DEEPCLEAN
PREMIER®
USER GUIDE
36Z9 Series
2
www.BISSELL.com
IMPORTANT SAFETY INSTRUCTIONS
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK
OR INJURY:
»Connect to a properly grounded outlet only. See grounding
instructions. Do not modify the 3-prong grounded plug.
»Do not leave appliance when it is plugged in. Unplug from
outlet when not in use and before servicing.
»Use indoors only.
»Do not allow to be used as a toy. Close attention is
necessary when used by or near children.
»Do not use for any purpose other than described in this
user guide. Use only manufacturer’s recommended
attachments.
»Do not use with damaged cord or plug. If appliance is not
working as it should, has been dropped, damaged, left
outdoors, or dropped into water, have it repaired at an
authorized service center.
»Always install float before any wet pick-up operation.
»Do not pull or carry by cord, use cord as a handle, close a
door on cord, or pull cord around sharp edges or corners.
Do not run appliance over cord. Keep cord away from
heated surfaces.
»Do not unplug by pulling on cord. To unplug, grasp the
plug, not the cord.
»Do not handle plug or appliance with wet hands.
»Do not put any object into openings. Do not use with any
opening blocked; keep openings free of dust, lint, hair, and
anything that may reduce air flow.
»Keep hair, loose clothing, fingers, and all parts of body
away from openings and moving parts.
»Turn OFF all controls before plugging or unplugging
appliance.
»Do not use to pick up toxic material (chlorine bleach,
ammonia, drain cleaner, etc.).
»Use extra care when cleaning on stairs.
»Do not use to pick up flammable or combustible materials
(lighter fluid, gasoline, kerosine, etc.). or use in areas
where they may be present.
»Do not use appliance in an enclosed space filled with
vapors given off by oil-based paint, paint thinner, some
moth-proofing substances, flammable dust, or other
explosive or toxic vapors.
»Do not pick up anything that is burning or smoking, such
as cigarettes, matches or hot ashes.
»Use only BISSELL® cleaning products intended for use with
this appliance to prevent internal component damage. See
the Cleaning Fluid section of this guide.
»Unplug before connecting TurboBrush® Tool.
»Do not immerse. Use only on surfaces moistened by the
cleaning process.
»Keep appliance on a level surface.
»Do not carry the appliance while in use.
»Keep hair, loose clothing, fingers, and all parts of body
away from openings and moving parts of the appliance
and its accessories.
»Plastic film can be dangerous. To avoid danger of
suffocation, keep away from children.
»Do not pick up hard or sharp objects such as glass, nails,
screws, coins, etc.
»Do not use without filters in place.
»Do not pick up hard or sharp objects such as glass, nails,
screws, coins, etc.
»Liquid must not be directed towards equipment containing
electrical components.
»Use only the type and amount of liquids specified under
the operations section of this guide.
»If your appliance has a motorized Brush Roll, do not leave
machine running in the same spot without the handle fully
upright.
READ ALL INSTRUCTIONS BEFORE USING YOUR DEEP CLEANER.
When using an electrical appliance, basic precautions should be observed, including the following:
SAVE THESE INSTRUCTIONS FOR FUTURE USE
This model is for household use only. Commercial use of this machine voids the manufacturer’s warranty.
WARNING
Improper connection of the equipment-grounding conductor can
result in a risk of electrical shock. Check with a qualified electrician or
service person if you aren’t sure if the outlet is properly grounded.
DO NOT MODIFY THE PLUG. If it will not fit the outlet, have a proper
outlet installed by a qualified electrician. This appliance is designed
for use on a nominal 120-volt circuit, and has a grounding attachment
plug that looks like the plug in the illustration. Make certain that the
appliance is connected to an outlet having the same configuration as
the plug. No plug adapter should be used with this appliance.
GROUNDING INSTRUCTIONS
This appliance must be connected to a grounded wiring system. If it
should malfunction or break down, grounding provides a safe path
of least resistance for electrical current, reducing the risk of electrical
shock. The cord for this
appliance has an equipment-grounding
conductor and a grounding plug. It must
only be plugged into an outlet that is
properly installed and grounded in
accordance with all local codes and ordinances.
Grounded
Outlets
Grounding Pin
3
www.BISSELL.com
Th for buying a BISSELL
®
dp cleer
We’re glad you purchased a BISSELL
deep cleaner. Everything we know
about floorcare went into the design
and construction of this complete,
high-tech home cleaning system.
Your BISSELL deep cleaner is well
made, and we back it with a limited
three-year warranty. We also stand
behind it with a knowledgeable,
dedicated Consumer Care
department, so, should you ever
have a problem, you’ll receive fast,
considerate assistance.
My great-grandfather invented
the floor sweeper in 1876. Today,
BISSELL is a global leader in the
design, manufacture, and service
of high quality homecare products
like your BISSELL deep cleaner.
Thanks again, from all of us
at BISSELL.
Mark J. Bissell
Chairman & CEO
Safety Instructions...........2
Product View ................4
Assembly ...................4
Operations ..................5
Maintenance & Care ........12
Troubleshooting ............13
Warranty ...................14
Product Registration........16
» Deep cleaning stairs and high-trac areas on a regular
basis helps prolong carpet life.
» Check upholstery stung before cleaning. Colored
stung may bleed through the fabric when it
becomes wet.
» Before turning OFF the machine, suction up clean
water to thoroughly rinse out the interior of the Flex
Hose. Then, lift the cleaning tool and point it upwards
to drain any remaining water into the dirty water/
collection tank.
Tips
4
www.BISSELL.com
Product View
1 Spray Trigger
2 Extra Long Power Cord
3 Upper Handle
4 Flex Hose
5 Power Switch
6 Carry Handle
7 Tank Carry Handle
8 Large Capacity 2-in-1 Water Tank
9 Surround Suction®
10 Easy To Remove Nozzle
11 EdgeSweep® Brushes
12 Lower Base
13 Upper Hose Wrap
14 Lower Hose Wrap
15 Handle Recline Pedal
1
2
4
3
5
6
7
8
9
10
11
12
13
14
15
Assembly
Your deep cleaner comes in three (four on
select models) easy-to-assemble components:
Upper Handle with Screws
Lower Base
Upper Hose Wrap
Upper Tool Holder (select models)
The only thing you will need to assemble
your cleaner is a Phillips-head screwdriver.
1. Slide Upper Handle onto lower handle.
2. Screw 2 screws into the marked holes
(screws will be taped to handle).
3. Attach the Upper Tool Holder (select models)
to the Upper Handle by snapping the bottom
half in first, then snapping in the top half.
4. Place Upper Hose Wrap onto back of
Upper Handle, and secure with screw.
5. Snap tools onto the Upper Tool Holder
(select models).
6. Wrap power cord and Flex Hose. Snap hose
wand into hose clip on upper hose wrap.
NOTE: Take care to wrap the hose in the
right direction in order to make use of the
hose clip. Make sure the hose is wrapped
beginning from the back of the machine
and wrapping toward the front.
Deep cleaner assembly is now complete.
6.
5.
4a.
3.
4b.
1. 2.
5
www.BISSELL.com
Operations
Keep plenty of BISSELL® cleaning formulas on hand so
you can clean whenever it fits your schedule.
NOTE: Always use genuine BISSELL cleaning formulas
upholstery washers in your machine.
Clean + Refresh
Powerful cleaning and odor
elimination with Febreze
freshness
PET Stain & Odor
Removes tough pet stains
Includes StainProtect
™
to
protect against future
stains
PRO MAX
Clean + Protect
Our most powerful formula
for tough, ground-in dirt
& stains
Includes StainProtect to
protect against future
stains
PET PRO OXY Urine
Eliminator
Our best formula for pet
urine stains & odors
Includes StainProtect to
protect against future
stains
Certain trademarks used under license from The Procter & Gamble Company or its affiliates.
OXY Boost
Removes old,
set-in stains
PRO MAX
Boost
Add to formula
for 2X deep
cleaning power
PET OXY
Boost
Removes pet
stains and odors
PET Stain
Pretreat
Removes tough
pet stains &
odors with
Enzyme Action
PET PRO
OXY Stain
Destroyer
Removes tough
pet stains &
odors with OXY
PET Pretreat
+ Sanitize
Penetrates to
sanitize and
loosen tough
stains
Pretreat
Pretreat spots and stains to improve carpet
cleaning performance.
Boost
Add Boost carpet cleaning formula enhancers to
any formula to increase its effectiveness.
Cleaning Formulas
WARNING
To reduce the risk of fi re and electric shock due to internal component damage, use only BISSELL cleaning formula intended for use with
this machine.
To reduce the risk of fi re and electric shock, when cleaning a hard fl oor, the BISSELL bare fl oor tool must be used and it must only be used with
BISSELL 2X Hard Floor Solutions cleaning fl uid intended for use with this appliance. Visit BISSELL.com to purchase.
6
www.BISSELL.com
Operations
Before You Clean
1. Move furniture to another area if cleaning
an entire room (optional).
2. Pick up all loose dirt, debris, and pet hair
before deep cleaning. It is recommended that
you vacuum the area prior to deep cleaning.
3. Plan your cleaning route to leave an exit
path. It is best to begin cleaning in the corner
farthest from your exit.
4. Pretreating (optional)
Pretreating is recommended to improve cleaning
effectiveness for heavily soiled carpet in high-
traffic areas such as entryways and hallways.
a. Using a BISSELL Stain pretreater,
generously spray evenly over soiled area.
Do not overwet.
b. Wait 3-5 minutes before deep cleaning.
c. Clean as normal using your BISSELL®
deep cleaner.
Machine Prep
1. Fill the 2-in-1 Water Tank. Remove the tank
from the base of the machine by lifting up the
tank Carry Handle. Carry like a bucket to the
sink.
2. Unlatch the top of the tank from the bottom
by lifting up on the tank latches on either
side of the tank.
3. Using the measuring cup provided,
pour 2.5 oz. of BISSELL formula into the
heavy-duty bladder. Fill the rest of the bladder
with hot tap water. DO NOT BOIL
OR MICROWAVE WATER.
NOTE: Always use genuine BISSELL
formulas to maximize cleaning and for the
safety of your machine.
4. Place the top of the tank back on the
bottom and secure the latches on both sides.
NOTE: Remember to secure the tank latches
on either side of the tank and test to make sure
they are secure before picking up the tank.
WARNING
To reduce the risk of fire and electric shock
due to internal component damage, use
only BISSELL cleaning formulas intended for
use with the deep cleaner.
ATTENTION
Some Berber carpets have a tendency to fuzz
with wear. Repeated strokes in the same area
with an ordinary vacuum or deep cleaner
may aggravate this condition. Please see Stain
Removal instructions on page 11.
1
2
3
4
5
6
7
8
9
1. 2.
3. 4.
7
www.BISSELL.com
Carpet Cleaning
1. Plug into a proper outlet and push the Power
Switch located on the front of the handle.
2. Recline the handle by pressing on the lever
at the back of the machine behind the 2-in-1
Water Tank.
3. Cleaning Strokes. While pressing the trigger,
make one slow forward wet pass and another
one back. Caution: Do not overwet. Take care
not to run over loose objects or edges of area
rugs. Stalling brush may result in premature
belt failure.
NOTE: Your machine is equipped with a circuit
breaker that will automatically shut off the
brush if a large or loose object is caught in the
Brush Roll. If that happens, be sure to unplug
your machine, remove the foreign object, and
then plug the machine back in to reset the
circuit breaker.
4. Release the trigger and make one slow
forward and backward pass over the same area
to remove any residual dirty water and aid in
drying. Repeat cleaning passes until solution
being pulled up appears clean. Continue
passes without pressing the trigger until you
can’t see any more water being pulled up.
CleanShot® (select models)
CleanShot is an optional feature that can be
used to fight tough stains. It can be used as
either a tough stain pretreater or can be used
during the deep cleaning process itself. To use
CleanShot either way, follow the instructions
below.
1. Press the CleanShot button on the front of
the machine’s handle and aim the focused
stream onto the stain for up to 5 seconds.
2. Allow the formula to soak in for 15 seconds.
3. Run the machine over the stain to extract
until no formula or water can be seen coming
up from the carpet.
4. Repeat as needed until the stain is gone.
1.
1. 2.
Operations
8
www.BISSELL.com
Cleaning with Attachments
Your deep cleaner comes equipped with
a hose and at least one attachment for
cleaning stairs, upholstery and more.
1. Important! If using to clean upholstery,
check upholstery tags.
1. Check manufacturer’s tag before cleaning.
“W” or “WS” on the tag means you can use your
deep cleaner. If the tag is coded with an “X” or
an “S” (with a diagonal stripe through it), or says
“Dry Clean Only”, do not proceed with any deep
cleaning machine. Do not use on velvet or silk.
If manufacturer’s tag is missing or not coded,
check with your furniture dealer.
a. Check for colorfastness in an
inconspicuous place.
b. If possible, check upholstery stuffing.
Colored stuffing may bleed through
fabric when wet.
c. Plan activities to allow upholstery
time to dry.
d. Pick up any loose dirt, debris and
pet hair before deep cleaning.
2. Follow the instructions on page 6 for
filling the 2-in-1 Water Tank.
3. The DeepClean Premier® is designed with
an automatic diverter. Simply lock the machine
upright in order to clean with the hose.
4. Attach the cleaning tool to the end of the hose.
5. Plug in and turn on the Power Switch.
6. Clean by pressing the trigger to spray
solution onto the area to be cleaned. Slowly
move the tool back and forth
over the soiled surface. Release the
trigger to suction soiled water. Continue to clean
in the area, working in small sections, until no
more dirt can be removed. Rinse (optional) and
suction as needed. Caution: Do not overwet.
7. Remove and rinse tools in clean, running
water. Dry and replace on the end of the hose.
8. It is recommended that you suction clean
water from a bowl to rinse out the hose.
9. Before replacing lift end of hose and stretch
out to ensure all water is cleared from hose.
10. Wrap Flex Hose around the hose wrap.
11. Empty 2-in-1 Water Tank and rinse out,
following the instructions on page 9.
4.
9.
WARNING
To reduce the risk of injury, be extra careful when cleaning
stairs. Make sure machine is secure and level.
Operations
Manufacturer’s tag
Adsdfdd ghg bvh
cvbbj jkn hnbj jkvh
gcghhjj jhffhl kllgh
9
www.BISSELL.com
Cleaning with the Stain Trapper Tool (select models)
Your deep cleaner may have come with a Stain
Trapper Tool. This tool is great for keeping messes
out of the machine’s hose system.
1. Attach the Stain Trapper Tool to the end of the
hose.
2. Gently scrape up any semi-solids with a spoon
or spatula. Do not use a knife or other utensil with
sharp edges because it could damage the carpet or
upholstery.
3. Follow instructions 3-6 on page 8 under “Cleaning
with attachments”.
NOTE: Do not fill the Stain Trapper tank above the
FULL line.
4. To empty the tool, rotate the small tank on the
bottom of the tool to unlock it.
NOTE: Be careful to keep the top of the tool facing
upward or soiled water will spill out of the tank.
5. Dump dirty water into a sink or toilet and
rinse the tank out with clean water. Replace the
tank by lining up the unlock symbol with the
small arrow on the tank and turning it to the lock
symbol.
6. Clean the front of the tool by removing the
plate over the suction path. Pull down on the
bottom of the plate to remove. Run the tool and
the plate under clean water to rinse taking care
to remove all debris. Replace the front plate by
sliding it back into place.
Clean-Up
1. Remove the tank from the base of the machine
by lifting up on the tank Carry Handle. Carry like
a bucket to a utility sink or outside where you
will dispose of the dirty water.
2. Unlatch the top of the tank from the bottom
by lifting up on the tank latches on either side of
the tank.
3. Remove the top of the tank by lifting up on
the handle.
4. Lift the bottom portion of the tank; pour out
dirty water in the sink through the rectangular
shaped opening in the corner of the tank.
NOTE: You may notice hair & debris deposits
on the carpet or in the tank that were loosened
by the cleaning action. This debris should be
picked up and thrown away. Check the red lint
filter near the duct on the back of the machine
base for debris and remove before continuing.
1.
3.
2.
4.
Filter
6.
4.
Operations
10
www.BISSELL.com
5.
5. Empty the Pet Hair Basket (select models)
by sliding it toward the front of the tank and
lifting up. Replace the Pet Hair Basket before
storing/continuing to clean.
6. Fill the heavy-duty bladder with clean hot
tap water, following instructions on page 6.
NOTE: Remember to secure the tank latches and
test to make sure it is secure before
picking up the tank.
7. Water rinse (recommended). Rinsing
is an optional step that can be done during the cleaning
process or after the carpeted area has been completed. Empty
the heavy-duty bladder if necessary, and refill with hot tap
water only. Replace the tank on the machine. Take care to do a
forward (wet) stroke by depressing the
trigger, and a backward (wet) stroke, followed by a forward and
backward (dry) stroke, releasing the trigger. Continue this until
the water you see coming up the nozzle is clear. (See page 11
for maintenance tips.)
Stain Removal
Do Not Delay! Attending to an accident soon after it occurs
ensures the most optimal clean. Leaving it for an extended
period of time may cause it to set and become permanent.
1. Blot up liquids with an absorbent cloth or paper towels. White
materials are recommended because certain dyes may bleed
and make the stain worse.
2. Gently scrape up any semi-solids with a spoon or spatula.
Do not use a knife or other utensil with sharp edges because it
could damage the carpet or upholstery.
3. If the area has already dried, separate and remove from the
carpet whatever semi-solids and residue that can be accessed
before deep cleaning.
4. Be sure to test any spot removal formulas in an
inconspicuous area first. This is important as some dyes
and materials could be damaged or discolored by cleaning
solvents. If such a change should occur, try a different solution
or call a professional.
5. If cleaning on Berber carpeting, gently run your machine over
a hidden area. If no fuzzing occurs, continue cleaning in soiled
area.
6. Using a BISSELL® pretreater, spray evenly over soiled area.
Do not overwet. Wait 3-5 minutes. Gently work the solution by
blotting area with a clean, damp, color safe cloth.
7. Clean large areas with the DeepClean Premier® machine or
use the hose to clean spots, stains and hard-to-reach areas.
Machine Storage
Once your cleaning is complete, make sure the 2-in-1 Water
Tank is emptied, rinsed out, and dried before the next use.
NOTE: Store cleaner in a protected, dry area. To reduce the risk
of a leaking condition, do not store appliance where freezing
may occur. Damage to internal components may result.
Operations
11
www.BISSELL.com
Machine Care
For best results, a few simple steps can assure
your machine is well maintained after your
cleaning is complete.
1. Flush your machine of any remaining solution.
a. Fill the 2-in-1 Water Tank with clean hot
tap water.
b. Recline the handle and press the Spray
Trigger for 15 seconds while making forward
and backward passes on carpet. Release
the trigger to suction. Repeat for another
15 seconds. Continue without pressing the
trigger until there is no more water being
suctioned.
2. Push the Power Switch to turn the machine
OFF. Unplug the machine and wrap the power
cord. Empty the 2-in-1 Water Tank.
3. Rinse out tank with hot tap water, taking care
to clean underneath the heavy-duty bladder and
all around it.
4. The top half of the tank can be rinsed clean
through the nozzle area. Clear the red filter of
any debris that may have accumulated.
5. Keeping the tank off the base of the machine,
simply remove the floor nozzle by turning the
locking keys (see image for location) to the
unlock position and lift up. Rinse the floor nozzle
at the faucet.
6. Any loose hair or debris can be pulled from
the Brush Rolls and thrown away. For the most
thorough clean before storage, follow directions
below for removal and replacement of the Brush
Rolls and belts.
7. Replace nozzle by lining up the locking keys
with their slots and placing the nozzle and end
caps back onto the foot of the machine. Secure
into place by turning the locking keys to the lock
position.
8. To clean attachments that may have been
used, remove from hose and rinse under clean,
running water. Dry and replace attachment in
the hose wrap. Clean the hose by suctioning
clean water from the tap. Before replacing, lift
end of hose and stretch out to ensure all water is
cleared from hose. Refer to page 8.
9. To clean the suction diverter, remove the two
screws on the back of the diverter housing. Take
the diverter housing to a sink and rinse it with
water. Take care to remove any debris that may
build up and cause a clog. Replace the diverter
housing and the two screws.
10. After carpet is dry, vacuum again to remove
hair and fuzz.
4.
Filter
Diverter
5. 6.
9.
» Let all parts
dry completely
before storing
Tip
WARNING
To reduce the risk of electric shock, turn Power Switch
OFF and disconnect plug from electrical outlet before
performing maintenance or troubleshooting checks.
Maintenance & Care
12
www.BISSELL.com
Drive Belt Removal & Replacement
Occasional replacement of one or both belts
may become necessary. If that is needed, please
follow the instructions below.
1. Turn OFF the machine, and unplug it from
the outlet.
2. Remove the 2-in-1 Water Tank. Set aside.
3. Remove the nozzle and endcaps following the
instructions below.
4. Turn the machine on its side.
IMPORTANT: cord side up.
5. Remove 1 silver screw from the pivot arm.
6. Remove pivot arm by gently lifting up.
7. Remove the drive belt and replace it by first
attaching it to the small drive wheel, then attach
it to the end of the inside brush.
Fluid Connection Point Filter Maintenance
Periodic cleaning of the fluid connection
point in the spray nozzle may be required.
1. To clean the fluid connection point,
remove the nozzle and turn it over.
2. Clean the filter on the end of the fluid
connection point with a small paperclip
and re-attach the nozzle to the machine.
3.
1. 2.
4.
5. 7.
Maintenance & Care
2.
5.
7.
Brush Removal and Brush Belt Replacement
Brushes can be removed for cleaning or
replacement as needed.
1. Follow drive belt removal instructions above.
2. Remove Brush Rolls by pulling them off of
the metal rods. Be careful not to lose the small
washer at each end of the Brush Rolls.
3. Replace the brush belt if necessary.
4. Place cleaned or new Brush Rolls back onto
the rods. Make sure one washer is on each end
of the rollers prior to sliding onto the rod. Be
sure to let the rod slide through the bushing to
insure proper fit.
5. Reattach the brush belt on the bottom to the
cogs of the small roller brushes.
6. Replace the drive belt by following step 7
above.
7. Place pivot arm in place and screw in place
using the silver screw.
8. Replace nozzle by lining up the locking keys
with their slots and placing the nozzle back onto
the foot of the machine. Secure into place by
turning the locking keys to the lock position.
If you have any questions or are having trouble
installing or replacing your belt(s) or brushes,
please call BISSELL® Consumer Care.
13
www.BISSELL.com
WARNING
To reduce the risk of electric shock, turn Power Switch OFF and disconnect plug from electrical outlet before performing maintenance
or troubleshooting checks.
Problem Possible causes Remedies
Reduced
spray or
no spray
2-in-1 Water Tank may be empty. Fill heavy-duty bladder with hot
tap water.
Tank may not be seated
completely.
Turn power OFF. Remove and
reseat tank.
Pump may have lost prime. Turn power OFF and then back ON.
Wait one minute, then press trigger.
DirtLifter®
PowerBrush
does not turn
The belt is off or broken. Turn power OFF and unplug machine
from outlet. Follow instructions on
page 12.
Circuit breaker on machine may
have tripped.
Turn the machine OFF and unplug
from outlet. Check to see if foreign
object is caught in Brush Roll.
Remove object. Plug machine in to
reset circuit breaker.
Cleaner
not picking
up solution
2-in-1 Tank may not be seated
properly.
Pick up and reseat the tank.
Tank may not be assembled
properly.
Make sure the tank latches on both
sides of the tank are latched properly. To
make sure they are both latched prop-
erly, pick the tank up by its handle.
2-in-1 Water Tank is empty. Check fluid levels in heavy-duty
bladder.
2-in-1 Water Tank has picked up
maximum dirty water and red
float door has closed.
Empty tank. Refill heavy-duty bladder
with clean hot tap water and replace.
Red float "door" in the tank may
have closed as a result of bump-
ing object or moving machine
back and forth too quickly.
Turn the machine OFF , allowing red
float door to release an into the open
position. Turn machine back ON to
continue cleaning. Be sure your
forward and backward strokes are
done at a slower pace.
Red lint screen near air duct
is dirty.
Follow cleaning instructions on page 9.
Troubleshooting
14
www.BISSELL.com
This warranty gives you specific legal rights,
and you may also have other rights which may
vary from state to state. If you need additional
instruction regarding this warranty or have
questions regarding what it may cover, please
contact BISSELL Consumer Care by E-mail or
telephone as described below.
It may be necessary to obtain some of your
personal information, such as a mailing
address, to fulfill terms of this warranty. Any
personal data will be handled pursuant to
BISSELL’s Privacy Policy, which can be found
online at www.BISSELL.com/privacy-policy.
Limited Three-Year Warranty
Subject to the *Exceptions and Exclusions
from the Terms of the Limited Warranty, upon
receipt of the product BISSELL will repair or
replace (with new, refurbished, lightly used, or
remanufactured components or products), at
BISSELL’s option, free of charge from the date
of purchase by the original purchaser, for three
years, any defective or malfunctioning part.
See information below on "If your BISSELL
product should require service”.
This warranty applies to product used for
personal, and not commercial or rental,
service. This warranty does not apply to
fans or routine maintenance components
such as filters, belts or brushes. Damage or
malfunction caused by negligence, abuse,
neglect, unauthorized repair, or any other use
not in accordance with the user guide is not
covered. This warranty will only be valid if the
product is used in the same country in which
it was sold.
BISSELL is not liable for incidental or
consequential damages of any nature
associated with the use of this product.
BISSELL’s liability will not exceed the purchase
price of the product.
Some states do not allow the exclusion or
limitation of incidental or consequential
damages, so the above limitation or
exclusion may not apply to you.
*Exceptions and Exclusions from the
Terms of the Limited Warranty
This warranty is exclusive and in lieu of
any other warranties, either oral or written.
Any implied warranties, which may arise
by operation of law, including the implied
warranties of merchantability and fitness for
a particular purpose, are limited to the three-
year duration from the date of purchase as
described above.
Some states do not allow limitations on how
long an implied warranty lasts, so the above
limitation may not apply to you.
Warranty
NOTE: Please keep your original sales receipt. It provides proof of date of purchase in the
event of a warranty claim.
Service
Website:
www.BISSELL.com/service-centers
E-mail:
www.BISSELL.com/email-us
Call:
BISSELL Consumer Care
1-800-237-7691
Please do not return this product
to the store.
Other maintenance or service not included
in the manual should be performed by an
authorized service representative.
If your BISSELL® product should
require service:
Contact BISSELL Consumer Care to locate
a BISSELL Authorized Service Center in
your area. If you need information about
repairs or replacement parts, or if you have
questions about your warranty, contact
BISSELL Consumer Care.
16
We’re Waggin’ Our Tails!
BISSELL® proudly supports BISSELL Pet Foundation®
and its mission to help save homeless pets. When you
buy a BISSELL product, you help save pets, too. We’re
proud to design products that help make pet messes,
odors and pet homelessness disappear.
Visit BISSELLsavespets.com to learn more.
Registering is quick, easy and offers you benefits over the lifetime of your product.
You’ll receive:
BISSELL® Rewards Points
Automatically earn points for discounts and
free shipping on future purchases.
Faster Service
Supplying your information now saves you
time should you need to contact us with
questions regarding your product.
Product Support Reminders and Alerts
We’ll contact you with any important
product maintenance reminders and alerts.
Special Promotions
Optional: Register your email to receive
notice of offers, contests, cleaning tips, and
more!
Visit BISSELL.com/registration!
Love yr BISSELL® product?
Don’t keep it a secret.
Let us, and millions of others, know what you think!
Leave your star-rating on BISSELL.com.
Parts & Supplies
Register your product today!
For Parts and Supplies, go to www.BISSELL.com and enter your model number in
the search field.
©2020 BISSELL Inc. All rights reserved.
Printed in China. Part Number 1623395 03/20 RevA
