate: [*][0][#] [Programming Password (6 to 8 Digits )] [Repeat Programming Password (6 to 8

Digits) ] [#].

Note

The 6 to 8 digits programming password cannot all be 0.

DS-K1T809 Series Access Control Terminal User Manual

Prompts Descripon

Indicator Prompt Audio Descripon

Light is solid green. The buzzer rings for 3 s. Acvated , and in normal mode

(not programming mode).

Light ashes red slowly for 3

mes.

The buzzer rings for 5 mes

quickly.

Acvang failed.

Light ashes orange slowly. / Inacvated

4.2.2 Enter and Exit Programming Mode

There are two ways to enter the programming mode: enter the command , or directly swipe the

funconal card (including management card, adding card and deleng card).

Programming Mode Command

Enter Programming Mode: [Programming Password (6 to 8 Digits )] [*][0][#].

Exit Programming Mode: [*] [#].

Change Programming Password: [00] [New Programming Password (6 to 8 Digits )] [Repeat New

Programming Password (6 to 8 Digits) ] [#].

Table 4-2 Prompts

Descripon

Indicator Prompt Audio Descripon

Light is solid green for 2 s. The buzzer rings 2 mes quickly. Enter Programming Mode

Light is solid red for 2 s. The buzzer rings 3 mes slowly. Entering Programming Mode failed

/ The buzzer beeps 1 sound. Swipe Card and Press Buon Prompt

Audio

/ The buzzer rings 2 mes. Exit due to meout.

Note

●

Aer 5 consecuve programming password input errors, the device will enter a locked status.

Aer waing for 1800 s or aer the device losing power me cleared, you can enter the

programming password again to enter the programming mode. Enter the programming

password in the locked status, the indicator will be solid orange for 2 s, and the buzzer will ring 5

mes quickly, indicang that it cannot enter the programming mode.

●

In programming mode, "*" represents a fallback to programming mode without entering a

command, and "# "Indicates the end or compleon of a command.

●

In programming mode, you need to press "*" to exit the batch

addion and deleon mode.

DS-K1T809 Series Access Control Terminal User Manual

Swipe Funconal Card

Aer swiping the funconal card in the card swiping area, you can directly enter the programming

mode. See Set Funconal Card for adding details.

4.3 Other Common Commands

4.3.1 Open Door

There are two ways to open door: enter the password, or swipe user card.

Prompts

Descripon

Indicator Prompt Audio Descripon

Light is solid green for 2 s. The buzzer rings 2 mes quickly. Authencated

Light is solid red for 2 s. The buzzer rings 3 mes slowly. Authencaon failed.

/ The buzzer beeps 1 sound. Swipe Card and Press Buon Prompt

Audio

/ The buzzer rings 2 mes. Exit due to meout.

Set Door Opening Password

You can set the door opening password and open door by entering the door opening password.

Command

Command of Seng Door Opening Password: [03] [Door Opening Password (4 to 8 Digits )]

[Repeat Door Opening Password (4 to 8 Digits) ] [#].

Note

The 4 to 8 door opening password cannot all be 0. If all of them are 0, the door opening password

funcon will be disabled.

Add/Delete User Card

Command

Add User Card: [01] [User Code (4 Digits)] (Oponal)[Swipe Card ]...

DS-K1T809 Series Access Control Terminal User Manual

Add User Card in Batch:[01] [User Code (4 Digits )](Oponal) [Swipe Card 1][Swipe Card 2][Swipe

Card 3]...

Note

●

If you enter a user code before adding a card, the locaon of the added user card is under this

code ID, and if you do not enter the user code, the added card has no xed posion.

●

The user code format is 4 digits and the range is from1 to 1000. If the entered code content and

format is incorrect, the

addion fails, and the current adding command ends.

Delete User Code: [02] [User Code] [#].

Delete User Code in Batch: [02] [User Code] [#][User Code] [#]...

Delete User Card: [02] [Swipe Card].

Delete User Card in Batch (Method 1): [02] [Swipe Card 1] [Swipe Card 2][Swipe Card 3]...

Delete User Card in Batch (Method 2): [15] [Programming Password (6 to 8 Digits )] [#].

4.3.2 Set

Funconal Card

Funconal cards include management card, adding card and deleng card.

Note

Funconal cards cannot be used to open door, but are only equivalent to a certain command.

Management Card

Swipe the management card in the standby status: it means that the device directly enters the

programming mode, and there is no need to enter the command to enter the programming mode.

Command of Adding Management Card: [04] [Swipe Card].

Command of

Deleng Management Card: [05][#].

Command of Adding Management Card, Adding Card and Deleng Card at Once: [10] [Swipe

Management Card][Swipe Adding Card] [Swipe

Deleng Card].

Note

Aer swiping the management card to enter the programming mode, if the device is not operated

for 30 s, it will exit programming mode. Swipe twice in 3 seconds to switch door contact sengs.

When switching the door contact, the buzzer ringing 8 mes slowly means that the mode is

switched to remain closed, and the buzzer ringing 8

mes quickly means that the mode is switched

to remain open.

Adding Card

Swipe the adding card in the standby status: it means that the device directly enters the

programming mode, and enters the [01] command (adding command).

For example, if you need to add a user card, you can swipe the adding card and then swipe a user

card when the device is in standby status.

DS-K1T809 Series Access Control Terminal User Manual

Command of Adding Adding Card: [06] [Swipe Card].

Command of Deleng Adding Card: [07][#].

Note

Aer swiping the adding card to enter the programming mode, if the device is not operated for 30

s, it will exit programming mode.

Delete Card

Swipe the deleng card in the standby status: it means that the device directly enters the

programming mode, and enters the [02] command (deleng command).

For example, if you need to delete a user card, you can swipe the

deleng card and then swipe a

user card when the device is in standby status.

Command of Adding Deleng Card: [08] [Swipe Card].

Command of

Deleng Deleng Card: [09][#].

Note

Aer swiping the deleng card to enter the programming mode, if the device is not operated for

30 s, it will exit programming mode.

4.4 Advanced Commands

4.4.1 Set Door Parameters

The door opening me, door opening meout, door contact type and exit buon type can be set

by command.

Command: [11] [Data Bit 1] [Data Bit 2] [Data Bit 3] [Data Bit 4] [#].

Data Bit 1: Indicates the door opening

me, which is a three digits number from 000 to 255. The

unit is second. If the door opening

me is 3 s, the data bit 1 is set to 003. The default door opening

me is 5 s.

Data Bit 2: Indicates the door opening

meout, which is a two digits number. The unit is second. If

the door is opened beyond this seng me, the device will alarm and ring for 10 s. If you enter

"50", the alarm me for door opening meout will be 50 s. The default door opening meout is 30

Data Bit 3: Indicates the type of door contact, which is a one digit number. "0" means remaining

closed, and "1" means remaining open. It is remaining closed by default.

Data Bit 4: Indicates the type of exit

buon, which is a one digit number. "0" means remaining

closed, and "1" means remaining open. It is remaining closed by default.

DS-K1T809 Series Access Control Terminal User Manual

4.4.2 Set Voice Parameters

You can set whether to enable the buon sound and authencaon prompt audio through the

command.

Command: [12] [Data Bit 1] [Data Bit 2] [#].

Data Bit 1: Indicates whether to enable the

buon sound, which is a one digit number. "0" means

the

buon sound is disabled, and "1" means the buon sound is enabled. It is enabled by default.

Indicates whether to enable the

authencaon prompt audio, which is a one digit number. "0"

means the

authencaon prompt audio is disabled, and "1" means the authencaon prompt

audio is enabled. It is enabled by default.

Note

The disabling only takes eect in the normal mode, not in the programming mode.

4.4.3 Set NFC

You can set whether to enable NFC funcon through the command.

Command: [13] [Data Bit 1] [#].

Data Bit 1: “0" means disabling NFC

funcon, and "1" means enabling NFC funcon. It is enabled

by default.

Note

Only some models support this funcon, please refer to the actual product.

4.4.4 Set Card Reader Wiegand Mode

The Wiegand mode of card reader can be set by command.

Command: [14] [Data Bit 1] [#].

Data Bit 1: "0" means Wiegand 26 mode, and "1" means Wiegand 34 mode. The default mode is

Wiegand 34.

4.4.5 Restore to Default

Sengs

You can perform commands or press buon to restore to default sengs.

Command 1: [16] [Programming Password (6 to 8 Digits )]] [#] (Only Restore Data Except User

Cards Data).

Command 2: Press and hold the "*"

buon for 5 seconds within 30 seconds of powering on.

DS-K1T809 Series Access Control Terminal User Manual

4.4.6 Restart Device

You can restart the device by command.

Command: [17] [Programming Password (6 to 8 Digits )] [#].

4.4.7 Restore to Factory Sengs

You can restore the device to factory sengs by command.

Command: [18] [Programming Password (6 to 8 Digits )]] [#] (Restore All User and Default Data).

DS-K1T809 Series Access Control Terminal User Manual

Chapter 5 Congure the Device via the Mobile Web

The device supports acvaon and operaon through device-side commands. It also supports

acvaon and operaon on the mobile phone by connecng to the device hotspot. (If it is

acvated through the mobile phone, it cannot be operated through the device. If it is acvated

through the device, you can operate on the mobile phone. ）

5.1 Acvate via Mobile Web

You can acvate the device via mobile web.

Steps

Aer the device is powered on, the hotspot is enabled by default. Search for and connect to the

device hotspot on your phone.

Note

●

Device hotspot name is AP_ Serial No., and inial password of device hotspot is Serial No.

Aer restarng or switching from non-AP mode to AP mode aer acvaon (press and hold

the number buon 5 to switch AP mode), the hotspot password will be changed to the

acvaon password.

●

You can log in to the mobile web client only when the device is in AP mode.

Open the browser address bar of the mobile phone and enter 192.168.8.1 to enter the

acvaon interface.

Set the

acvaon password and conrm it.

Note

●

The password must be 8 to 16 characters long.

●

The password must be composed of two or more combinaons of numbers, lowercase leers,

uppercase leers, and special characters.

●

The password cannot contain the user name, 123, admin, 4 or more

consecuve digits in

increments or decrement, or the same symbol.

Tap Acvate Device.

5.2 Login

You can log in via mobile browser.

Note

●

Parts of the device models support this funcon.

●

Make sure the device is acvated.

DS-K1T809 Series Access Control Terminal User Manual

Enter the device IP address in the address bar of the mobile browser and press Enter to enter the

Enter the device user name and the password. Tap Login.

5.3 Quick Operaon via Web Browser

5.3.1 Time Sengs

You can set the me zone, me synchronizaon mode, and the displayed me.

Device Time

Display the device me in real me.

Time Zone

Select the device located me zone from the drop-down list.

Time Synchronizaon Mode

NTP

You should set the NTP server's IP address, port No., and interval.

Manual

By default, the device

me should be synchronized manually. You can set the device me

manually or check Sync. with Phone Time to synchronize the device me with the phone's

me.

DST

You can enable DST, set and view the DST start

me, end me and bias me.

Click Next to save the sengs.

5.4 Overview

You can view the door status, network status and basic informaon, and set person management,

authencaon sengs, and door parameters via shortcut entry.

Funcon Descripons:

Door Status

/ / /

The door status is open/closed/remaining open/remaining closed. You can tap to select

open/closed/remaining open/remaining closed status according to your actual needs.

Shortcut Entry

You can set person management, authencaon sengs, and door parameters via shortcut

entry.

DS-K1T809 Series Access Control Terminal User Manual

Network Status

You can view the connected status of wireless network and Hik-Connect.

Basic Informaon

You can view the model, serial No. and rmware version.

5.5 Conguraon

5.5.1 View Device Informaon

View the device name, language, model, serial No., version, number of channels, IO input number,

number of alarm input and output, Mac address, factory

informaon and device capacity, etc.

Tap → System Sengs → Basic Informaon to enter the conguraon page.

You can view the device name, language, model, serial No., version, number of channels, IO input

number, number of alarm input and output, Mac address, factory

informaon and device capacity,

etc.

5.5.2 Time

Sengs

Set the me zone, me sync. mode, and displayed me.

Tap → System Sengs → Time Sengs to enter the sengs page.

DS-K1T809 Series Access Control Terminal User Manual

Figure 5-1 Time Sengs

Tap Save to save the sengs.

Time Zone

Select the me zone where the device is located from the drop-down list.

Time Sync. Mode

Manual

You can set the device me manually, or enable Sync. with Phone Time.

NTP

DS-K1T809 Series Access Control Terminal User Manual

Set the NTP server's IP address, port No., and interval.

5.5.3 Set DST

Steps

Tap

→ System Sengs → Time Sengs , to enter the sengs page.

Figure 5-2 DST

Tap Enable DST.

Set the start

me, end me, and DST bias.

Tap Save.

5.5.4 Change Administrator's Password on Mobile Web

You can change administrator's password.

Steps

Tap → User Management → admin to enter the sengs page.

Enter the old password and create a new password.

Conrm the new password.

Tap Save.

Note

The password strength of the device can be automacally checked. We highly recommend you

change the password of your own choosing (using 8 to 16 characters, including at least two kinds

of following characters: upper case leers, lower case leers, numbers, and special characters,

and do not contain following characters in the password: the user name, 123, admin (case

insensive), 4 or more connuously increasing or decreasing digits, or 4 or more consecuvely

repeated characters) in order to increase the security of your product. We recommend you

DS-K1T809 Series Access Control Terminal User Manual

change your password regularly, especially in the high security system, changing the password

monthly or weekly can beer protect your product.

5.5.5 Network Sengs

Set Device Hotspot

Set the device hotspot, and mobile phone can connect to the device to enter the mobile browser.

Steps

Tap → Network Sengs → Device Hotspot .

You can enable device hotspot and view the hotspot name.

Note

By default, the hotspot name is the AP_Device Serial No.

Tap Save.

Plaorm

Access

Plaorm access provides you an opon to manage the devices via plaorm.

Steps

Tap → Device Access → Hik-Connect to enter the sengs page.

Note

Hik-Connect is an applicaon for mobile devices. With the App, you can view live image of the

device, receive alarm nocaon and so on.

Check Enable to enable the funcon.

You can view Network Connecon Status and Account Linkage Status.

Tap Save to enable the

sengs.

Set Wiegand Parameters

You can set the Wiegand transmission direcon.

Steps

Tap

→ Access Conguraon → Wiegand Sengs .

DS-K1T809 Series Access Control Terminal User Manual

Figure 5-3 Wiegand Page

Enable Wiegand to enable the Wiegand funcon.

Set a transmission direcon.

Note

The device can connect an external access controller. And the two devices will transmit the card

No. via Wiegand 26 or 34.

Tap More, and you can set Time Interval and Pulse Width.

Tap Save to save the

sengs.

5.5.6 User Management

You can add, edit, delete, and search users via mobile Web browser.

Steps

Tap → Person Management to enter the sengs page.

DS-K1T809 Series Access Control Terminal User Manual

Figure 5-4 User Management

Add user.

1) Tap+.

2) Set the following parameters.

Employee No.

Enter the employee No. The Employee No. cannot be 0 or exceed 32 characters. It can be a

combinaon of uppercase leers, lowercase leers and numbers.

Name

Enter your name. The name supports numbers, English uppercase and lowercase leers

and Chinese characters. The name is recommended to be within 32 characters.

Long-Term Eecve User

DS-K1T809 Series Access Control Terminal User Manual

Set the user permission as long-term eecve, or set the start date and end date of user

permission.

User Type

Select your user role.

Card

Add card. Tap Card, then tap +. Enter the card No. or swipe the card to read card No., and

then select Card Type.

3) Tap Save.

Oponal: Tap the user that needs to be edited in the user list to edit the informaon.

Oponal: Tap the user that needs to be deleted in the user list, and tap to delete the user.

Oponal: You can search the user by entering the employee ID in the search bar.

5.5.7 Search Event

Tap → Search to enter the page.

Enter the search

condions, including the event type, major type, sub type, employee No., card

No., start me, and end me, and tap Search.

Note

Support searching for names within 32 digits.

5.5.8 Access Control Sengs

Set Authencaon Parameters

Set Authencaon Parameters.

Steps

Tap → Access Control → Authencaon Sengs .

DS-K1T809 Series Access Control Terminal User Manual

Figure 5-5 Set Authencaon Parameters

Tap Save.

Terminal

Select the terminal.

Authencaon Type

Select an authencaon type according to your actual needs from the drop-down list.

Authencaon Interval

You can set the authencaon interval of the same person when authencang. The same

person can only authencate once in the congured interval. A second authencaon will be

failed.

Max. Authencaon Failed Aempts Alarm/Max. Authencaon Failed Aempts

Aer you enable Max. Authencaon Failed Aempts Alarm, you can set Max.

Authencaon Failed Aempts. The device will automacally generate and report alarm

events aer the authencaon failures exceed the congured aempts.

DS-K1T809 Series Access Control Terminal User Manual

Max. Interval When Entering Password

You can set the Max. meout period for password entry, aer which the password input will

be invalid.

Enable Card No. Reversing

If this funcon is enabled, the card reader will reverse the order of the card No. aer reading

them.

Set Door Parameters

Tap → Access Control → Door Parameters .

DS-K1T809 Series Access Control Terminal User Manual

Figure 5-6 Door Parameters Sengs

Tap Save to save the sengs aer the conguraon.

Door Name

You can create a name for the door.

Door Opening Duraon(s)

Set the door open duraon.

Exit Buon Type

DS-K1T809 Series Access Control Terminal User Manual

You can set the exit buon as Remain Open or Remain Closed according to your actual needs.

By default, it is Remain Closed.

Door Opening Timeout Alarm Threshold

An alarm will be triggered if the door has not been closed within the congured me duraon.

Door Magnec Sensor Type

You can set the Door Magnec Sensor Type as Remain Open or Remain Closed according to

your actual needs. By default, it is Remain Closed.

Door Opening

Duraon in Special Scene(s)

The door contact can be enabled with appropriate delay aer person with extended access

needs swiping her/his card.

Duress Code

The door can open by inpung the duress code when there is duress. At the same me, the

client can report the duress event.

Super Password

The specic person can open the door by inpung the super password.

Note

The duress code and the super code should be dierent. And the digit ranges from 4 to 8.

Set Card Security

Tap → Card Sengs to enter the sengs page.

Set the parameters and tap Save.

Enable EM Card

Enable EM card and

authencang by presenng EM card is available.

5.5.9 Upgrade and Maintenance

You can restart device, restore device parameters, and upgrade device.

Restart Device

Tap → Restart .

Tap Restart to restart the device.

Upgrade

Tap → Upgrade .

Tap Upgrade to upgrade the device.

DS-K1T809 Series Access Control Terminal User Manual

Note

Do not power o during the upgrading.

Restore Parameters

Tap → Default .

Restore to Default

Sengs

The device will restore to the default sengs, except for the device network parameters and

the user informaon.

Restore to Factory Sengs

All parameters will be restored to the factory sengs. You should acvate the device before

usage.

5.5.10 View Online Document

Tap → View Online Document . Tap View Online Document, you can scan the QR code with

your mobile phone for details.

DS-K1T809 Series Access Control Terminal User Manual

Appendix A. Legal Informaon

About this Document

●

This Document includes instrucons for using and managing the Product. Pictures, charts,

images and all other

informaon hereinaer are for descripon and explanaon only.

●

The

informaon contained in the Document is subject to change, without noce, due to

rmware updates or other reasons. Please nd the latest version of the Document at the

Hikvision website ( hps://www.hikvision.com ). Unless otherwise agreed, Hangzhou Hikvision

Digital Technology Co., Ltd. or its aliates (hereinaer referred to as "Hikvision") makes no

warranes, express or implied.

●

Please use the Document with the guidance and assistance of professionals trained in

supporng the Product.

About this Product

●

This product can only enjoy the aer-sales service support in the country or region where the

purchase is made.

●

If the product you choose is a video product, please scan the following QR code to obtain the

"Iniaves on the Use of Video Products", and read it carefully.

Acknowledgment of Intellectual Property Rights

●

Hikvision owns the copyrights and/or patents related to the technology embodied in the

Products described in this Document, which may include licenses obtained from third pares.

●

Any part of the Document, including text, pictures, graphics, etc., belongs to Hikvision. No part

of this Document may be excerpted, copied, translated, or modied in whole or in part by any

means without

wrien permission.

●

and other Hikvision's trademarks and logos are the properes of Hikvision in

various

jurisdicons.

●

Other trademarks and logos menoned are the properes of their respecve owners.

LEGAL DISCLAIMER

●

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS DOCUMENT AND THE

PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, ARE PROVIDED "AS

IS" AND "WITH ALL FAULTS AND ERRORS". HIKVISION MAKES NO WARRANTIES, EXPRESS OR

DS-K1T809 Series Access Control Terminal User Manual

IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, OR

FITNESS FOR A PARTICULAR PURPOSE. THE USE OF THE PRODUCT BY YOU IS AT YOUR OWN RISK.

IN NO EVENT WILL HIKVISION BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL,

INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF

BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA, CORRUPTION OF SYSTEMS, OR

LOSS OF DOCUMENTATION, WHETHER BASED ON BREACH OF CONTRACT, TORT (INCLUDING

NEGLIGENCE), PRODUCT LIABILITY, OR OTHERWISE, IN CONNECTION WITH THE USE OF THE

PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR

LOSS.

●

YOU ACKNOWLEDGE THAT THE NATURE OF THE INTERNET PROVIDES FOR INHERENT SECURITY

RISKS, AND HIKVISION SHALL NOT TAKE ANY RESPONSIBILITIES FOR ABNORMAL OPERATION,

PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER-ATTACK, HACKER ATTACK,

VIRUS INFECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE

TIMELY TECHNICAL SUPPORT IF REQUIRED.

●

YOU AGREE TO USE THIS PRODUCT IN COMPLIANCE WITH ALL APPLICABLE LAWS, AND YOU ARE

SOLELY RESPONSIBLE FOR ENSURING THAT YOUR USE CONFORMS TO THE APPLICABLE LAW.

ESPECIALLY, YOU ARE RESPONSIBLE, FOR USING THIS PRODUCT IN A MANNER THAT DOES NOT

INFRINGE ON THE RIGHTS OF THIRD PARTIES, INCLUDING WITHOUT LIMITATION, RIGHTS OF

PUBLICITY, INTELLECTUAL PROPERTY RIGHTS, OR DATA PROTECTION AND OTHER PRIVACY

RIGHTS. YOU SHALL NOT USE THIS PRODUCT FOR ANY PROHIBITED END-USES, INCLUDING THE

DEVELOPMENT OR PRODUCTION OF WEAPONS OF MASS DESTRUCTION, THE DEVELOPMENT OR

PRODUCTION OF CHEMICAL OR BIOLOGICAL WEAPONS, ANY ACTIVITIES IN THE CONTEXT

RELATED TO ANY NUCLEAR EXPLOSIVE OR UNSAFE NUCLEAR FUEL-CYCLE, OR IN SUPPORT OF

HUMAN RIGHTS ABUSES.

●

IN THE EVENT OF ANY CONFLICTS BETWEEN THIS DOCUMENT AND THE APPLICABLE LAW, THE

LATTER PREVAILS.

Data

Protecon

●

To protect data, the development of Hikvision Products incorporates privacy by design

principles. For example, for Products with facial

recognion features, biometrics data is stored in

your Products with encrypon method; for ngerprint Products, only ngerprint template will be

saved, which is impossible to reconstruct a

ngerprint image.

●

As a data controller/processor, you may process personal data, including collecon, storage, use,

processing, disclosure,

deleon, etc. You are advised to pay aenon to and comply with

applicable laws and regulaons related to the protecon of personal data, including without

limitaon, conducng security controls to safeguard personal data, such as, implemenng

reasonable administrave and physical security controls, conduct periodic reviews and the

assessments of the

eecveness of your security controls.

DS-K1T809 Series Access Control Terminal User Manual

Appendix B. Symbol Convenons

The symbols that may be found in this document are dened as follows.

Symbol Descripon

Danger

Indicates a hazardous situaon which, if not avoided, will or could

result in death or serious injury.

Cauon

Indicates a potenally hazardous situaon which, if not avoided, could

result in equipment damage, data loss, performance degradaon, or

unexpected results.

Note

Provides addional informaon to emphasize or supplement

important points of the main text.

DS-K1T809 Series Access Control Terminal User Manual

Appendix C. Dimension

Figure C-1 Dimension

Note

The pictures here are for reference only.

DS-K1T809 Series Access Control Terminal User Manual

UD39498B

Hikvision DS-K1T809MWX Value Card Terminal

Product's Documents

Hikvision DS-K1T809MWX User Manual

Specifications

Hikvision DS-K1T809MWX Questions and Answers