SV20 SERIES FAST CHARGE BATTERY
CHARGER 20V - EUROPEAN PLUG
MODEL NO: CP20VMCEU
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS &
CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO
SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE
FOR FUTURE USE.
1. SAFETY
1.1. GENERAL SAFETY
9 Children from age 8 years and above, persons with reduced physical, sensory, or mental capabilities those with lack of experience and
knowledge can use the appliance, if they have been given supervision or instruction concerning use of the appliance in a safe way to
understand the hazards involved.
8 Children shall NOT play with the appliance.
8 Cleaning and user maintenance on the appliance shall NOT be made by children without supervision.
9 The appliance shall be disconnected from its power source during service and when replacing parts.
9 If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualied persons in order to avoid
a hazard.
1.2. ELECTRICAL SAFETY
WARNING! It is the user’s responsibility to check the following:
9 Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs
and all electrical connections for wear and damage. Sealey recommend that an RCD (Residual Current Device) is used with
all electrical products.
Electrical safety information. It is important that the following information is read and understood:
9 Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
9 Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
Important: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is tted with the correct fuse.
8 DO NOT pull or carry the appliance by the power cable.
8 DO NOT pull the plug from the socket by the cable.
8 DO NOT use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired or is replaced immediately
by a qualied electrician.
If the cable or plug is damaged during use, switch o the electricity supply and remove from use.
Ensure that repairs are carried out by a qualied electrician.
1.3. BATTERY CHARGER SAFETY INSTRUCTIONS
WARNING! DO NOT use the charging base to charge any battery other than those specically stated. Other types of batteries may explode.
WARNING! DO NOT recharge non-rechargeable batteries.
9 Inspect the plug, cable and the charging base for wear and damage to ensure items are safe before connecting to the mains power
supply. If worn or damaged DO NOT use, immediately replace, or contact a qualied electrician.
9 Check cables are always protected against short circuit and overload.
9 Uncoil the power cable between the plug and the charging base before use.
8 DO NOT pull or carry the charging base by the charger power lead, or pull the plug from the mains socket by the power lead.
8 DO NOT use any other type of transformer with the charging base.
8 DO NOT try to open or dis-assemble the plug or charging base.
8 DO NOT use the plug to power any other electrical item.
9 Disconnect the charging base from the mains power supply when not in use.
8 DO NOT expose the charging base to damp or wet conditions (for indoor use only).
8 DO NOT operate the charging base if it has been dropped, or has received a sharp knock, or is damaged. Contact an authorised
service agent.
8 DO NOT dismantle the charging base as this may cause damage or personal injury and will invalidate your warranty.
8 DO NOT insert foreign objects or material into the slot reserved for the battery.
8 DO NOT immediately charge a second battery. Consecutive charging will overheat the charging base. Allow the unit to cool for 15
minutes before charging the next battery.
9 Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
9 Ensure that cables are always protected against short circuit and overload.
8 DO NOT use worn or damaged cables, plugs or connectors. Immediately have any faulty item replaced by a qualied electrician.
1.4. BATTERY SAFETY PRECAUTIONS
WARNING! Batteries contains Lithium-ion which is dangerous. Handle with care to avoid damage, re, corrosion or personal injury.
9 Charge battery prior to its rst use. The battery will have been shipped in a low charge state. To reduce the risk of burns or re:
8 DO NOT attempt to open, disassemble, modify or service the battery pack.
Refer to
instructions
Indoor use only
CP20VMCEU Issue 1 09/01/2025
Original Language Version
© Jack Sealey Limited
8 DO NOT crush, puncture, short external contacts or dispose of in re or water.
8 DO NOT expose to temperatures above 40°C (104°F).
9 Use only the charging base to charge the CP20V series batteries.
WARNING! Dispose of spent batteries correctly as they contain Lithium-ion. DANGER! DO NOT attempt to disassemble the battery.
8 For safety and environmental reasons DO NOT discard in domestic waste or by burning.
9 ONLY discard or recycle according to local authority regulations.
WARNING! DO NOT allow a leaking battery to contact your person.
2. INTRODUCTION
Mains charger for SV20 power tool batteries - Model No’s CP20VBP2, CP20VBP4, CP20VBP6. LED indicates status of battery from
charging to full. Suitable for use with the SV20 Series.
3. SPECIFICATION
Model No: ................................................. CP20VMCEU
Application(s): ............................................... CP20VBP2
........................................................................CP20VBP
......................................................................CP20VBP4
......................................................................CP20VBP6
Fuse Rating:................................................................3A
Nett Weight: ......................................................... 0.37kg
Output: ........................................................................3A
Plug Type: ........................................................... Schuko
Power Supply Cable Length: ...................................1.8m
Supply: ......................................................... 230V~50Hz
4. OPERATION
NOTE: when new, the batteries will have been shipped in a low charge state. Fully charge the batteries before using your tool.
4.1. To remove the battery from the equipment, depress the spring loaded button on the battery pack. Remove the battery pack by sliding
out. DO NOT touch the metal battery terminals.
4.2. The battery is designed to t into the charger one way only. Insert the battery fully and rmly to seat the battery into the charging base.
4.3. Take the base charger and plug it into the mains, switch on the power and the LED on the charger will illuminate.
4.4. When the battery is on charge the red LED on the charger will illuminate.
4.5. When the green LED on the Charger illuminates permanently the battery is fully charged.
4.6. Remove the battery from the charger. Switch o and remove the plug from the mains.
5. MAINTENANCE
8 DO NOT attempt to open, disassemble, modify or service the battery charger.
9 Store the battery charger in a clean, dry place, away from direct sunlight and high/low temperatures.
9 Clean with a soft, dry cloth. DO NOT use harsh chemicals or abrasives as this may damage the battery charger.
6. DISPOSAL
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment
(WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid
waste authority for recycling information.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 sales@sealey.co.uk www.sealey.co.uk
WEEE REGULATIONS
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic
Equipment (WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact
your local solid waste authority for recycling information.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specications and component parts without prior notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be
sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When
the product becomes completely unserviceable and requires disposal, drain any uids (if applicable) into approved
containers and dispose of the product and uids according to local regulations.
REGISTER YOUR
PURCHASE HERE
CP20VMCEU Issue 1 09/01/2025
Original Language Version
© Jack Sealey Limited
