SEALEY 90PC JUNIOR TOY TOOL KIT WITH
WORK BENCH
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
instruction
manual
JTK2 Issue:1 27/09/24
Original Language Version
© Jack Sealey Limited
1. SAFETY
WARNING! This product is unsuitable for children under the age of 3 years of age EN 71-1 Compliant.
WARNING! To be used under the supervision of an adult.
WARNING! Assembly should be completed by adults only.
WARNING! The hat and goggles are only a toy, and therefore do not provide protection.
WARNING! The hat and goggle labels must be applied to the product.
WARNING! Failure to follow the precautions in the instructions will expose the user to hazards.
9 Inspect tools regularly to ensure that they are in an adequate condition for safe use.
9 Prevent unintentional starting. Ensure the drill batteries are removed when not in use.
8 DO NOT attempt to try and charge the battery pack on any of the range of Sealey main line chargers. It is not compatible.
9 Only batteries of the same or equivalent type, as recommended, are to be used.
8 DO NOT dispose of batteries in re, as batteries may explode or leak.
8 DO NOT mix old and new batteries or types of batteries (i.e. alkaline/standard/rechargeable).
WARNING! Non-rechargeable batteries are not to be recharged.
WARNING! The supply terminals are not to be short-circuited.
WARNING! Rechargeable batteries are only to be charged under adult supervision.
WARNING! Batteries are to be inserted with the correct polarity.
9 Recycle or dispose of used batteries as stipulated by local regulation.
8 DO NOT allow a child to put any of the toy tool set in their mouth small parts could be a choking hazard.
8 DO NOT leave near an exposed heat source or naked ame.
8 DO NOT get the drill or batteries wet or use in damp or wet locations.
8 DO NOT submerge in water or liquids.
8 DO NOT drop or throw the drill or components.
8 DO NOT use tool set unless you have been instructed in its use by a parent or guardian.
9 After use clean, inspect for damage and store in a safe, dry, location.
9 Only for domestic use.
2. INTRODUCTION
All the basics for every budding builder to be able to help with DIY tasks around the home, complete with workbench. Battery powered
drill supplied with three attachments. For added realism the drill is tted with a working light as well as forward and reverse motion
for a range of purposes (requires 3 x AA batteries - not included). Suitable for children 3+ years old, EN 71-1 compliant. Contents:
Workbench, Screwdriver (x2), Adjustable Wrench, Pliers, Hammer, Saw, Electric Drill with Assorted Drill Bits, Spanner (x2), Nuts (x20),
Bolts (x20), Pre-drilled Blocks (x3), Pre-Drilled shapes (x6), Hooks (x10), Hat, Goggles, Double-Sided Tape Measure, Tray, T-Wrench,
Plugs (x2), Vice.
3. SPECIFICATION
Not suitable
for children
under 3
MODEL NO: JTK2
Model No: JTK2
Nett Weight: 1.83kg
Contents: Workbench, Screwdriver (x2),
Adjustable Wrench, Pliers,
Hammer, Saw, Electric Drill with
Assorted Drill Bits, Spanner (x2),
Nuts (x20), Bolts (x20), Pre-drilled
Blocks (x3), Pre-Drilled Shapes
(x6), Hooks (x10), Hat, Goggles,
Double-Sided Tape Measure,
Tray, T-Wrench, Plugs (x2), Vice.
JTK2 Issue:1 27/09/24
Original Language Version
© Jack Sealey Limited
4. ASSEMBLY
1. Insert the 4 work bench legs into the underside of the work bench. 2. Attach front and rear cross supports using supplied nuts and
bolts. Use the 4th hole in the work bench legs as shown.
3. Attach the cross supports to the side of the work bench legs using the supplied nuts and bolts. Use the 3rd hole as shown. 4. Turn
work bench over onto it’s feet. Click the back into position as shown.
5. Insert a nut into the rear section of the rear jaw. Place the rear jaw section into the vice and turn the threaded screw to assemble. 6.
Bolt the vice to the work bench using 4 nuts and bolts as shown.
5. OPERATION
5.1. FITMENT OF BATTERIES
5.1.1. To t batteries see g.1 and g.2. To remove the batteries in their pack from the equipment, depress the spring loaded button on the
battery pack. Remove the battery pack by sliding out. DO NOT touch the metal battery terminals.
5.1.2. Remove screw (Fig.1) and then remove battery cover (Fig.2).
5.1.3. Fit AA batteries x3 starting from spring end negative - (Fig.2) compressing spring and then slotting battery positive end + into the metal
tipped end (Fig.2). ’Remove exhausted batteries from the drill to prevent damage. Remove the batteries from the unit during extended
periods of non-use’.
5.2. USING THE DRILL
5.2.1. Ensure that you have read, understood and comply with all the safety instructions in section 1.
5.2.2. Refer to g.3 and g.4 for use.
6. MAINTENANCE
6.1. CLEANING AND CARE
6.1.1. Remove dirt with a damp soft cloth or sponge. DO NOT use water or liquids on the drill.
6.1.2. Retain the packaging and instructions as it contains important information.
5
Rear jaw
Vice
Nut
6
g.1
Forward, reverse
switch
g.2 g.3
g.4
Speed control
2 21
1 12
2
1
Press button for release
of battery pack
Trigger
1
2 3 4
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 sales@sealey.co.uk www.sealey.co.uk
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
WEEE REGULATIONS
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment
(WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid
waste authority for recycling information.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted,
taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product
becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and
dispose of the product and fluids according to local regulations.
JTK2 Issue:1 27/09/24
Original Language Version
© Jack Sealey Limited
REGISTER YOUR
PURCHASE HERE
