UNIMAC NALGASUMCA34E LXG3000 MkII Gas Framing Nail Gun, User Manual

User Manual

[Revision 10.0]

READ THIS MANUAL CAREFULLY BEFORE USE – FAILURE TO DO SO MAY RESULT IN INJURY, PROPERTY DAMAGE

AND MAY VOID WARRANTY. • KEEP THIS MANUAL FOR FUTURE REFERENCE. • Products covered by this manual may

vary in appearance, assembly, inclusions, specifications, description, and packaging.

Framing Nailer - LXG3000 MkII

E&OE © Unimac 2

Safety

Safety messages are designed to alert you to possible dangers or hazards that could cause death, injury or

equipment or property damage if not understood or followed. Safety messages have the following symbols:

You WILL be KILLED or

SERIOUSLY INJURED if you do

not follow instructions.

You CAN be KILLED or

SERIOUSLY INJURED if you do

not follow instructions.

You CAN be INJURED if you do

not follow instructions or equipment

damage may occur.

It is vital that you read and understand this

user manual before using the product,

including safety warnings, and any assembly

and operating instructions. Keep the manual

for future reference.

Safety precautions and recommendations

detailed here must be fully understood and

followed to reduce the risk of injury, fire,

explosion, electrical hazard, and/or property

damage.

Safety information presented here is generic

in nature – some advice may not be

applicable to every product. The term

"equipment" refers to the product, be it

electrical mains powered, battery powered or

combustion engine powered.

• Before Use - If you are not familiar with the

safe operation/handling of the equipment or

are in any way unsure of any aspect of

suitability or correct use for your

application, you should complete training

conducted by a person or organization

qualified in safe use and operation of this

equipment, including fuel/electrical handling

and safety.

• Do NOT operate the equipment in

flammable or explosive environments, such

as in the presence of flammable liquids,

gases or dust. The equipment may create

sparks or heat that may ignite flammable

substances.

• Keep clear of moving parts.

• Equipment may be a potential source of

electric shock or injury if misused.

• Do NOT operate the equipment if it is

damaged, malfunctioning or is in an

excessively worn state.

• Do NOT allow others to use the equipment

unless they have read this manual and are

adequately trained.

• Keep packaging away from children - risk

of suffocation! Operators must use the

equipment correctly. When using the

equipment, consider conditions and pay

due care to persons and property.

General Work Area Safety

• Work areas should be clean and well it.

• Do not operate the equipment if

bystanders, animals etc are within

operating range of the equipment or the

general work area.

• If devices are provided for connecting dust

extraction / collection facilities, ensure

these are connected and used properly.

Dust collection can reduce dust-related

hazards.

General Personal Safety

• W

ear appropriate protective equipment

when operating, servicing, or when in the

operating area of the equipment to help

protect from eye and ear injury, poisoning,

burns, cutting and crush injuries. Protective

equipment such as safety goggles,

respirators, non-slip safety footwear, hard

hat, hearing protection etc should be used

for appropriate equipment / conditions.

Other people nearby should also wear

appropriate personal protective equipment.

Do not wear loose clothing or jewellery,

which can be caught in moving parts. Keep

hair and clothing away from the equipment.

• Stay alert and use common sense when

operating the equipment. Do not over-

reach. Always maintain secure footing and

balance.

• Do not use the equipment if tired or under

the influence of drugs, alcohol or

medication.

• This equipment is not intended for use by

persons with reduced physical, sensory or

mental capabilities.

General Fuel Safety

• P

etrol/fuel/gasoline is extremely flammable

– keep clear of naked flames or other

ignition sources.

• Do not spill fuel. If you spill fuel, wipe it off

the equipment immediately – if fuel gets on

your clothing, change clothing.

• Do NOT smoke near fuel or when

refuelling.

• Always shut off the engine before

refuelling.

• Do NOT refuel a hot engine.

• Open the fuel cap carefully to allow any

pressure build-up in the tank to release

slowly.

• Always refuel in well ventilated areas.

• Always check for fuel leakage. If fuel

leakage is found, do not start or run the

engine until all leaks are fixed.

General Carbon-Monoxide Safety

• U

sing a combustion engine indoors CAN

KILL IN MINUTES. Engine exhaust

contains carbon-monoxide – a poison you

cannot smell or see.

• Use combustion engines OUTSIDE only,

and far away from windows, doors and

vents.

General Equipment Use and Care

• T

he equipment is designed for domestic

use only.

• Handle the equipment safely and carefully.

• Before use, inspect the equipment for

misalignment or binding of moving parts,

loose components, damage or any other

condition that may affect its operation. If

damaged, have the equipment repaired by

an authorised service centre or technician

before use.

• Prevent unintentional starting of the

equipment - ensure equipment and power

switches are in the OFF position before

connecting or moving equipment. Do not

carry equipment with hands or fingers

touching any controls. Remove any tools or

other items that are not a part of the

equipment from it before starting or

switching on.

• Do not force the equipment. Use the

correct equipment for your application.

Equipment will perform better and be safer

when used within its design and usage

parameters.

• Use the equipment and accessories etc. in

accordance with these instructions,

considering working conditions and the

work to be performed. Using the equipment

for operations different from those intended

could result in hazardous situations.

• Always keep equipment components

(engines, hoses, handles, controls, frames,

housings, guards etc) and accessories

(cutting tools, nozzles, bits etc) properly

maintained. Keep the equipment clean and,

where applicable, properly lubricated.

• Store the equipment out of reach of

children or untrained persons. To avoid

burns or fire hazards, let the equipment

cool completely before transporting or

storing. Never place or store the equipment

near flammable materials, combustible

gases or liquids etc.

• The equipment is not weather-proof, and

should not be stored in direct sunlight, at

high ambient temperatures or locations that

are damp or humid.

• Do not clean equipment with solvents,

flammable liquids or harsh abrasives.

• For specific equipment safety use and care,

see Equipment Safety.

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC `

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC

Framing Nailer - LXG3000 MkII

E&OE © Unimac 3

General Electrical Safety

• I

nspect electrical equipment, extension

cords, power bars, and electrical fittings for

damage or wear before each use. Repair or

replace damaged equipment immediately.

• Ensure all power sources conform to

equipment voltage requirements and are

disconnected before connecting or

disconnecting equipment.

• When wiring electrically powered

equipment, follow all electrical and safety

codes.

• Always use a Residual Current Device

(RCD) (GFCI) / Earth Leakage Circuit

Breaker / Safety Switch when operating this

item (electrical items only).

• High voltage / high current power lines may

be present. Use extreme caution to avoid

contact or interference with power lines.

Electrical shock can be fatal.

General Electrical Safety

• E

lectrically grounded equipment must have

an approved cord and plug and be

connected to a grounded electrical outlet.

• Do NOT bypass the ON/OFF switch and

operate equipment by connecting and

disconnecting the electrical cord.

• Do NOT use equipment that has exposed

wiring, damaged switches, covers or

guards.

• Do NOT use electrical equipment in wet

conditions or in damp locations.

• Do NOT use electrical cords to lift, move or

carry equipment.

• Do NOT coil or knot electrical cords, and

ensure electrical cords are not trip hazards.

General Service Information

• T

he equipment must be serviced or

repaired at authorised service centres by

qualified personnel only.

• Replacement parts must be original

equipment manufacturer (OEM) to ensure

equipment safety is maintained.

• Do NOT attempt any maintenance or repair

work not described in this manual.

• After use, the equipment and components

may still be hot – allow the equipment to

cool and disconnect spark plugs and/or

electrical power sources and/or batteries

from it before adjusting, changing

accessories, or performing repair or

maintenance.

• Do NOT adjust while the equipment is

running.

• Perform service-related activities in suitable

conditions, such as a workshop.

• Replace worn, damaged or missing

warning/safety labels immediately.

FRAMING NAILER SAFETY

• R

ead and understand tool labels and all of the operating instructions, safety precautions and warnings in this manual before operating

or maintaining this nailer. Failure to follow warnings could result in DEATH or SERIOUS INJURY.

• Most accidents that result from the operation and maintenance of nailers are caused by the failure to observe basic safety rules or precautions.

An accident can often be avoided by recognizing a potentially hazardous situation before it occurs, and by observing appropriate safety

procedures.

• Basic safety precautions are outlined in the Safety section of this Manual and in the sections, which contain the operation and maintenance

instructions.

• Hazards that must be avoided to prevent bodily injury or machine damage are identified by DANGERS and WARNINGS on the Nailer and in this

Manual.

• Never use this Nailer for applications other than those specified in this Manual.

• This tool has a FULL SEQUENTIAL ACTUATION ELECTRON CONTROL. First, press the push lever against the workpiece; next, pull the trigger

to drive the nail. Follow the same sequence to continue driving nails.

• This Nailer is powered by internal combustion device. This nailer shall only be used with dispensers for combustible gas which are listed in this

instruction manual.

• OPERATORS AND OTHERS IN WORK AREA MUST WEAR SAFETY GLASSES WITH SIDE SHIELDS. Eye protection must meet the

requirements of ANSI Standard Z87.1 and should have side shields for increased protection. If you are using this nailer at work, the employer

must be responsible for enforcing the use of eye protection equipment by the tool operator and all personnel in the work area.

• NEVER USE IN PRESENCE OF FLAMMABLE LIQUIDS OR GASES. This nailer must not be used in a combustible environment or in presence

of flammable liquids or gases, e.g., lacquer, paint, benzine, thinner or gasoline. This Nailer produces hot exhaust gases that may ignite

flammable materials and produce sparks during operation.

• DO NOT TOUCH AROUND THE EXHAUST OUTLET. This nailer produces hot exhaust gases that may ignite flammable materials. The push

lever and nose will get heated up and become hot after prolonged or rapid use. Do not touch with bare hands.

• EXPLOSION AND FIRE HAZARD. The fuel cell is an aerosol dispenser with flammable contents. Pressured container and the propellant will

remain in the fuel cell. Failure to follow instructions may result in explosion or fire. Keep the nailer, fuel cells and battery away from sunshine and

from temperature exceeding 120°F(50°C). Fuel cell and/or battery may burst, releasing flammable gas. Do not pierce or burn the container, even

after use. Do not incinerate, refill, reclaim or recycle the fuel cell. Do not spray to a naked flame or any incandescent material. Keep away from

ignitable sources - No smoking. Keep out of the reach of children.

• NEVER POINT TOOL AT YOURSELF OR OTHERS IN WORK AREA. Always assume the nailer contains fasteners. Never point the nailer at

yourself or others, whether it contains fasteners or not. If fasteners are mistakenly driven, it can lead to severe injuries. Never engage in

horseplay with the nailer. Respect the nailer as a working implement.

• KEEP FINGERS AWAY FROM TRIGGER WHEN NOT DRIVING FASTENERS TO AVOID ACCIDENTAL FIRING. Never carry the Nailer with

finger on trigger since you could drive a fastener unintentionally and injure yourself or someone else. Always carry the Nailer by the handle only.

• ALWAYS WEAR EAR AND HEAD PROTECTION. Always wear ear protection to protect your ears from loud noise. Always wear head protection

to protect your head from flying objects.

• USE OUTSIDE OR WELL-VENTILATED AREAS. This nailer exhausts carbon monoxide which are a danger to health when inhaled. This nailer

shall not be used in enclosed or poorly ventilated areas. Do not inhale.

• OPERATE WITHIN PROPER TEMPERATURE RANGE. The operating environment for this device is between 32°F (0°C) and 104°F (40°C) so

ensure to use within this temperature range. The device may fail to operate below 32°F (0°C) or above 104°F (40°C).

• STORE NAILER PROPERLY WITH FUEL CELL AND BATTERY REMOVED. When not in use, the Nailer, fuel cell and battery should be store

in tool case and in a dry place. Store indoors at temperature below 120°F (50°C). Keep the Nailer, fuel cell and battery out of direct sunlight and

out of in a vehicle. Keep out of reach of children. Look at the storage area.

• KEEP WORK AREA CLEAN. Cluttered areas invite injuries. Clear all work areas of unnecessary tools, debris, furniture, etc.

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC `

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC

Framing Nailer - LXG3000 MkII

E&OE © Unimac 4

• KEEP VISITORS AWAY. Do not let visitors handle the Nailer. All visitors should be kept safely away from work area.

• DRESS PROPERLY. Do not wear loose clothing or jewellery as they can be caught in moving parts. Rubber gloves and non-skid footwear are

recommended when working outdoors. Wear protective hair covering to contain long hair.

• CHECK PUSH LEVER BEFORE USE. Remove fuel cell and battery, and then make sure the push lever operates properly. (The push lever may

be called Safety.) Never use the Nailer unless the push lever is operating properly, otherwise the Nailer could drive a fastener unexpectedly. Do

not tamper with or remove the push lever, otherwise the push lever becomes inoperable.

• KEEP ALL SCREWS AND COVERS TIGHT IN PLACE. Keep all screws and covers tightly mounted. Check their condition periodically. Never

use the Nailer if parts are missing or damaged.

• DO NOT LOAD FASTENERS WITH TRIGGER OR PUSH LEVER DEPRESSED. When loading fasteners into the Nailer, 1) do not depress the

trigger; 2) do not depress the push lever; and 3) keep the Nailer pointed downward.

• KEEP FACE, HANDS AND FEET AWAY FROM FIRING HEAD DURING USE. Never place your face, hands, or feet closer than 8 inches (200

mm) from the firing head. A serious injury can result if the fasteners are deflected by the workpiece or are driven away from the point of entry.

• PLACE NAILER PROPERLY ON WORKPIECE. Do not drive fasteners on top of other fasteners or with the Nailer at too steep of an angle; the

fasteners can ricochet and hurt someone.

• DO NOT DRIVE FASTENERS INTO THIN BOARDS OR NEAR CORNERS AND EDGES OF WORKPIECE. The fasteners can be driven

through or away from the workpiece and hit someone.

• NEVER DRIVE FASTENERS FROM BOTH SIDES OF A WALL AT THE SAME TIME. The fasteners can be driven into and through the wall and

hit a person on the opposite side.

• CHECK FOR LIVE WIRES. Avoid the risk of severe electrical shock by checking for live electrical wires that may be hidden by walls, floors or

ceilings. Turn off the breaker switch to ensure there are no live wires.

• DO NOT OVERREACH. Keep proper footing and balance at all times.

• NEVER USE NAILER WHICH IS DEFECTIVE OR OPERATING ABNORMALLY. If the Nailer appears to be operating unusually, making strange

noises, or otherwise appears defective, stop using it immediately and arrange for repairs by an authorized service centre.

• TAKE FUEL CELL AND BATTERY OUT OF NAILER WHEN: 1) doing maintenance and inspection; 2) clearing a jam; 3) it is not in use; 4)

leaving work area; 5) moving it to another location; and 6) handing it to another person. Never attempt to clear a jam or repair the Nailer unless

you have taken fuel cell and battery out of the Nailer and removed all remaining fasteners from the Nailer. The Nailer should never be left

unattended since people who are not familiar with the Nailer might handle it and injure themselves.

• STAY ALERT. Watch what you are doing. Use common sense. Do not operate the Nailer when you are tired. The Nailer should never be used

by you if you are under the influence of alcohol, drugs or medication which makes you drowsy.

• HANDLE NAILER CORRECTLY. Operate the Nailer according to this Manual. Never allow the Nailer to be operated by children. Individuals

unfamiliar with its operation or unauthorized personnel should not be allowed to operate the Nailer.

• NEVER USE NAILER FOR APPLICATIONS OTHER THAN THOSE SPECIFIED IN THIS MANUAL.

• HANDLE NAILER CAREFULLY. Do not drop the Nailer or strike the Nailer against hard surfaces; and do not scratch or engrave signs on the

Nailer. Handle the Nailer carefully.

• MAINTAIN NAILER WITH CARE. Keep the Nailer clean and lubricated for better and safer performance.

• USE ONLY PARTS, ACCESSORIES OR FASTENERS SUPPLIED OR RECOMMENDED BY DEALER. Unauthorised parts, accessories, or

fasteners may void your warranty and can lead to malfunction and resulting injuries. Only service personnel trained by authorised service centre,

distributor or employer shall repair the Nailer.

• NEVER MODIFY OR ALTER A NAILER. Doing so may cause it to malfunction and personal injuries may result.

• Fuel cell, fuel and propellant are flammable under pressure.

• EXPLOSION / FIRE HAZARD. Failure to follow all instructions may result in fire and explosion when handling dispensers for combustible gas for

the purpose of storage, transportation, inserting into and taking out of the tool and disposal.

• DO NOT SMOKE WHEN HANDLING THE FUEL CELL.

• DO NOT INHALE ITS CONTENTS. In case of being inhaled; the person affected should be taken into the open air and brought into a

comfortable position.

• EXPANDING GASES CAUSE LOW TEMPERATURES.

• FLUID GASES MIGHT CAUSE INJURIES WHEN GETTING IN TOUCH WITH SKIN OR EYES. In case of contact with skin, wash the contact

surface carefully with warm water and soap and apply a skin cream when dry.In case of contact with eyes ; rinse the open eyes under running

water. Contact a doctor if necessary.

• STORE IN WELL-VENTILATED AREA.

• DO NOT STORE ABOVE 120°F(50°C) (E.G. DIRECT SUNLIGHT OR IN A VEHICLE).

• DO NOT EXPOSE TO AN OPEN FLAME AND SPARKS.

• DO NOT PUNCTURE OR OPEN THE FUEL CELL.

• DO NOT REFILL, RECLAIM OR RECYCLE THE FUEL CELL. Dispose according to local regulations for aerosol products.

• DO NOT DISPOSE OF FUEL CELL WITH OTHER SCRAP FOR RECYCLING.

• KEEP OUT OF REACH OF CHILDREN.

IMPORTANT SAFETY INSTRUCTIONS FOR BATTERY CHARGER

DEATH OR SERIOUS BODILY INJURY COULD RESULT FROM IMPROPER OR UNSAFE USE OF BATTERY CHARGERS. TO AVOID THESE

RI

SKS, FOLLOW THESE BASIC SAFETY INSTRUCTIONS.

• This manual contains important safety and operating instructions for battery charger.

• Before using battery charger, read all instructions and cautionary markings on: (1) battery charger; (2) battery; and (3) product using battery.

• To reduce risk of injury, charge rechargeable battery. Other type of batteries may burst causing personal injury and damage.

• Do not expose battery charger to rain or snow.

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC `

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC

Framing Nailer - LXG3000 MkII

E&OE © Unimac 5

• Use of an attachment not recommended or sold by the battery charger manufacturer may result in a risk of fire, electric shock, or injury to

persons.

• To reduce risk of damage to electric plug and cord, pull by plug when disconnecting battery charger.

• Make sure cord is located so that it will not be stepped on, tripped over, or otherwise subjected to damage or stress.

• An extension cord should not be used unless absolutely necessary. Use of improper extension cord could result in a risk of fire and electric

shock. If extension cord must be used make sure: a. That blades of extension cord are the same number, size, and shape as those of plug on

battery charger, b. That extension cord is properly wired and in good electrical condition, and c. That wire size is large enough for AC ampere

rating of battery charger as specified in Table 1.

• If the input rating of a battery charger is given in watts other than in amperes, the corresponding ampere rating is to be determined by dividing the

wattage rating by the voltage rating-for example:

• Do not operate battery charger with damaged cord or plug-replace them immediately.

• Do not operate battery charger if it has received a sharp blow, been dropped, or otherwise damaged in anyway; take it to a qualified serviceman.

• Do not disassemble battery charger; take it to a qualified serviceman when service or repair is required. Incorrect reassembly may result in a risk

of electric shock or fire.

• To reduce risk of electric shock, unplug charger from receptacle before attempting any maintenance or cleaning. Removing the battery will not

reduce this risk.

• This battery charger might be attached to the battery-operated tools as a standard accessory. In this case, please confirm Instruction Manual of

the battery-operated tools before using the battery charger.

IMPORTANT SAFETY INSTRUCTIONS FOR USE OF THE BATTERY AND BATTERY CHARGER

YOU MUST CHARGE THE BATTERY BEFORE YOU USE THE NAILER. BEFORE USING THE BATTERY CHARGER, BE SURE TO READ

AL

L INSTRUCTIONS AND CAUTIONARY STATEMENTS ON IT, THE BATTERY AND THE BATTERY CHARGER IN THIS MANUAL.

REMEMBER: USE ONLY THE BATTERY SUPPLIED BY THE MANUFACTURER. OTHER TYPES OF BATTERIES MAY BURST AND CAUSE

INJURY!

IMPROPER USE OF THE BATTERY OR BATTERY CHARGER CAN LEAD TO SERIOUS INJURY. TO AVOID THESE INJURIES:

• NEVER disassemble the battery.

• NEVER incinerate the battery, even if it is damaged or is completely worn out. The battery can explode in a fire.

• NEVER short-circuit the battery.

• NEVER insert any objects into the battery charger’s air vents. Electric shock or damage to the battery charger may result.

• NEVER charge outdoors. Keep the battery away from direct sunlight and use only where there is low humidity and good ventilation.

• NEVER charge when the temperature is below 50°F (10°C) or above 104°F (40°C).

• NEVER connect two battery chargers together.

• NEVER insert foreign objects into the hole for the battery or the battery charger.

• NEVER use a booster transformer when charging.

• NEVER use an engine generator or DC power to charge.

• NEVER store the battery or battery charger in places where the temperature may reach or exceed 104°F(40°C).

• ALWAYS operate charger on standard household electrical power (110-240 volts). Using the charger on any other voltage may overheat and

damage the charger.

• ALWAYS wait at least 15 minutes between charges to avoid overheating the charger.

• ALWAYS disconnect the power cord from its receptacle when the charger is not in use.

DISPOSAL OF THE EXHAUSTED BATTERY

• D

o not dispose of the exhausted battery. The battery can explode if it is incinerated. The product that you have purchased contains a

rechargeable battery. The battery is recyclable.

• At the end of its useful life, under various state and local laws, it may be illegal to dispose of this battery into the municipal waste stream. Check

with your local solid waste officials for details in your area for recycling options or proper disposal.

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC `

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC

Framing Nailer - LXG3000 MkII

E&OE © Unimac 6

EMPLOYER’S RESPONSIBILITIES

• Ensure that this MANUAL is available to operators and personnel performing maintenance.

• Ensure that Nailers are used only when operators and others in work area are wearing EYE PROTECTOR.

• Enforce the use of EYE PROTECTOR by operators and others in work area.

• Keep Nailers in safe working order.

• Maintain Nailers properly.

• Ensure that Nailers which require repair are not further used before repair.

SAVE THESE INSTRUCTIONS AND MAKE THEM AVAILABLE TO OTHER USERS AND OWNERS OF THIS TOOL!

Safety Symbols

The product may have safety warning labels attached to it, explained below. Understand the symbols on your

product and their meanings. If any stickers become unreadable, unattached etc., replace them.

Flammable Material Hazard

Flammable liquids, gases or

substances etc may present.

Avoid ignition sources and open

flames. Danger of fire.

Read User Manual

Read and fully understand

product safety warnings,

operation, procedures etc before

using the product.

Use Hand Protection

Wear appropriate hand protection

and take due care as the product

or use of the product may present

hand hazards.

Carbon-Monoxide Hazard

Do not use the product in

confined areas or without

adequate ventilation. Carbon-

monoxide poisoning can be fatal.

Electrocution / Electrical Shock

Hazard

High voltage or high current

electricity may be present or

required by the product. Take

due care when handling electrical

products, cables, plugs and

leads. Electrical shock can be

fatal.

Toxic Fumes / Dust Hazard

Using the product or by-products

from use may produce fumes,

smoke or particles that could be

harmful if inhaled. Wear

appropriate breathing protection

and have adequate ventilation.

Explosive Material Hazard

Combustible liquids, gases or

substances etc may be present.

Avoid ignition sources and open

flames. Danger of explosion.

Cutting / Amputation Hazard

The product may have blades,

edges or mechanical devices that

can cause severe cut injury to

fingers, limbs etc. Take due care

when handling and using the

product.

Crush Hazard

The product may have blades,

edges or mechanical devices that

can cause severe crush injury to

fingers, limbs etc. Take due care

when handling and using the

product.

Single Operator Only

The product must be operated by

a single person only. More than

one person operating the product

may introduce additional hazards.

Use Face Protection

Wear appropriate full-face

protection and take due care as

the product or use of the product

may present face and eye

hazards.

Use Foot Protection

Wear appropriate foot protection

and take due care as the product

or use of the product may present

foot hazards.

Use Eye / Ear / Head Protection

Wear appropriate eye and / or

ear and / or head protection and

take due care as the product or

use of the product may present

eye, hearing and head hazards.

Running Hazard

Do not run on or near the product

as doing so may present a fall

hazard.

Diving Hazard

Do not dive into the product as

doing so may present a neck /

head injury hazard.

Adult Supervision Required

Always supervise children and

other users of a product to

prevent drowning or injury.

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC `

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC

Framing Nailer - LXG3000 MkII

E&OE © Unimac 7

Skin Penetration / Puncture

Hazard

The product may produce

pressure, emit liquids or objects

that can cause severe injury to

fingers, limbs, blood etc. Take

due care when handling and

using the product.

Hot Surface Hazard

Be aware that the product may

produce high temperatures and

hot surfaces that can cause burn

injuries.

Flying Debris Hazard

Be aware that the product or use

of the product may present

hazards produced by flying

debris. Wear appropriate clothing

and protective devices.

Moving Parts Hazard

Be aware that the product

contains or uses mechanical

devices that move or rotate.

Always wait for moving parts to

stop fully before handling the

product, adjusting, maintenance

etc.

Carbon-Monoxide Hazard

Do not use the product in

confined areas or without

adequate ventilation. Carbon-

monoxide poisoning can be fatal.

Pull Hazard

Be aware that the product

contains or uses mechanical

devices that can pull in objects

and can cause severe injury to

fingers, limbs etc. Take due care

when handling and using the

product.

Slope / Fall Injury Hazard

Be aware that using the product

on sloping surfaces or in slippery

conditions may present additional

dangers from falls and contact

with blades, moving parts, hot

surfaces etc.

"Slam Dunk" Warning

Do NOT attempt "slam dunk"

manoeuvres as this may result in

severe injury due to falling,

product breakage or collapse etc.

Electrocution / Electrical Shock

Hazard - Outdoor

High voltage or high current

electricity may be present or

required by the product. Do NOT

use in rain, damp or wet

conditions. Electrical shock can

be fatal.

Electrocution / Electrical Shock

Hazard - Disconnect

High voltage or high current

electricity may be present or

required by the product. Always

disconnect the product from the

electrical supply before handling

the product, adjusting,

maintenance etc.

Power Line Electrocution

Hazard

High voltage / high current power

lines may be present. Use

extreme caution to avoid contact

or interference with power lines.

Electrical shock can be fatal.

"Kick-Back" Hazard

High level of "kick-back" hazard

that can cause the machine to

suddenly rotate towards operator.

Kick-back injury can be fatal.

Winch Operator Position

Hazard

Do NOT stand between winch

and load. Do NOT use winch to

move people.

Winch Lift Hazard

Do NOT LIFT load vertically. Use

machine to PULL only.

Cable Hazard

Ensure that load bearing cable is

not kinked or knotted.

Winch Cable Hazard

Ensure that there is a minimum

number of cable coils on

winching mechanism.

Winch Hook Hazard

Carry hook to load – do NOT

throw or run.

Flash / Blinding Hazard

Wear appropriate eye protection

for welding. Direct exposure to

weld arcs may cause permanent

eye injury.

Laser Hazard

Laser may be in use – do NOT

look directly at laser or allow

others to.

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC `

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC

Framing Nailer - LXG3000 MkII

E&OE © Unimac 8

Table of Contents

Safety .................................................................................................................................................... 2

Safety Symbols .................................................................................................................................................... 6

Parts Identification ................................................................................................................................ 9

Operation ............................................................................................................................................ 10

Nail Selection..................................................................................................................................................... 10

Applications ....................................................................................................................................................... 10

Removal and Installation Method of Battery ....................................................................................................... 10

Charging Method ............................................................................................................................................... 11

Before Operation ............................................................................................................................................... 12

Working Environment .................................................................................................................................. 12

Cold Weather Care ...................................................................................................................................... 13

Preparing the Fuel Cell ................................................................................................................................ 13

Preparing the Battery ................................................................................................................................... 14

Testing the Nailer ........................................................................................................................................ 15

Loading Nails............................................................................................................................................... 19

Operating the Nailer ........................................................................................................................................... 21

Methods of Operation ........................................................................................................................................ 21

Adjusting the Nailing Depth ................................................................................................................................ 22

Using the Hook .................................................................................................................................................. 23

Clearing a Jam .................................................................................................................................................. 23

Lithium Battery Care and Maintenance............................................................................................... 25

Top 3 Battery Care Requirements ...................................................................................................................... 25

Maintenance ........................................................................................................................................ 27

Inspecting the magazine .................................................................................................................................... 27

Storing ............................................................................................................................................................... 27

Services and Repairs ......................................................................................................................................... 28

Maintenance Schedule ...................................................................................................................................... 28

Troubleshooting .................................................................................................................................. 29

Specifications ..................................................................................................................................... 30

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC `

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC

Framing Nailer - LXG3000 MkII

E&OE © Unimac 9

Parts Identification

Cover

Handle

Battery

compartment

(opposite side)

Battery indicator

(LED)

Magazine

Trigger

Feeder knob

Push lever

Driver blade

Piston

Chamber

Spark plug

Top cover

Latch

Terminal hole

Connector plug

Green indicator light

Red indicator light

Power adaptor

Spare parts available

for purchase, scan QR

code below:

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC `

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC

Framing Nailer - LXG3000 MkII

E&OE © Unimac 10

Operation

Nail Selection

WARNING! Be sure to use the high-quality nails. The use of any other bad nails can result in tool

malfunction and/or nail breakdown, leading to serious injuries. Only nails shown in the Table

below can be driven with this Nailer. This Nailer is not recommended for use with 3 to 3 ½ ring shank

nails in pressure-treated lumber.

Applications

•

Floor and wall framing.

•

Truss build-up, Window build-up.

•

Sub flooring and roof decking.

•

Wall sheathing.

•

Mobile home and modular housing construction.

Removal and Installation Method of Battery

How to install the battery:

Align the battery with the groove in tool handle and slip it into place. Always insert it all the way until it locks in

place with a little click. If not, it may accidentally fall out of the tool, causing injury to you or someone around you.

How to remove the battery:

Withdraw battery from the tool handle while pressing the latch on the side of the battery.

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC `

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC

Framing Nailer - LXG3000 MkII

E&OE © Unimac 11

Charging Method

WARNING! Before plugging into the power source, make sure that the power source voltage is

stated on the nameplate and the cord is not damaged. Do not charge at voltage higher than

indicated on the name plate. If charged at voltage higher than indicated on the nameplate, the charger

will burn up. Do not use the electrical cord if damaged. Have it repaired or replaced immediately.

1. Insert the battery into the battery charger. Make sure it contacts the bottom of the battery charge.

2. Insert the connector plug of the power adaptor into the socket of the charger.

3. Insert the plug of the power adaptor into the power source.

4. C

harging:

− When the plug of the battery charger has been inserted into the power source, charging will commence,

and the red indicator light will turn on.

NOTE: If the indicator light does not turn on, pull out the plug from the power source and check if the

battery is properly mounted.

− In approx. 120 min. at 70° F (20°C), when the battery is fully charged, the green indicator light will turn

on.

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC `

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC

Framing Nailer - LXG3000 MkII

E&OE © Unimac 12

NOTE: The battery charging time becomes longer when ambient temperature is low, or the voltage of the

power source is too low. When the green indicator light does not turn on even if more than 100min. has

passed after the start of charging, stop charging and contact your local authorised service centre.

5. Disconnect the battery charger from the power source.

CAUTION! Do not pull the plug out of the power source by pulling on the cord. Make sure to grasp the plug

when removing from the power source to avoid damaging the cord.

6. Remove the battery from the battery charger. Supporting the battery charger with your hand, pull out the

battery from the battery charger.

Regarding electric discharge in case of new batteries, etc.:

As the internal chemical substance of new batteries and batteries that have not been used for an extended

period is not activated, the electric discharge might be low when using them the first and second time. This is a

temporary phenomenon, and normal time required for recharging will be restored by recharging the batteries 2 -

3 times.

How to make the batteries perform longer:

•

Recharge the batteries before they become completely exhausted. When you feel that the power of the tool

becomes weaker, stop using the tool and recharge its battery. If you continue to use the tool and exhaust the

electric current, the battery may be damaged, and its life will become shorter.

•

Avoid recharging at high temperatures. A rechargeable battery will be hot immediately after use. If such a

battery is recharged immediately after use, its internal chemical substance will deteriorate, and the battery

life will be shortened. Leave the battery and recharge it after it has cooled for a while.

CAUTION!

•

When the battery charger has been continuously used, the battery charger will heat up, thus constituting the

cause of the failures. Once the charging has been completed, give it 15 minutes to cool down until the next

charging.

•

If the battery is recharged when it is warm due to battery use or exposure to sunlight, the indicator lights may

not turn on.

•

The battery should not be recharged. In such a case, let the battery cool down before charging.

•

If the battery charger does not work while the battery is mounted correctly, it is probable that the battery or

charger is malfunctioning. Take it to your authorised Service centre.

The charging time should not exceed 24 hours, or the battery could get damaged, or even

explode!

Before Operation

Read the Safety section first!

Working Environment

•

No flammable gas, liquid or other flammable objects at worksite.

•

Use outdoor or well-ventilated areas.

•

Do not inhale fumes or smoke.

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC `

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC

Framing Nailer - LXG3000 MkII

E&OE © Unimac 13

•

Keep the Nailer, fuel cell and battery away from temperatures exceeding 120°F (50°C).

•

Keep away from ignition sources.

•

No smoking.

•

Clear the area of children or unauthorised personnel.

Cold Weather Care

•

Do not store the Nailer, fuel cell and battery in a cold weather environment. Keep the Nailer, fuel cell and

battery in a warm area until beginning the work.

•

If the Nailer, fuel cell and battery are already cold, bring it in a warm area and allow the Nailer to warm up

before use. Observe temperature limit of max. 120°F (50°C).

•

Do not expose to an open flame or sparks!

CAUTION!

•

The Nailer may not drive completely below when, at low temperature fuel cell is loose the required propellant

force, at high temperature fuel cell can overdose.

•

Do not use the Nailer in the rain or where excessive moisture is present.

•

The Nailer is not recommended for use at altitudes above 5,000 feet (1,500 m), or in temperature below

30°F(0°C).

Preparing the Fuel Cell

DANGER! The fuel cell is flammable. Keep away from ignition sources. Do not spray to a naked

flame or any incandescent material. Do not smoke when handling fuel cell. Keep stem of fuel cell

away from face or skin. Expanding gases cause low temperatures. Do not contact with gases. Do not

inhale. Keep out of reach of children.

CAUTION! If the gas leaks from the metering valve or the gas cartridge after attached the metering valve,

replace with the new metering valve. Do not attempt to reuse the metering valve. Replace with the new

metering valve.

•

Please use special fuel cell for gas nailer (long 165mm, capacity 40g/80ml).

•

The main component of fuel cell is liquid hydrocarbon (propane, butane).

To attach the metering valve to a fuel cell:

1. Separate the metering valve and the cap from the gas cartridge.

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC `

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC

Framing Nailer - LXG3000 MkII

E&OE © Unimac 14

2. Press forward (stem side) and downward on the front side of the metering valve.

3. Press downward on the rear of the metering valve until it seals.

Fuel Cell Compatibility:

IMPORTANT: If you are using the FC165 fuel cell, it will come with a black protective cover, you must

remove it before inserting it into the nail gun.

If you are using the Paslode B20543F cannister, you will need to use the included black metering valve

which can be found inside the nail guns carton.

Preparing the Battery

•

Read

Safety section first.

•

You must charge the battery before use. Read

charging method of battery.

Video Tutorial:

Installing The Metering

Valve for Paslode Canisters

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC `

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC

Framing Nailer - LXG3000 MkII

E&OE © Unimac 15

Testing the Nailer

DANGER! Operators and others in work area MUST wear safety glasses with side shields which

conforms to ANSI Z87.1 specifications. Never use Nailer unless push lever is operating properly.

Do not throw the push lever tip onto wood.

The machine employs a preventive mechanism for unloaded operation. The machine enters a state where the

push lever cannot be pushed up. This takes place when the magazine is not loaded with nails or when the

remaining number of nails becomes less than 7 or 8.

Before beginning any nailing work, test the Nailer by using the checklist below. Conduct the tests in the following

order. If abnormal operation occurs, stop using the Nailer and contact a local authorised service centre

immediately.

1. Remove all nails, fuel cell and battery from nailer.

All screws must be tightened.

The push lever and trigger must move smoothly with pulling back the feeder knob.

2. Installing the battery.

Do not operate the push lever or trigger while installing the battery. Make sure the battery indicator light is

flashing green. If the battery indicator light is flashing red, the battery does not have enough power and it

needs to be charged.

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC `

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC

Framing Nailer - LXG3000 MkII

E&OE © Unimac 16

Battery indicator lights:

Flashing GREEN: Enough power remaining (The light turns steady during operation).

Flashing RED: Insufficient power remaining.

Fast flashing RED: The motor has short circuited.

3. Insert fuel cell into nailer.

a. Pull the latch and open the cell cover.

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC `

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC

Framing Nailer - LXG3000 MkII

E&OE © Unimac 17

b. Insert the fuel cell into nailer.

c. Insert the stem of fuel cell into the hole of adaptor.

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC `

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC

Framing Nailer - LXG3000 MkII

E&OE © Unimac 18

d. Close the cell cover.

4. Remove your finger from the trigger and press the push lever against the workpiece with pulling back the

feeder knob. The nailer must not be operating.

5. Separate the push lever from the workpiece. Next, point the nailer downward, pull the trigger and then wait in

that position for 5 seconds or longer. The nailer must not be operating.

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC `

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC

Framing Nailer - LXG3000 MkII

E&OE © Unimac 19

6. Without touching the trigger, press the push lever against the workpiece. Pull the trigger. The nailer should

operate.

7. If no abnormal operation is observed, you may load nails in the Nailer. To drive nails into the workpiece,

follow the above steps in the actual application. The nailer must operate properly.

Loading Nails

WARNING! When loading nails into the Nailer: 1) do not depress trigger; 2) do not depress push

lever; and 3) keep Nailer pointed downward.

2-Action Nail Feeding:

1. Pull the feeder knob to the bottom of the magazine until the feeder is locked.

2. Insert nail strip into the back of the magazine.

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC `

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC

Framing Nailer - LXG3000 MkII

E&OE © Unimac 20

3. Press down the feeder and push the feeder knob, the feeder will push nails.

NOTE: Gently push the nail feeder and feeder knob against the nail. If the nail feeder and feeder knob are

released from the backward magazine and bumped against the nail, the connecting paper of the nail can be

damaged. Use nail strip of more than 10 nails. The Nailer is now ready to operate.

Removing the nails:

Pull the feeder knob to the bottom of the magazine until the feeder is locked.

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC `

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC

Framing Nailer - LXG3000 MkII

E&OE © Unimac 21

Operating the Nailer

DANGER! Operators and others in the work area MUST wear safety glasses with side shields

which conforms to ANSI Z87.1 specifications. Never use in presence of flammable liquids or

gases. Do not touch around the exhaust outlet with bare hands. The push lever and nose will become

hot and get heated up after prolonged or rapid use. Explosion and fire hazard! Keep away from sunshine

and from temperature exceeding 120°F(50°C). Keep away from ignition source. No smoking.

WARNING! NEVER point tool at yourself or others in work area. Keep fingers AWAY from trigger

when not driving nails to avoid accidental firing. Use outside or well-ventilated area. Do not

inhale its exhausts. Do not use the electrical cord if damaged. Have it repaired immediately. Never place

your face, hands, or feet closer than 8 inches (200 mm) from firing head when using. Do not drive nails

on the top of other nails or with Nailer at too steep of an angle; nails can ricochet and hurt someone. Do

not drive nails into thin boards or near corners and edges of workpiece. Nails can be driven through or

away from workpiece and hit someone. Never drive nails from both sides of a wall at the same time.

Nails can be driven into and through the wall and hit a person on the opposite side. Never use Nailer

which is defective or operating abnormally. Do not use Nailer as hammer. Disconnect battery and fuel

cell from Nailer when: 1) it is not in use; 2) leaving work area; 3) moving it to another location; and 4)

handing it to another person. Be careful of unwanted fastener. If pulling the trigger more when not

driving nail at the temperature below 30°F (0°C), an wanted fastener will be driven.

This Nailer is equipped with a full sequential actuation electron control:

•

First, press the push lever against the workpiece.

•

next, pull the trigger to drive a nail. The machine employs a preventive mechanism for unloaded operation.

The machine enters a state where the push lever cannot be pushed up. This takes place when the magazine is

not loaded with nails or when the remaining number of nails becomes less than 7 or 8.

CAUTION! Do not throw the push lever tip onto wood when the push lever cannot be pushed up.

Methods of Operation

CAUTION! Squeeze the trigger when driving a nail, otherwise the piston cannot return to its

original position correctly. Make sure the nailing depth when the temperature is above 85°F

(30°C) or below 50°F (10°C).

This Nailer is equipped with the push lever and does not operate unless the push lever is depressed (upward

position). It has an intermittent operation (trigger fire) only.

1. Position the nail outlet on the workpiece with your finger off the trigger.

2. Depress the push lever firmly until it is completely depressed.

3. Pull and squeeze the trigger to drive a nail.

4. Remove finger from the trigger.

To continue nailing in other places, move the nailer along the wood, repeating steps 1 - 4 as required.

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC `

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC

Framing Nailer - LXG3000 MkII

Adjusting the Nailing Depth

To assure that each nail penetrates to the same depth, ensure that the Nailer is always held firmly against the

workpiece. If nails are driven too deep or shallow into the workpiece, adjust the nails in the following order.

1. Remove the fuel cell and the battery from the Nailer.

2. Loosen the bolt with an allen key.

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC `

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC

Framing Nailer - LXG3000 MkII

3. If nails are driven too deeply, move the push lever forward.

If nails are driven too shallow, move the push lever to backward.

4. Stop moving the push lever when you reach a suitable position for a nailing test.

5. Connect the fuel cell and the battery to the Nailer. ALWAYS WEAR SAFETY GLASSES. Perform a nailing

test.

6. Remove the fuel cell and the battery from the Nailer.

7. Choose a suitable position for adjusting.

Using the Hook

CAUTION! If the tool is dropped, there is a risk of malfunction and/or physical damage can occur. It is

recommended that you also use fall-preventing wires, etc. When using the Hook, pull it out from the magazine.

When not using it, insert it in the magazine.

Clearing a Jam

If nails are jammed in the nose, remove it, and adjust the nailing in the following order.

1. Remove the fuel cell and the battery from the Nailer.

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC `

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC

Framing Nailer - LXG3000 MkII

2. Lock the feeder in the magazine bottom and remove fasteners.

3. Press the magazine locker, pull the magazine out of the nose and clear the jam.

4. Insert the magazine into the nose and lock the magazine locker to the handle.

5. Connect the fuel cell and the battery to the Nailer. ALWAYS WEAR SAFETY GLASSES.

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC `

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC

Framing Nailer - LXG3000 MkII

Lithium Battery Care and Maintenance

Top 3 Battery Care Requirements

6. Charge battery before first use. The battery may arrive with some charge, regardless of this the

battery must be charged for a maximum 2 hours on the initial charge and a maximum 2 hours for

each subsequent charge.

7. Charge battery immediately when it is depleted. Do not store a depleted battery. This will

permanently impact the life of the battery. If the battery is going to be stored for a period of time, fully

charge the battery before storing.

8. Disconnect battery when not in use. To prolong the life of a battery, disconnect it from the unit

when not in use. Disconnect chargers from the battery once charged.

To ensure the battery maintains optimum performance, follow the guidelines outlined below.

•

For best results, charge batteries in temperatures between 10°C and 30°C

•

When battery is charged, disconnect the charger from the power supply and remove the battery from the

charger.

•

If a battery is stored or otherwise unused for an extended period, and the battery has no charge remaining

when you check it, consider it to be damaged. Do not attempt to recharge it or to use it. Replace it with a

new battery.

•

Use only with the battery charger specified by the manufacturer.

•

Ensure that the battery charger electrical cord is not subjected to damage or stress. Do not operate the

battery charger if it has a damaged electrical cord or plug.

•

Do not use the charger in wet areas or expose it to rain or water.

•

The typical estimated life of a Lithium-Ion battery is about two to three years or 300 to 500 charge cycles,

whichever occurs first. One charge cycle is a period of use from fully charged, to fully discharged, and fully

recharged again

•

Explosion hazard – protect the battery against heat; for example, direct sunlight and fire. Do not store

batteries in vehicles or locations subject to heat.

•

Batteries can explode in the presence of an ignition source, such as a pilot light. To reduce the risk of

serious personal injury, never use any cordless product in the presence of open ﬂame. Exploding batteries

can propel debris and chemicals.

•

Do not open the battery – danger of short-circuiting and/or explosion.

•

Do not attempt to destroy or disassemble the battery pack or remove any of its components.

•

Do not touch the battery terminals with metal objects and/or body parts as short-circuit and/or personal injury

may result.

•

Explosion hazard – do not open and/or short-circuit the battery.

•

Poison hazard – battery leakage (liquid ejection). Under extreme conditions, liquid may be ejected from the

battery – avoid contact. If contact accidentally occurs, immediately seek medical attention, and flush with

water. If liquid contacts eyes, immediately seek medical attention, flush with clean water for at least 10

minutes. Liquid ejected from the battery may cause irritation or burns.

•

Dispose of non-serviceable batteries in an environmentally responsible manner and according to local

regulations.

Failure to adhere to the requirements above may result in the battery becoming inoperative or battery life being

reduced. In extreme cases or abuse, battery overheating or fire may result.

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC `

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC

Framing Nailer - LXG3000 MkII

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC `

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC

Framing Nailer - LXG3000 MkII

Maintenance

NOTE: The information contained in this Manual is designed to assist you in the safe

maintenance of the Nailer. Read the Safety section.

DANGER! Never use and test in presence of flammable liquids or gases. Keep away from ignition

sources. No smoking.

WARNING! Remove fuel cell, battery and all the nails from the Nailer when: 1) doing maintenance and

inspection; and 2) clearing a jam.

Inspecting the magazine

1. Remove fuel cell and battery.

2. Clean the magazine. Remove paper chips or wooden chips which may have accumulated in the magazine.

Lubricate it with a gas tool lubricant.

CAUTION! Check if the nail feeder slides smoothly by pulling it with a finger. If it’s not smooth,

nails can be driven at an irregular angle and hurt someone.

Storing

DANGER! Store nailer properly with fuel cell and battery removed. The fuel cell is an aerosol

dispenser with flammable contents. When not in use, the nailer, fuel cell and battery should be

stored in a tool case and in a cool, dry place. Store indoors at temperature below 120°F (50°C).

•

When not in use for an extended period, apply a thin coat with the lubricant to the steel parts to avoid rust.

•

Do not store the Nailer, fuel cell and battery in a cold weather environment. Keep them in a warm area.

•

When not in use, the Nailer, fuel cell and battery should be stored in a warm and dry place. Keep it out of

reach of children.

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC `

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC

Framing Nailer - LXG3000 MkII

Services and Repairs

CAUTION! Repair, modification, and inspection of this tool must be carried out by an authorised

service centre. Use only parts supplied or recommended by local dealer for repair.

All quality Nailers will eventually require servicing or replacement of parts because of wear from normal use.

Maintenance Schedule

Action Reason Method

Clean the magazine and the feeder

mechanisms.

Prevent jams. Blow-clean daily.

Keep the push lever working properly.

Promotes operator safety and efficient

nailer operation.

Blow-clean daily.

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC `

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC

Framing Nailer - LXG3000 MkII

Troubleshooting

Problems Possible Reasons Possible Solutions

Nailer operates, but no nail is being

driven.

Check for jams. Clear the jam.

Check the function of the feeder. Clean and lubricate.

Is the coil spring weakened or

damaged?

Replace coil spring.

Check for proper nails. Use only recommended nails.

Check if the driver blade piston is

down or not.

Push the driver blade with a slotted

screwdriver and put back the piston to

the highest position.

Skipping nails. Intermittent feed.

Check for proper nails. Use only recommended nails.

Check the function of the feeder. Clean and lubricate.

Is the coil spring weakened or

damaged?

Replace coil spring.

Feeder worn or damaged? Replace feeder.

Check for returning of piston.

Pull the trigger all the way.

Too low temperature, warm up fuel

cell under 120°F (50°C).

Check for smooth movements of the

piston.

Contact an authorised service centre

for replacements.

Replace piston seal steel ring.

Replace piston assembly.

Replace cylinder seal steel ring.

Nails jam. Driven nail is bent.

Check for proper nails. Use only recommended nails.

Driver blade worn?

Contact an authorised service centre

for replacements.

Feeder worn or damaged? Replace feeder.

The operation of the push lever is

not smooth.

Push lever bent?

Contact an authorised service centre

for replacements.

Check push lever’s moving track, are

there debris?

Contact an authorised service centre

for replacements.

Fan is working, light indicator

shows GREEN, yet it doesn’t drive a

nail or operation unstable.

Check for returning of piston. Pull the trigger all the way.

Check fuel cell, insufficient? Exchange it with a new fuel cell.

Check spark plug wire, worn out?

Contact an authorised service centre

for replacements.

Check spark plug, grease, or debris?

Contact an authorised service centre

for replacements.

Check filter, is it clogged?

Contact an authorised service centre

for replacements.

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC `

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC

Framing Nailer - LXG3000 MkII

Problems Possible Reasons Possible Solutions

Fan does not operate when push

lever is pressed.

Magazine is empty. Load more nails in the magazine.

Note the colour of the light indicator.



If red: charge the battery.



If green: Contact an authorised

service centre for replacements.

Fan does not work, light indicator

flashes RED quickly (5Hz).

-

Motor failure; contact an authorised

service centre for replacements.

Unable to charge the battery. - Check the electrical cord.

Other control malfunction. - Remove the battery and reinstall it.

Specifications

Degree 34°

Nail range (mm) From 2" (50mm) to 3-1/2" (90mm)

Nail capacity 57

Cycle rate 2-3 nails per second

Batteries Li-ion Battery 7.4V 1.5Ah

Charger input power Ac110-240v 50~60hz

Charging time 120min (5 min. Can shot 200 nails)

Joules 100

Boasting rate (nails per hr.) 1000

Boasting rate (shots per charge) 2800

Plug SAA

Cord length 145cm

Motor Brushless motor for long lifespan

Quick removal magazine function Yes, install and remove the magazine quickly to clear the jam

Power

The power is about 100J. It can shoot 85mm smooth nails into hard

wood completely.

Rubber cover on nose to protect the wood

surface

Yes

Comfortable elastomer grip handle Yes

Triple press-hardened drive blade Yes

Compatible Cannisters



Fuel Cell FC165



Paslode B20543F

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC `

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC

Some experts believe that the incorrect or prolonged use of almost any

product may cause serious injury or death. To help reduce your risk of

serious injury or death, refer to the information below. For more information,

see www.datastreamserver.com/safety



Consult all documentation, packaging

and product labelling before use. Note

that some products feature

documentation available online. It is

recommended to print and retain the

documentation.



Before each use, check the product for

loose/broken/damaged/missing parts,

wear or leaks (if applicable). Never use a

product with

loose/broken/damaged/missing parts,

wear or leaks.



Products must be inspected and serviced

(if applicable) by a qualified technician

every 6 months. This is based on

average residential use by persons of

average size and strength, and on a

property of average metropolitan size.

Use beyond these recommendations may

require more frequent

inspections/servicing.



Ensure that all users of the product have

completed a suitable industry recognised

training course before being allowed

access to the product.



The product has been supplied by a general merchandise

retailer that may not be familiar with your specific

application or description of application. Be sure to attain

third-party approval from a qualified specialist for your

application before use, regardless of any assurances from

the retailer or its representatives.



This product is not intended for use where fail-safe

operation is required. As with any product (for example,

automobile, computer, toaster), there is the possibility of

technical issues that may require the repair or

replacement of parts, or the product itself. If the possibility

of such failure and the associated time it may take to

rectify could in any way inconvenience the user, business

or employee, or financially affect the user, business or

employee, then the product is not suitable for your

requirements. This product is not intended for use where

incorrect operation or a failure of any kind, including but

not limited to, a condition requiring product return,

replacement, parts replacement or service by a technician

may cause financial loss, loss of employee time or an

inconvenience requiring compensation.



If this product has been purchased in error when

considering the information presented here, contact the

retailer directly for details of their returns policy, if

required.

diagrams or images may be reproduced or transmitted in any form or by any means, electronic or

mechanical, including photocopying, scanning or recording, or any information storage and retrieval system,

without express permission or consent from the publisher.

UNIMAC NALGASUMCA34E LXG3000 MkII Gas Framing Nail Gun, Commercial Brushless

Product's Documents

Product manual

Specifications

UNIMAC NALGASUMCA34E Questions and Answers