Safety Guide
DIGITAL FULL COLOR MULTIFUNCTIONAL SYSTEM
MODEL: MX-C357F
MX-C407F
MX-C507F
MX-C557F
MX-C607F
DIGITAL FULL COLOR PRINTER
MODEL: MX-C407P
MX-C507P
MX-C607P
DIGITAL MULTIFUNCTIONAL SYSTEM
MODEL: MX-B557F
MX-B707F
MX-B427W
MX-B467F
LASER PRINTER
MODEL: MX-B557P
MX-B707P
MX-B427PW
MX-B467P
CAUTION
CAUTION–POTENTIAL INJURY: To avoid the risk of fire or electrical shock, connect the power cord to
an appropriately rated and properly grounded electrical outlet that is near the product and easily
accessible.
CAUTION–POTENTIAL INJURY: To avoid the risk of fire or electrical shock, use only the power cord
provided with this product or the manufacturer's authorized replacement.
CAUTION–SHOCK HAZARD: This product uses an electronic power switch. It does not physically
disconnect the input AC voltage. To avoid the risk of electrical shock, always remove the power cord from
the printer when removal if the input AC voltage is required.
CAUTION–POTENTIAL INJURY: To reduce the risk of fire, use only a 26 AWG or larger
telecommunications (RJ-11) cord when connecting this product to the public switched telephone network.
For users in Australia, the cord must be approved by the Australian Communications and Media Authority.
CAUTION–POTENTIAL INJURY: This product uses a laser. Use of controls or adjustments or
performance of procedures other than those specified in the User's Guide may result in hazardous
radiation exposure.
This product may produce small amounts of ozone during normal operation, and may be equipped with a filter
designed to limit ozone concentrations to levels well below the recommended exposure limits. To avoid high
ozone concentration levels during extensive usage, install this product in a well-ventilated area and replace
the ozone and exhaust filters if instructed to do so in the product maintenance instructions. If there are no
references to filters in the product maintenance instructions, then there are no filters requiring replacement for
this product.
Supplier's Declaration of Conformity
SHARP DIGITAL FULL COLOR MULTIFUNCTIONAL SYSTEM,
MX-C357F / MX-C407F / MX-C507F / MX-C557F / MX-C607F
SHARP DIGITAL FULL COLOR PRINTER,
MX-C407P / MX-C507P / MX-C607P
SHARP DIGITAL MULTIFUNCTIONAL SYSTEM,
MX-B557F / MX-B707F / MX-B427W / MX-B467F
SHARP LASER PRINTER,
MX-B557P / MX-B707P / MX-B427PW / MX-B467P
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Responsible Party: SHARP ELECTRONICS CORPORATION
100 Paragon Drive, Montvale, New Jersey 07645
TEL: 1-800-BE-SHARP
Notice on products with 2.4GHz radio transmitter
This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.
EMC (this machine and peripheral devices)
WARNING:
Shielded interface cables must be used with this equipment to maintain compliance with EMC regulations.
This is a class A product. In a domestic environment this product may cause radio interference in which case
the user may be required to take adequate measures.
Please note that MX-C357F, MX-B427PW, MX-B427W, and MX-B467P are EMC Class B products.
These special accessories must be used with the device.
Each instruction also covers the optional units used with these products.
Required power supply
MX-C357F
AC 120 V ±10% 60 Hz 7.8 A 0.610 kW
MX-C407F / MX-C507F
AC 120 V ±10% 60 Hz 10.6 A 1.020 kW
MX-C557F / MX-C607F
AC 120 V ±10% 60 Hz 10.6 A 1.010 kW
MX-C407P
AC 120 V ±10% 60 Hz 7.6 A 0.600 kW
MX-C507P
AC 120 V ±10% 60 Hz 9.9 A 1.000 kW
MX-C607P
AC 120 V ±10% 60 Hz 10.2 A 0.910 kW
MX-B557F / MX-B707F
AC 120 V ±10% 60 Hz 10.4 A 0.975 kW
MX-B557P / MX-B707P
AC 120 V ±10% 60 Hz 9.8 A 1.035 kW
MX-B427PW / MX-B427W
AC 120 V ±10% 60 Hz 7.5 A 0.640 kW
MX-B467P / MX-B467F
AC 120 V ±10% 60 Hz 8.0 A 0.745 kW
Local voltage ±10%
MX-C357F
220–240 V: 3.9 A / 100–127 V: 7.8 A
0.610 kW / 0.610 kW
MX-C407F / MX-C507F
220–240 V: 5.7 A / 100–127 V: 10.6 A
1.020 kW / 1.020 kW
MX-C557F / MX-C607F
220–240 V: 5.3 A / 100–127 V: 10.6 A
1.010 kW / 1.010 kW
MX-C407P
220–240 V: 3.8 A / 100–127 V: 7.6 A
0.600 kW / 0.600 kW
MX-C507P
220–240 V: 5.1 A / 100–127 V: 9.9 A
1.000 kW / 1.000 kW
MX-C607P
220–240 V: 5.1 A / 100–127 V: 10.2 A
0.910 kW / 0.910 kW
MX-B557F / MX-B707F
220–240 V: 5.3 A / 100–127 V: 10.4 A
0.975 kW / 0.975 kW
MX-B557P / MX-B707P
220–240 V: 4.9 A / 100–127 V: 9.8 A
1.035 kW / 1.035 kW
MX-B427PW / MX-B427W
220–240 V: 3.8 A / 110–127 V: 7.5 A
0.640 kW / 0.640 kW
MX-B467P / MX-B467F
220–240 V: 4.0 A / 110–127 V: 8.0 A
0.745 kW / 0.745 kW
Operating environment
oт 10°C до 35°C (oт 50°F до 95°F)
(20–85% RH) 800
–1013 hPa
Noise emission
The noise emission can be viewed at the following URL address:
https://global.sharp/products/copier/products/
Laser information
The printer is certified in the U.S. to conform to the requirements of DHHS 21 CFR, Chapter I, Subchapter J
for Class I (1) laser products, and elsewhere is certified as a Class I laser product conforming to the
requirements of IEC 60825-1:2014.
Class I laser products are not considered to be hazardous. The laser system and printer are designed so
there is never any human access to laser radiation above a Class I level during normal operation, user
maintenance, or prescribed service conditions. The printer has a non-serviceable printhead assembly that
contains a laser with the following specifications:
Wavelength
Output Power
MX-C357F / MX-C407F / MX-C507F / MX-C407P / MX-C507P
650–670 nm
Max 15 mW
MX-C557F / MX-C607F / MX-C607P
755–800 nm
Max 20 mW
MX-B557F / MX-B707F / MX-B557P / MX-B707P
755–800 nm
Max 25 mW
MX-B427PW / MX-B427W
775–800 nm
Max 25 mW
MX-B467P / MX-B467F
650–670 nm
Max 15 mW
For your safety, observe the precautions below.
• Do not remove the cabinet, operation panel or any other covers.
• The equipment’s exterior doors and covers may contain safety interlocks. Do not bypass any safety
interlocks.
United Kingdom
MAINS PLUG WIRING INSTRUCTIONS
The mains lead of this equipment is already fitted with a mains plug which is either a non-rewireable
(moulded) or a rewireable type. Should the fuse need to be replaced, a BSI or ASTA approved fuse to
BS1362 marked ( ) or ( ) and of the same rating as the one removed from the plug must be used.
Always refit the fuse cover after replacing the fuse on the moulded plug.
Never use the plug without the fuse cover fitted.
In the unlikely event of the socket outlet in your home not being compatible with the plug supplied either cut-
off the moulded plug (if this type is fitted) or remove by undoing the screws if a rewireable plug is fitted and fit
an appropriate type observing the wiring code below.
DANGER: The fuse should be removed from the cut-off plug and the plug destroyed immediately and
disposed of in a safe manner. Under no circumstances should the cut-off plug be inserted elsewhere into a
13A socket outlet as a serious electric shock may occur.
To fit an appropriate plug to the mains lead, follow the instructions below:
IMPORTANT: The wires in this mains lead are coloured in accordance with the following code:
GREEN-AND-YELLOW: Earth
BLUE: Neutral
BROWN: Live
As the colours of the wires in this mains lead may not correspond with coloured markings identifying the
terminals in your plug, proceed as follows:
The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the plug which is
marked with the letter E, or by the safety earth symbol ( ) ,or coloured green or green and-yellow.
The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or
coloured black.
The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or
coloured red.
If you have any doubt, consult a qualified electrician.
WARNING: THIS APPARATUS MUST BE EARTHED.
For users of the FAX function
Important safety instructions
• If any of your telephone equipment is not operating properly, you should immediately remove it from your
telephone line, as it may cause harm to the telephone network.
• Never install telephone wiring during a lightning storm.
• Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.
• Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at
the network interface.
• Use caution when installing or modifying telephone lines.
• Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk
of electric shock from lightning.
• Do not use a telephone to report a gas leak in the vicinity of the leak.
• Do not install or use the machine near water, or when you are wet. Take care not to spill any liquids on the
machine.
• Save these instructions.
About the Telephone Consumer Protection Act of 1991
The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other
electronic device, including FAX machines, to send any message unless such message clearly contains in a
margin at the top or bottom of each transmitted page or on the first page of the transmission, the date and
time it is sent and an identification of the business or other entity, or other individual sending the message and
the telephone number of the sending machine or such business, other entity, or individual. (The telephone
number provided may not be a 900 number or any other number for which charges exceed local or long-
distance transmission charges.) In order to program this information into your FAX machine, you should
complete the following steps:
See “Setting up the printer to fax” in the User's Guide.
FCC Notice to users
This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA.
On this equipment is a label that contains, among other information, a product identifier in the format
US:AAAEQ##TXXXX.
If requested, this number must be provided to the telephone company.
The REN is used to determine the number of devices that may be connected to a telephone line.
Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call.
In most but not all areas, the sum of RENs should not exceed five (5.0).
To be certain of the number of devices that may be connected to a line, as determined by the total RENs,
contact the local telephone company.
For products approved after July 23, 2001, the REN for this product is part of the product identifier that has
the format US:AAAEQ##TXXXX.
The digits represented by ## are the REN without a decimal point (e.g., 03 is a REN of 0.3).
For earlier products, the REN is separately shown on the label.
If this equipment causes harm to the telephone network, your telephone company may disconnect your
service temporarily. If possible, They will notify you in advance. If advance notice is not practical, you will be
notified as soon as possible. You will also be advised of your right to file a complaint with the FCC.
Your telephone company may make changes in its facilities, equipment, operations, or procedures that could
affect the operation of your equipment. If this happens, the telephone company will provide advance notice in
order for you to make necessary modifications to maintain uninterrupted service. If the equipment is causing
harm to the telephone network, your telephone company may ask you to disconnect the equipment
until the problem is resolved.
If you have any questions or problems which cannot be solved by reading this manual, please contact:
A plug and jack used to connect this equipment to the premises wiring and telephone network must comply
with the applicable FCC Part 68 rules and requirements adopted by the ACTA.
See installation instructions for details. This equipment connects to the telephone network through a standard
USOC RJ-11C network interface jack. If your home has specially wired alarm equipment connected to the
telephone line, ensure the installation of this equipment does not disable your alarm equipment.
If you have questions about what will disable alarm equipment, consult your telephone company or a qualified
installer. This equipment may not be used on coin service provided by the telephone company.
Connection to party lines service is subject to state tariffs.
Contact your state's public utility commission, public service commission or corporation commission for more
information.
Notice for users in Canada
This product meets the applicable Innovation, Science and Economic Development Canada technical
specifications.
The Ringer Equivalence Number (REN) indicates the maximum number of devices allowed to be connected to
a telephone interface. The termination of an interface may consist of any combination of devices subject only
to the requirement that the sum of the RENs of all the devices not exceed five. The REN of this equipment is
indicated on the machine.
Avis pour nos utilisateurs au Canada
Le présent produit est conforme aux spécifications techniques applicables d'lnnovation, Sciences et
Développement économique Canada.
L'indice d'équivalence de la sonnerie (lES) sert à indiquer le nombre maximal de dispositifs qui peuvent être
raccordés à une interface téléphonique. La terminaison d'une interface peut consister en une combinaison
quelconque de dispositifs, à la seule condition que la somme des lES de tous les dispositifs n'excède pas
cinq. L'indice d'équivalence de la sonnerie (IES) de cet équipement est indiqué sur la machine.
India Only
Information on the Disposal of this Equipment
IF YOU WISH TO DISPOSE OF THIS EQUIPMENT, DO NOT USE THE ORDINARY WASTE BIN, AND DO
NOT PUT THEM INTO A FIREPLACE!
Used electrical and electronic equipment should always be collected and treated SEPARATELY in
accordance with law.
Separate collection promotes an environment-friendly treatment, recycling of materials, and minimizing final
disposal of waste. IMPROPER DISPOSAL can be harmful to human health and the environment due to
contained hazardous substances! Take USED EQUIPMENT to a local, usually municipal, collection facility,
where available.
If in doubt, contact your dealer or local authorities and ask for the correct method of disposal.
This equipment complies with the E-Waste (Management) Rules, 2016:
On restriction of the hazardous constituents as specified in rule 16 in electrical and electronic equipment.
For more information to recycle properly, please see the website.
https://www.sharpindia.co.in/default.html#/
