Form No. 3460-234 Rev A
Flex-Force Power System
™
41cm
(16in) 60V MAX Chainsaw
Model No. 51851 —Serial No. 323000001 and Up
Register at www .T oro.com.
Original Instructions (EN)
*3460-234*
For assistance, please see
www .T oro.com/support
for instructional videos
or contact 1-888-384-9939
before returning this
product.
W ARNING
CALIFORNIA
Proposition 65 W arning
The power cord on this product contains
lead, a chemical known to the State
of California to cause birth defects
or other reproductive harm. W ash
hands after handling.
Use of this product may cause exposure
to chemicals known to the State of
California to cause cancer , birth defects,
or other reproductive harm.
Introduction
his chain saw is designed for cutting tree branches,
logs, and wooden beams of a diameter no longer than
the cutting length of the guide bar . It is to be used only
by adults. It is designed to use T oro 60V lithium-ion
battery packs. These battery packs are designed
to be charged only by T oro 60V lithium-ion battery
chargers. Using these products for purposes other
than their intended use could prove dangerous to you
and bystanders. Using these products for purposes
other than their intended use could prove dangerous
to you and bystanders.
Read this information carefully to learn how to operate
and maintain your product properly and to avoid
injury and product damage. Y ou are responsible for
operating the product properly and safely .
V isit www .T oro.com for more information, including
safety tips, training materials, accessory information,
help nding a dealer , or to register your product.
Whenever you need service, genuine T oro parts, or
additional information, contact an Authorized Service
Dealer or T oro Customer Service and have the model
and serial numbers of your product ready . Figure 1
identies the location of the model and serial numbers
on the product. W rite the numbers in the space
provided.
Important: W ith your mobile device, you can
scan the QR code (if equipped) on the serial
number plate to access warranty , parts, and other
product information.
g425184
Figure 1
1. Model and serial number location.
Model No.
Serial No.
© 2023—The T oro® Company
81 1 1 L yndale A venue South
Bloomington, MN 55420
2
Contact us at www .T oro.com.
Printed in China
All Rights Reserved
Safety-Alert Symbol
The safety-alert symbol ( Figure 2 ) shown in this
manual and on the machine identies important safety
messages that you must follow to prevent accidents.
g000502
Figure 2
Safety-alert symbol
The safety-alert symbol appears above information
that alerts you to unsafe actions or situations and
is followed by the word DANGER , W ARNING , or
CAUTION .
DANGER indicates an imminently hazardous situation
which, if not avoided, will result in death or serious
injury .
W ARNING indicates a potentially hazardous situation
which, if not avoided, could result in death or serious
injury .
CAUTION indicates a potentially hazardous situation
which, if not avoided, may result in minor or moderate
injury .
This manual uses two other words to highlight
information. Important calls attention to special
mechanical information and Note emphasizes general
information worthy of special attention.
Contents
Safety-Alert Symbol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Personal Protective Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Safety and Instructional Decals . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Filling the Chain Saw with Bar and Chain
Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Specications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1
Attachments/Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1
Before Using the Chain Saw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1
Starting the Chain Saw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Shutting Of f the Chain Saw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Cutting with the Chain Saw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Pruning a T ree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Felling a T ree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Limbing a Fallen T ree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Bucking a Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Installing the Battery Pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Removing the Battery Pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Charging the Battery Pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Recommended Maintenance Schedule(s) . . . . . . . . . . . 20
Checking the Oil Level and Adding Bar and
Chain Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Checking the Chain Brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Checking the Flow of Bar and Chain
Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Adjusting the Chain T ension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Servicing the Guide Bar , Chain, and Drive
Sprocket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Installing the Guide Bar and Chain . . . . . . . . . . . . . . . . . . . . 24
Sharpening the Chain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Preparing the Battery Pack for
Recycling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
T roubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
3
Safety
W ARNING
Read all safety warnings, instructions,
illustrations and specications provided with
this power tool.
Failure to follow all instructions listed below
may result in electric shock, re and/or
serious injury .
Save all warnings and instructions for future
reference.
The term “power tool” in all the warnings refers
to your mains-operated (corded) power tool or
battery-operated (cordless) power tool.
IMPORT ANT SAFETY
INSTRUCTIONS
I. W ork area safety
1. Keep work area clean and well lit. Cluttered
or dark areas invite accidents.
2. Do not operate power tools in explosive
atmospheres, such as in the presence of
ammable liquids, gases, or dust. Power
tools create sparks which may ignite the dust
or fumes.
3. Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
II. Electrical safety
1. Power tool plugs must match the outlet.
Never modify the plug in any way . Do not use
any adapter plugs with earthed (grounded)
power tools. Unmodied plugs and matching
outlets will reduce risk of electric shock.
2. A void body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges
and refrigerators. There is an increased risk
of electric shock if your body is earthed or
grounded.
3. Do not expose power tools to rain or wet
conditions. W ater entering a power tool will
increase the risk of electric shock.
4. Do not abuse the cord. Never use the cord
for carrying, pulling or unplugging the power
tool. Keep cord away from heat, oil, sharp
edges or moving parts. Damaged or entangled
cords increase the risk of electric shock.
5. When operating a power tool outdoors, use
an extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces
the risk of electric shock.
6. If operating a power tool in a damp location
is unavoidable, use a residual current device
(RCD) protected supply . Use of an RCD
reduces the risk of electric shock.
III. Personal safety
1. Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired
or under the inuence of drugs, alcohol, or
medication. A moment of inattention while
operating power tools may result in serious
personal injury .
2. Use personal protective equipment. Always
wear eye protection. Protective equipment
such as dust mask, non-skid safety shoes, hard
hat, or hearing protection used for appropriate
conditions reduces personal injuries.
3. Prevent unintentional starting. Ensure
the switch is in the O FF -position before
connecting to power source and/or battery
pack, picking up or carrying the tool. Carrying
power tools with your nger on the switch or
energizing power tools that have the switch on
invites accidents.
4. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key
left attached to a rotating part of the power tool
may result in personal injury .
5. Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
6. Dress properly . Do not wear loose clothing
or jewelry . Keep your hair and clothing away
from moving parts. Loose clothes, jewelry , or
long hair can be caught in moving parts.
7. If devices are provided for the connection
of dust extraction and collection facilities,
ensure these are connected and properly
used. Use of dust collection can reduce
dust-related hazards.
8. Do not let familiarity gained from frequent
use of tools allow you to become complacent
and ignore tool safety principles. A careless
action can cause severe injury within a fraction
of a second.
4
IV . Power tool use and care
1. Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the
rate for which it was designed.
2. Do not use the power tool if the switch
does not turn it on and off. Any power tool
that cannot be controlled with the switch is
dangerous and must be repaired.
3. Disconnect the plug from the power source
and/or remove the battery pack, if detachable,
from the power tool before making any
adjustments, changing accessories, or
storing power tools. Such preventive safety
measures reduce the risk of starting the power
tool accidentally .
4. Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions
to operate the power tool. Power tools are
dangerous in the hands of untrained users.
5. Maintain power tools and accessories.
Check for misalignment or binding of moving
parts, breakage of parts, and any other
condition that may affect the power tool’ s
operation. If damaged, have the power tool
repaired before use. Many accidents are
caused by poorly maintained power tools.
6. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
7. Use the power tool, accessories, and tool bits
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed. Use of the
power tool for operations different from those
intended could result in a hazardous situation.
8. Keep handles and grasping surfaces dry ,
clean and free from oil and grease. Slippery
handles and grasping surfaces do not allow
for safe handling and control of the tool in
unexpected situations.
V . Battery tool use and care
1. Recharge only with the charger specied by
the manufacturer . A charger that is suitable for
one type of battery pack may create a risk of re
when used with another battery pack.
2. Use power tools only with specically
designated battery packs. Use of any other
battery packs may create a risk of injury and re.
3. When battery pack is not in use, keep it away
from other metal objects, like paper clips,
coins, keys, nails, screws or other small
metal objects, that can make a connection
from one terminal to another . Shorting the
battery terminals together may cause burns or
a re.
4. Under abusive conditions, liquid may be
ejected from the battery; avoid contact. If
contact accidentally occurs, ush with water .
If liquid contacts eyes, additionally seek
medical help. Liquid ejected from the battery
may cause irritation or burns.
5. Do not use a battery pack or tool that is
damaged or modied. Damaged or modied
batteries may exhibit unpredictable behavior
resulting in re, explosion or risk of injury .
6. Do not expose a battery pack or tool to re
or excessive temperature. Exposure to re or
temperature above 130 °C (265 °F) may cause
explosion.
7. Follow all charging instructions and do
not charge the battery pack or tool outside
the temperature range specied in the
instructions. Charging improperly or at
temperatures outside the specied range may
damage the battery and increase the risk of re.
VI. Service
1. Have your power tool serviced by a
qualied repair person using only identical
replacement parts. This will ensure that the
safety of the power tool is maintained.
2. Never service damaged battery packs.
Service of battery packs should only be
performed by the manufacturer or authorized
service providers.
5
VII. Chain saw safety
1. Keep all parts of the body away from the
saw chain when the chain saw is operating.
Before you start the chain saw , make sure
the saw chain is not contacting anything.
A moment of inattention while operating chain
saws may cause entanglement of your clothing
or body with the saw chain.
2. Always hold the chain saw with your right
hand on the rear handle and your left hand
on the front handle. Holding the chain saw with
a reversed hand conguration increases the risk
of personal injury and should never be done.
3. Hold the chain saw by insulated gripping
surfaces only , because the saw chain may
contact hidden wiring. Saw chains contacting
a "live" wire may make exposed metal parts of
the chain saw "live'" and could give the operator
an electric shock.
4. W ear eye protection. Further protective
equipment for hearing, head, hands, legs and
feet is recommended. Adequate protective
equipment will reduce personal injury from ying
debris or accidental contact with the saw chain.
5. Do not operate a chain saw in a tree, on
a ladder , from a rooftop, or any unstable
support. Operation of a chain saw in this
manner could result in serious personal injury .
6. Always keep proper footing and operate
the chain saw only when standing on xed,
secure and level surface. Slippery or unstable
surfaces such as ladders may cause a loss of
balance or control of the chain saw .
7. When cutting a limb that is under tension, be
alert for spring back. When the tension in the
wood bers is released, the spring loaded limb
may strike the operator and/or throw the chain
saw out of control.
8. Use extreme caution when cutting brush and
saplings. The slender material may catch the
saw chain and be whipped toward you or pull
you off balance.
9. Carry the chain saw by the front handle with
the chain saw switched off and away from
your body . When transporting or storing the
chain saw , always t the guide bar cover and
remove the battery . Proper handling of the
chain saw will reduce the likelihood of accidental
contact with the moving saw chain.
10. Follow instructions for lubricating, chain
tensioning, and changing the bar and chain.
Improperly tensioned or lubricated chain may
either break or increase the chance for kickback.
1 1. Cut wood only . Do not use chain saw for
purposes not intended. For example: do
not use chain saw for cutting metal, plastic,
masonry or non-wood building materials.
Use of the chain saw for operations different than
intended could result in a hazardous situation.
12. Do not attempt to fell a tree until you have an
understanding of the risks and how to avoid
them. Serious injury could occur to the operator
or bystanders while felling a tree.
13. Follow all instructions when clearing jammed
material, storing or servicing the chain saw .
Make sure the switch is off and the battery
pack is removed. Unexpected actuation of
the machine while clearing jammed material or
servicing may result in serious personal injury .
6
14. Causes and operator prevention of kickback.
Kickback may occur when the nose or tip of the
guide bar touches an object, or when the wood
closes in and pinches the saw chain in the cut.
T ip contact in some cases may cause a sudden
reverse reaction, kicking the guide bar up and
back towards the operator .
Pinching the saw chain along the top of the
guide bar may push the guide bar rapidly back
towards the operator .
Either of these reactions may cause you to lose
control of the saw , which could result in serious
personal injury . Do not rely exclusively upon the
safety devices built into your saw . As a chain
saw user , you should take several steps to keep
your cutting jobs free from accident or injury .
Kickback is the result of chain saw misuse and/or
incorrect operating procedures or conditions and
can be avoided by taking proper precautions as
given below:
A. Maintain a rm grip, with thumbs and
ngers encircling the chain saw handles,
with both hands on the saw and position
your body and arm to allow you to resist
kickback forces. Kickback forces can
be controlled by the operator , if proper
precautions are taken. Do not let go of the
chain saw .
B. Do not overreach and do not cut above
shoulder height. This helps prevent
unintended tip contact and enables better
control of the chain saw in unexpected
situations.
C. Only use replacement guide bars
and saw chains specied by the
manufacturer . Incorrect replacement guide
bars and saw chains may cause chain
breakage and/or kickback.
D. Follow the manufacturer ’ s sharpening
and maintenance instructions for the
saw chain. Decreasing the depth gauge
height can lead to increased kickback.
SA VE THESE
INSTRUCTIONS
Personal Protective
Equipment
g316566
Figure 3
1. W ear a hard hat in
situations where debris
may contact the head.
4. W ear gloves
2. W ear hearing protection 5. W ear protective pants or
chaps
3. W ear safety glasses
and/or a face shield
6. W ear substantial,
slip-resistant footwear
7
Safety and Instructional Decals
Safety decals and instructions are easily visible to the operator and are located near any area
of potential danger . Replace any decal that is damaged or missing.
decal144-3094
144-3094
1. The battery pack is
charging.
3. The battery pack is over
or under the appropriate
temperature range.
2. The battery pack is fully
charged.
4. Battery pack charging fault
decal144-3098
144-3098
decal144-3096
144-3096
decal144-3090
144-3090
decal145-8271
145-8271
8
decal140-8475
140-8475
1. Read the Operator ’ s
Manual .
3. Keep away from open re
or ames.
2. Call2Recycle® battery
recycling program
4. Do not expose to rain.
decal137-9461
137-9461
1. Battery charge status
decal145-8273
145-8273
1. Cutting hazard of hand.
7. Do no expose to rain.
2. Stay away from moving parts. 8. Read the Operator ’ s Manual .
3. Keep all guards and shields in place. 9. W ear hearing protection.
4. Kickback hazard 10. W ear eye protection.
5. Do not contact objects with the guide bar tip. 1 1. Always use 2 hands when operating the chain saw .
6. Do not operate the chain saw holding it with one hand only .
9
Setup
Important: The battery pack is not fully charged
when it is purchased. Before using the machine
for the rst time, refer to Charging the Battery
Pack ( page 19 ) .
Filling the Chain Saw with
Bar and Chain Oil
Important: Use only bar and chain oil (sold
separately).
Fill the chain saw with bar and chain oil; refer to
Checking the Oil Level and Adding Bar and Chain
Oil ( page 20 ) .
Product Overview
g315699
Figure 4
Left side shown
1. Chain
6. Battery pack
2. Guide bar
7. Button latch
3. Oil window
8. T rigger lock
4. Oil cap
9. T rigger
5. Front handle 10. Bucking teeth
g315700
Figure 5
Right side shown
1. Chain brake 4. Multitool (located beneath
rear handle)
2. Side cover 5. Chain tensioning screw
3. Captive cover nut 6. Guide bar cover
g330065
Figure 6
1. Battery charger Model
88610 (included with
Model 51851)
2. Battery pack Model 88620
(included with Model
51851)
10
Specications
Model
51851/51851T
Bar Length (with 88613 and
88614 equipped)
40.6 cm (16 inches)
Chain Gauge (with 88613
and 88614 equipped)
0.043 inches
Chain Pitch (with 88613 and
88614 equipped)
3/8 inch
Chain Length (with 88613
and 88614 equipped)
56 links
Rated V oltage
60V DC maximum, 54 VDC
nominal usage
W eight (without a battery) 4.35 kg (9.59 lb)
Charger T ype
T oro 60V lithium-ion chargers
Battery T ype T oro 60V lithum-ion batteries
Appropriate T emperature Ranges
Charge/store the battery pack
at
5°C (41°F) to 40°C (104°F)*
Use the battery pack at
-30°C (-22°F) to 49°C (120°F)*
Use the tool at
0°C (32°F) to 49°C (120°F)*
*Charging time will increase if you do not charge the
battery within this range.
Store the tool, battery pack, and battery charger in an
enclosed clean, dry area.
Attachments/Accessories
A selection of T oro approved attachments and
accessories is available for use with the machine
to enhance and expand its capabilities. Contact
your Authorized Service Dealer or authorized T oro
distributor or go to www .T oro.com for a list of all
approved attachments and accessories.
T o ensure optimum performance and continued safety
certication of the machine, use only genuine T oro
replacement parts and accessories. Replacement
parts and accessories made by other manufacturers
could be dangerous.
Operation
Before Using the Chain Saw
Before using the chain saw , do the following:
• Check the chain tension; refer to Adjusting the
Chain T ension ( page 22 ) .
• Clean the chain saw components, inspect them for
excessive wear or damage, and replace them as
needed; refer to Servicing the Guide Bar , Chain,
and Drive Sprocket ( page 23 ) .
• Check the chain for sharpness and damage, and
sharpen or replace as needed; refer to Sharpening
the Chain ( page 24 ) .
• Check the oil level; refer to Checking the Oil Level
and Adding Bar and Chain Oil ( page 20 ) .
• Check the chain brake; refer to Checking the
Chain Brake ( page 21 ) .
• Check the chain saw for damage, general
appearance, and performance; ensure that the
switches move freely , the vents and handles are
clean, and the bar is not bent or damaged.
1 1
Starting the Chain Saw
1. Ensure that the vents on the chain saw are free
from dust and debris ( Figure 7 ).
g315701
Figure 7
1. Side vent
2. Bottom vent
2. Set the chain saw down on a level surface.
3. Align the tongue of the battery pack with the
battery cavity in the chain saw ( Figure 8 ).
g315702
Figure 8
4. Push the battery pack into the battery cavity until
the battery pack locks into place.
5. Remove the protective cover from the chain.
6. Ensure that the chain brake is in the O PERATING
position ( Figure 9 ).
g315703
Figure 9
1. Chain brake ( O PERATING
position)
2. Chain brake ( STOP
position)
7. With your left hand on the front handle and your
right hand on the rear handle, press the trigger
lock, then squeeze the trigger ( Figure 10 ).
g315704
Figure 10
1. Front handle 4. T rigger
2. Chain brake
5. Rear handle
3. T rigger lock
Shutting Off the Chain Saw
T o shut of f the chain saw , release the trigger .
Whenever you are not using the saw or are
transporting the saw to or from the work area, move
the chain brake to the S TOP position ( Figure 9 ) and
remove the battery pack.
12
Cutting with the Chain Saw
W ARNING
Operating a chain saw improperly can cause
serious personal injury or death.
Read and follow all operating instructions
carefully to avoid possible personal injury .
W ARNING
Kickback can cause serious or fatal injury to
you.
Always ensure that the chain brake system
is working properly before you operate the
chain saw .
A void touching objects to be cut with the
nose of the chain saw guide bar .
There are 2 types of kickback:
• A fast upward motion of the chain saw that results
when the chain at the nose or top of the bar
contacts an object
• A fast backward motion of the chain saw that
results when the chain at the nose or top of the bar
is pinched by the object being cut
Figure 1 1 shows the area of the bar to avoid contacting
an object to prevent kickback.
g318677
Figure 1 1
1. Kickback area (nose, top
of the bar)
2. Nose
1. Grip the chain saw with 2 hands, with your left
hand on the front handle and your right hand on
the rear handle as shown in Figure 12 .
Important: Keep your left arm straight with
your elbow locked to help reduce kickback.
g025213
Figure 12
2. Stand on solid, even ground in front of the wood
to be cut.
3. Stand to the left side of the chain saw , not in
line with the chain , and position yourself for
balanced, stable footing while cutting.
Important: Do not stand on the wood that
you are cutting.
4. Ensure that you only cut the wood that you
intend to cut; do not allow the saw chain to
contact the earth, other logs, or any other
objects when cutting.
5. Ensure that the saw chain is rotating at full
speed before starting a cut.
6. Cut with the wood near the rear of the guide bar ,
close to the bucking teeth; press the chain saw
lightly against the wood and allow the weight of
the chain saw to drive the cutting.
Note: Y ou can use the bucking teeth ( Figure
13 ) to apply light pressure.
g315747
Figure 13
1. Bucking teeth
7. Keep steady pressure on the chain saw , cutting
in a straight line, and release pressure only near
the end of the cut.
13
Pruning a T ree
W ARNING
Cutting higher limbs from a tree off the ground
can put you in an unstable position that could
be unsafe for you while handling a chain saw ,
resulting in possible serious personal injury
or death to you or bystanders.
When cutting limbs from a standing tree, use
the following practices:
• Do not climb on limbs or branches with a
chain saw .
• Do not overreach, and cut with both hands
on the chain saw .
• Ensure that all bystanders are away from
the area where branches may fall.
1. Grip the chain saw as shown in Figure 12 .
2. While cutting small branches, apply light
pressure to the branch to be cut.
3. While cutting larger branches, make a shallow
undercut and then complete the cut from the
topside of the branch.
A. Cut from the underside of the limb about 15
cm (6 inches) from the trunk. Cut a third of
the way through the limb.
B. Cut 5.0 to 10.0 cm (2 to 4 inches) farther
out on the limb and from above. Cut the
limb until it falls.
C. Cut the limb stub at the branch collar
( Figure 14 ).
Important: Do not cut the limb past the
collar , ush to the trunk, or leave a large
limb stub; this damages the tree.
g316577
Figure 14
1. First relief undercut
3. Final pruning cut to
remove the limb stub
2. Second through cut 4. Branch collar (where the
trunk transitions to the
limb)
Felling a T ree
W ARNING
Cutting standing trees requires expertise and
poses hazards.
• Before attempting to cut a big tree, practice
cutting a few branches, limbs, or small logs
to familiarize yourself with the chain saw .
• Do not use this chain saw to fell large trees
with a diameter larger than the length of
the guide bar .
DANGER
Loose or tangled limbs above you may be
dislodged by vibration from cutting, causing
severe injury or death.
Always look overhead for loose and tangled
limbs before cutting; if you see any loose
limbs or branches, remove them before
cutting.
The proper operator stance for felling a tree is shown
in Figure 15 .
14
g195831
Figure 15
1. Determine the direction that the tree will fall.
T ake the following variables into consideration:
• Wind direction
• Heavier limbs on 1 side of the tree
• Natural tilt of the tree (if any)
2. Determine a clear , safe retreat path away from
the danger area; refer to Figure 16 .
g024800
Figure 16
1. Retreat path (at a 45°
angle opposite from the
planned direction of fall)
3. Danger area
2. Planned direction of fall
3. Grip the chain saw as shown in ( Figure 12 ).
4. Make the rst cut a third of the way through the
tree diameter on the side where you want the
tree to fall ( Figure 17 ).
Note: Making this cut prevents the chain saw
from being pinched while making the next cut.
g228707
Figure 17
1. First cut 3. Hinge
2. Second cut
4. Back cut
5. Make a second cut to form a notch, starting the
cut at least 5 cm (2 inches) above and away
from the rst cut ( Figure 17 ).
Important: Ensure that the rst cut and the
second cut meet at the same point, forming
a clean notch.
6. Make the back cut from the opposite side of the
notch and about 5 cm (2 inches) higher than the
bottom of the notch as shown in Figure 17 .
Important: Stop the third cut 2.5 to 5.0 cm
(1 to 2 inches) from the notch to form a hinge
between the cuts ( Figure 17 ), which keeps
the tree from falling in the wrong direction
or twisting as it falls.
Note: As the back cut nears the hinge ( Figure
17 ), the tree should begin to fall.
7. When the tree begins to fall, remove the chain
saw , shut it of f, put it down, and retreat along the
path you determined in step 2 .
Important: If the tree begins to fall in an
undesired direction, immediately stop the
cut, shut off the chain saw , put the chain saw
down, and use a non-metallic wedge to open
the back cut and push the tree in the desired
direction.
15
Limbing a Fallen T ree
1. Grip the chain saw as shown in Figure 12 .
2. Moving from the base of the tree up, cut of f the smaller limbs from the tree that are not supporting its
weight of f the ground ( Figure 18 ).
3. Cut the larger limbs that support the weight of the tree from the bottom upward so that the limbs do
not pinch the saw blade ( Figure 19 ).
g316601
Figure 18
g315751
Figure 19
16
Bucking a Log
When bucking a log, note where the log is supported
and where there is a load on the log. Cut the log so
that when the ends fall, your guide bar will not be
pinched between them.
Important: If the chain saw binds in the cut, do
not attempt to free it by running the motor . Shut
off the saw , remove the battery , then use a wedge
to pry open the cut and release the saw .
If you are cutting branches from a fallen tree or cutting
a log into lengths, support the log of f the ground
(preferably on a sawbuck).
• If the log is supported on both ends, but not in the
middle, the load is on the center of the log.
– Start from the top and cut about a third of the
way through the log ( Figure 20 A).
– Make a second cut from the underside to meet
the rst cut ( Figure 20 B). This keeps the log
from pinching the saw .
g315765
Figure 20
• If the log is supported on a single end, the load is
on the free end of the log.
– Start from the underside and cut about a third
of the way through the log.
– Make a second cut from the top to meet the rst
cut. This keeps the log from pinching the saw .
• If the log is supported of f the ground along its entire
length, without a heavy load on the log at any
point, cut all the way through the log from the top.
• If the log is on a hill, always stand on the uphill
side of the log ( Figure 21 ).
g315767
Figure 21
1. Direction of slope
• If the whole length of the log is supported on at,
level ground, cut a third of the diameter from the
top, then roll the log over and make another cut to
meet the rst cut ( Figure 22 ).
g315766
Figure 22
17
Installing the Battery Pack
Important: Use the battery pack only in
temperatures that are within the appropriate
range; refer to Specications ( page 1 1 ) .
1. Set the chain saw down on a level surface.
2. Align the tongue of the battery pack with the
battery cavity in the chain saw ( Figure 23 ).
g315702
Figure 23
3. Push the battery pack into the battery cavity until
the battery pack locks into place.
Removing the Battery Pack
1. Place the chain saw on a at surface.
2. Press down on the latch and remove the battery
pack from the cavity .
g315763
Figure 24
1. Latch
18
Charging the Battery Pack
Important: The battery pack is not fully charged
when you purchase it. Before using the tool for
the rst time, place the battery pack in the charger
and charge it until the LED display indicates the
battery pack is fully charged. Read all safety
precautions.
Important: Charge the battery pack only in
temperatures that are within the appropriate
range; refer to Specications ( page 1 1 ) .
Note: At any time, press the battery-charge-indicator
button on the battery pack to display the current
charge (LED indicators).
1. Ensure that the vents on the battery and charger
are clear of any dust and debris.
g330066
Figure 25
1. Battery pack cavity
5. LED indicators (current
charge)
2. Battery pack venting areas 6. Handle
3. Battery pack terminals
7. Charger
4. Battery-charge-indicator
button
2. Line up the charger with the cavity on the back
of the battery pack ( Figure 25 ).
3. Slide the charger into the battery pack until it is
fully seated ( Figure 25 ).
4. T o remove the charger , slide the charger
backward out of the battery .
5. Refer to the following table to interpret the LED
indicator light on the battery charger .
Indicator
light
Indicates
Of f
No battery pack inserted
Green
blinking
Battery pack is charging
Green
Battery pack is charged
Red
Battery pack and/or battery charger is over or under
the appropriate temperature range
Red
blinking
Battery pack charging fault*
*Refer to T roubleshooting ( page 26 ) for more
information.
Important: The battery can be left on the charger
for short periods between uses.
If the battery will not be used for longer periods,
remove the battery from the charger; refer to
Storage ( page 25 ) .
19
Maintenance
Recommended Maintenance Schedule(s)
Maintenance Service
Interval
Maintenance Procedure
Before each use or daily
• Check the oil level and add bar and chain oil if necessary .
• Check the chain brake.
• Check that oil is owing to the chain.
• Check the chain tension and adjust it if necessary .
• Ensure that the bar is straight and undamaged
• Check the chain for sharpness; contact an Authorized Service Dealer to have the
chain sharpened or replaced.
After each battery drain
cycle
• Check the oil level and add bar and chain oil if necessary .
• Check the chain brake.
• Check the chain tension and adjust it if necessary .
Y early or before storage
• Service the guide bar , chain, and drive sprocket.
• Check the chain for sharpness; contact an Authorized Service Dealer to have the
chain sharpened or replaced.
Checking the Oil Level and
Adding Bar and Chain Oil
Service Interval : Before each use or daily
After each battery drain cycle
Important: Use only bar and chain oil (sold
separately).
1. Shut of f the chain saw and remove the battery
pack; refer to Removing the Battery Pack ( page
18 ) .
2. Check the oil level in the window . If the oil does
not ll the window , add bar and chain oil as
needed ( Figure 26 ).
g315841
Figure 26
1. Oil window 2. Oil cap
3. Place the chain saw on a at surface with the
oil cap facing up.
4. Clean the area around the oil cap ( Figure 26 ).
Note: Ensure that you do not allow debris/wood
chips to enter the oil tank.
5. Unfold the wing-nut tab on the oil cap tab,
remove the cap, and pour bar and chain oil into
the chain saw until the oil lls the tank ( Figure
26 ).
Important: Do not ll the chain saw higher
than the bottom of the ll neck.
6. Clean up any spilled oil, secure the oil cap, and
fold the wing-nut tab down.
7. Ensure that oil is owing to the chain; refer to
Checking the Flow of Bar and Chain Oil ( page
21 ) .
20
Checking the Chain Brake
Service Interval : Before each use or daily
After each battery drain cycle
1. Engage the chain brake by moving the chain
brake forward to the STOP position ( Figure 27 ).
g315840
Figure 27
1. Chain brake ( O PERATING
position)
2. Chain brake ( STOP
position)
2. Prepare to test the chain saw operation; refer to
Before Using the Chain Saw ( page 1 1 ) .
3. Attempt to start the chain saw . If it starts, take
the chain saw to an Authorized Service Dealer
for repair .
4. Disengage the chain brake by moving the
chain brake rearward to the O PERATING position
( Figure 27 ).
Checking the Flow of Bar
and Chain Oil
Service Interval : Before each use or daily
1. Prepare to use the chain saw; refer to Before
Using the Chain Saw ( page 1 1 ) .
2. T o ensure that oil is owing to the chain, point
the nose of the chain saw a few inches from a
surface (e.g. paper , cardboard, a stump) and
run the chain saw; you should be able to see a
light spray of oil on the surface ( Figure 28 ).
g317663
Figure 28
1. Run the chain saw a few
inches from a surface.
2. If the oil is owing, it will
spray of f the chain and
accumulate.
3. If oil is not owing, ensure that there is oil in the
tank and that the area under the side cover is
clean; refer to Checking the Oil Level and Adding
Bar and Chain Oil ( page 20 ) and Servicing the
Guide Bar , Chain, and Drive Sprocket ( page 23 ) .
21
Adjusting the Chain
T ension
Service Interval : Before each use or daily
After each battery drain cycle
Ensure that the chain is properly tensioned.
A loose chain shortens the life of the drive sprocket
and the guide bar and may cause the chain to fall of f.
An overtightened chain overheats the guide bar and
chain, causing rapid wear , and may burn out the motor
or break the chain.
The chain tension is correct when you are able to use
a gloved hand to pull the chain smoothly around the
guide bar . The chain should remain in contact with
the bottom edge of the guide bar .
Also, check the chain tension of a new chain after a
few cuts; a new chain usually stretches and requires
adjustment after a few cuts.
DANGER
Contact with the chain saw teeth can cause
serious personal injury .
• Remove the battery pack before adjusting
or maintaining the chain saw .
• Always wear gloves when adjusting or
maintaining the chain saw .
1. Place the chain saw on a level surface and
remove the battery pack; refer to Removing the
Battery Pack ( page 18 ) .
2. Allow the saw chain to cool.
Important: Do not tension a hot chain; it
may contract as it cools, resulting in an
overtightened chain.
3. Inspect the guide bar for bends or damage,
replace if necessary .
4. Ensure that the chain brake is in the O PERATING
position ( Figure 27 ).
5. Using the onboard multitool, loosen the captive
nuts on the side cover , but do not remove it
( Figure 30 ).
6. Hold up the tip of the guide bar ( Figure 29 ).
g315842
Figure 29
7. Using the onboard multitool, adjust the chain
tension, and then secure the side cover to the
chain saw by tightening the captive nuts ( Figure
30 ).
• T o tighten the chain, turn the chain
tensioning screw clockwise ( Figure 29 ).
• T o loosen the chain, turn the chain
tensioning screw counterclockwise
Adjust the chain tension until the chain touches
the bottom edge of the guide bar , then pull the
chain away from the bottom edge of the guide
bar; a properly adjusted chain can only be pulled
3.2 to 6.4 mm (1/8 to 1/4 inch) away from the
guide bar , and snaps back on release.
If the chain is not properly tensioned, loosen the
side cover and repeat steps 5 through 7 .
8. Use a gloved hand to pull the chain around the
guide bar . A properly tensioned chain should
move smoothly and remain in contact with the
bottom edge of the guide bar .
9. Check the chain tension again and repeat this
procedure if necessary .
22
Servicing the Guide Bar ,
Chain, and Drive Sprocket
Y early or before storage
DANGER
Contact with the chain saw teeth can cause
serious personal injury .
• Remove the battery pack before adjusting
or maintaining the chain saw .
• Always wear gloves when adjusting or
maintaining the chain saw .
1. Place the chain saw on a at surface and
remove the battery pack; refer to Removing the
Battery Pack ( page 18 ) .
2. Remove the side cover by loosening the 2
captive nuts that secure the cover ( Figure 30 ).
Note: The captive nuts do not separate from
the side cover; loosen them until the cover can
be removed.
g315844
Figure 30
1. Cover 3. Chain tensioning screw
2. Captive nut
4. Multitool
3. Loosen the chain by turning the chain-tightening
screw counterclockwise ( Figure 30 ).
4. Separate the chain from the guide bar and set
them aside.
5. Remove the clip and drive sprocket from the
chain saw ( Figure 31 ).
6. Clean any debris from the area under the side
cover .
7. Inspect the drive sprocket; if it is excessively
worn or damaged, replace it.
8. Install the drive sprocket and clip.
9. Check the oil outlet ( Figure 31 ) for debris and
clean the area if necessary .
g315855
Figure 31
1. Drive sprocket
3. Oil outlet
2. Clip
10. Clean the guide bar and chain; use a wire or a
small at-head screwdriver to remove dirt and
debris from the groove along the edge of the
guide bar , starting from the sprocket on the front
end and moving rearward.
Ensure that the oil channel in the bar that aligns
with the oil outlet on the chain saw is clean so
that oil can ow freely to the chain ( Figure 32 ).
g315856
Figure 32
Internal sections of the guide bar shown
1. Ensure that this channel
connecting to the oil outlet
is clean.
2. Ensure that the bar
sprocket is clean and
rotates freely .
1 1. Inspect the guide bar and chain; if the bar
is bent, the grooves are damaged, or if the
sprocket on the front end does not rotate freely ,
replace the guide bar; if the chain is excessively
worn or damaged, replace it.
12. Install the guide bar and chain; refer to Installing
the Guide Bar and Chain ( page 24 ) .
13. Ensure that oil is owing to the chain; refer to
Checking the Flow of Bar and Chain Oil ( page
21 ) .
23
Installing the Guide Bar and
Chain
DANGER
Contact with the chain saw teeth can cause
serious personal injury .
• Remove the battery pack before adjusting
or maintaining the chain saw .
• Always wear gloves when adjusting or
maintaining the chain saw .
1. If the side cover is installed to the machine,
loosen the 2 captive nuts securing the side cover
to the machine and remove it ( Figure 33 A and
Figure 33 B).
2. Place the chain around the drive sprocket on
the front end of the guide bar , with the cutting
edge of the chain teeth on the top of the bar
facing forward as shown in the diagram on the
side cover of the chain saw ( Figure 33 C).
g315857
Figure 33
3. Feed the chain around the guide bar and align
the chain into the groove of the guide bar .
Note: If you are installing a new chain, ip the
guide bar to avoid uneven wear .
4. Position the open loop of the chain (not on the
guide bar) around the drive sprocket on the
chain saw and install the guide bar and attached
chain onto the chain saw as shown in Figure
33 C.
Important: Ensure that the chain adjusting
stud is inserted into the hole indicated by the
arrow in Figure 33 C. Y ou may need to rotate
the chain tensioning knob to t the stud into
the hole in the guide bar .
5. Install the side cover , but do not fully tighten the
captive nuts ( Figure 33 D).
6. Adjust the chain tension; refer to Adjusting the
Chain T ension ( page 22 ) .
Sharpening the Chain
Y early or before storage
A sharp chain ensures better cutting performance and
longer battery life.
The chain needs to be sharpened or replaced if you
must force it onto the wood, or if it produces sawdust
instead of full wood chips.
Contact an Authorized Service Dealer to have the
chain sharpened or replaced.
Service
Should the chain saw need service, take the tool to
your Authorized Service Dealer .
24
Storage
Important: Store the machine, battery pack, and
charger only in temperatures that are within the
appropriate range; refer to Specications ( page
1 1 ) .
Important: If you are storing the battery pack
for the off-season, charge it until 2 or 3 LED
indicators turn green on the battery . Do not store
a fully charged or fully depleted battery . When
you are ready to use the machine again, charge
the battery pack until the left indicator light turns
green on the charger or all 4 LED indicators turn
green on the battery .
• Disconnect the machine from the power supply
(i.e., remove the battery pack) and check for
damage after use.
• Clean all foreign material from the machine.
• Do not store the machine with the battery pack
installed.
• Store the machine, battery pack, and battery
charger in a well-ventilated place that is
inaccessible to children.
• Keep the machine, battery pack, and battery
charger away from corrosive agents such as
garden chemicals and de-icing salts.
• T o reduce the risk of serious personal injury , do
not store the battery pack outside or in vehicles.
• Store the machine, battery pack, and battery
charger in an enclosed clean, dry area.
Preparing the Battery Pack
for Recycling
Important: Upon removal, cover the terminals of
the battery pack with heavy-duty adhesive tape.
Do not attempt to destroy or disassemble the
battery pack or remove any of its components.
Lithium-ion battery packs labeled with the
Call2Recycle seal can be recycled at any
participating retailer or battery recycling
facility in the Call2Recycle program (US
and Canada only). T o locate a participating
retailer or facility closest to you, please call
1-800-822-8837 or visit www .call2recycle.org.
If you cannot locate a participating retailer or
facility nearby , or if your rechargeable battery
is not labeled with the Call2Recycle seal,
please contact your local municipality for more
information on how to responsibly recycle the
battery . If you are located outside of the US
and Canada, please contact your authorized
T oro distributor .
25
T roubleshooting
Perform only the steps described in these instructions. All further inspection, maintenance, and repair work
must be performed by an authorized service center or a similarly qualied specialist if you cannot solve the
problem yourself.
Always remove the battery from the tool when troubleshooting, inspecting, maintaining, or cleaning the tool.
Problem
Possible Cause Corrective Action
1. The battery pack is low on charge.
1. Charge the battery pack.
2. The battery pack is not fully seated.
2. Ensure that the battery pack is inserted
all the way into the housing.
3. The battery pack is over or under the
appropriate temperature range.
3. Move the battery pack to a place
where it is dry and the temperature is
between 5°C (41°F) and 40°C (104°F).
4. The battery pack has exceeded high
amperage limits.
4. Release the trigger , then press the
trigger switch.
5. There is moisture on the leads of the
battery pack.
5. Allow the battery pack to dry or wipe it
dry .
6. The chain brake is engaged. 6. Disengage the chain brake by moving
the chain brake rearward.
The chain saw does not run or does not
run continuously .
7. There is debris under the cover . 7. Remove the cover and clean out any
debris.
1. The chain is not properly seated on the
drive sprocket.
1. Install the chain and ensure that the
links are properly seated in the drive
sprocket.
The chain saw runs, but the chain does
not rotate.
2. There is debris under the cover . 2. Remove the cover and clean out any
debris.
The chain brake does not engage. 1. The chain brake is damaged. 1. Immediately take the chain saw to a
Authorized Service Dealer .
1. The chain is not tensioned correctly .
1. Set the proper tension on the chain.
2. The chain is dull or damaged. 2. Replace the chain.
3. The guide bar is bent or the grooves
are damaged.
3. Replace the guide bar
4. The chain is installed backward. 4. Install the chain correctly .
The chain saw does not properly cut.
5. The chain is not being lubricated
properly .
5. Check the oil level and ensure that oil
is owing to the chain.
1. The oil level is low .
1. Check the oil level.
2. The oil outlet is plugged.
2. Clean out debris from the oil outlet.
3. There is debris under the cover . 3. Remove the cover and clean out any
debris.
The chain oil is not lubricating properly .
4. The oil channel or groove in the guide
bar is plugged.
4. Clean out debris in the bar .
1. The battery pack is over or under the
appropriate temperature range.
1. Move the battery pack to a place
where it is dry and the temperature is
between 5°C (41°F) and 40°C (104°F).
2. The chain is dull or damaged. 2. Replace the chain.
3. The guide bar is bent or the grooves
are damaged.
3. Replace the guide bar
4. The machine is overloaded. 4. Apply less pressure when cutting.
The battery pack loses charge quickly .
5. The chain is not being lubricated
properly .
5. Check the oil level and ensure that oil
is owing to the chain.
26
Problem
Possible Cause Corrective Action
1. The battery charger is over or under
the appropriate temperature range.
1. Unplug the battery charger and move
it to a place where it is dry and the
temperature is between 5°C (41°F)
and 40°C (104°F).
The battery charger is not working.
2. The outlet that the battery charger is
plugged into does not have power .
2. Contact your licensed electrician to
repair the outlet.
The LED indicator light on the battery
charger is red.
1. The battery charger and/or battery
pack is over or under the appropriate
temperature range.
1. Unplug the battery charger and move
the battery charger and battery pack
to a place where it is dry and the
temperature is between 5°C (41°F)
and 40°C (104°F).
1. There is an error in the communication
between the battery pack and the
charger .
1. Remove the battery pack from the
battery charger , unplug the battery
charger from the outlet, and wait 10
seconds. Plug the battery charger into
the outlet again and place the battery
pack on the battery charger . If the LED
indicator light on the battery charger is
still blinking red, repeat this procedure
again. If the LED indicator light on
the battery charger is still blinking red
after 2 attempts, properly dispose of
the battery pack at a battery recycling
facility .
The LED indicator light on the battery
charger is blinking red.
2. The battery pack is weak.
2. Contact your authorized service dealer
if the battery is in warranty , or properly
dispose of the battery pack at a battery
recycling facility .
27
California Proposition 65 W arning Information
What is this warning?
Y ou may see a product for sale that has a warning label like the following:
W ARNING: Cancer and Reproductive Harm—www .p65W arnings.ca.gov .
What is Prop 65?
Prop 65 applies to any company operating in California, selling products in California, or manufacturing products that may be sold in or brought into
California. It mandates that the Governor of California maintain and publish a list of chemicals known to cause cancer , birth defects, and/or other
reproductive harm. The list, which is updated annually , includes hundreds of chemicals found in many everyday items. The purpose of Prop 65 is to
inform the public about exposure to these chemicals.
Prop 65 does not ban the sale of products containing these chemicals but instead requires warnings on any product, product packaging, or literature with
the product. Moreover , a Prop 65 warning does not mean that a product is in violation of any product safety standards or requirements. In fact, the
California government has claried that a Prop 65 warning “is not the same as a regulatory decision that a product is ‘safe’ or ‘unsafe.’” Many of these
chemicals have been used in everyday products for years without documented harm. For more information, go to https://oag.ca.gov/prop65/faqs-view-all .
A Prop 65 warning means that a company has either (1) evaluated the exposure and has concluded that it exceeds the “no signicant risk level”; or (2)
has chosen to provide a warning based on its understanding about the presence of a listed chemical without attempting to evaluate the exposure.
Does this law apply everywhere?
Prop 65 warnings are required under California law only . These warnings are seen throughout California in a wide range of settings, including but not
limited to restaurants, grocery stores, hotels, schools, and hospitals, and on a wide variety of products. Additionally , some online and mail order
retailers provide Prop 65 warnings on their websites or in catalogs.
How do the California warnings compare to federal limits?
Prop 65 standards are often more stringent than federal and international standards. There are various substances that require a Prop 65 warning
at levels that are far lower than federal action limits. For example, the Prop 65 standard for warnings for lead is 0.5 μg/day , which is well below
the federal and international standards.
Why don’t all similar products carry the warning?
• Products sold in California require Prop 65 labelling while similar products sold elsewhere do not.
• A company involved in a Prop 65 lawsuit reaching a settlement may be required to use Prop 65 warnings for its products, but other companies
making similar products may have no such requirement.
• The enforcement of Prop 65 is inconsistent.
• Companies may elect not to provide warnings because they conclude that they are not required to do so under Prop 65; a lack of warnings for a
product does not mean that the product is free of listed chemicals at similar levels.
Why does the manufacturer include this warning?
the manufacturer has chosen to provide consumers with as much information as possible so that they can make informed decisions about the products
they buy and use. the manufacturer provides warnings in certain cases based on its knowledge of the presence of one or more listed chemicals without
evaluating the level of exposure, as not all the listed chemicals provide exposure limit requirements. While the exposure from the manufacturer products
may be negligible or well within the “no signicant risk” range, out of an abundance of caution, the manufacturer has elected to provide the Prop 65
warnings. Moreover , if the manufacturer does not provide these warnings, it could be sued by the State of California or by private parties seeking to
enforce Prop 65 and subject to substantial penalties.
Rev A
