BAUMR-AG TOLMSCBM1C0A Forced Action Pan Mixer 1100W User Manual

User Manual

[Revision 1.0]

READ THIS MANUAL CAREFULLY BEFORE USE – FAILURE TO DO SO MAY RESULT IN INJURY, PROPERTY DAMAGE AND MAY

VOID WARRANTY. • KEEP THIS MANUAL FOR FUTURE REFERENCE. • Products covered by this manual may vary in

appearance, assembly, inclusions, specifications, description, and packaging.

MSC-10 Mortar Screed Concrete Mixer

E&OE © Baumr-AG 2

Safety

Safety messages are designed to alert you to possible dangers or hazards that could cause death, injury or

equipment or property damage if not understood or followed. Safety messages have the following symbols:

You WILL be KILLED or

SERIOUSLY INJURED if you do

not follow instructions.

You CAN be KILLED or

SERIOUSLY INJURED if you do

not follow instructions.

You CAN be INJURED if you do

not follow instructions or equipment

damage may occur.

It is vital that you read and understand this

user manual before using the product,

including safety warnings, and any assembly

and operating instructions. Keep the manual

for future reference.

Safety precautions and recommendations

detailed here must be fully understood and

followed to reduce the risk of injury, fire,

explosion, electrical hazard, and/or property

damage.

Safety information presented here is generic

in nature – some advice may not be

applicable to every product. The term

"equipment" refers to the product, be it

electrical mains powered, battery powered or

combustion engine powered.

• Before Use - If you are not familiar with the

safe operation/handling of the equipment or

are in any way unsure of any aspect of

suitability or correct use for your

application, you should complete training

conducted by a person or organization

qualified in safe use and operation of this

equipment, including fuel/electrical handling

and safety.

• Do NOT operate the equipment in

flammable or explosive environments, such

as in the presence of flammable liquids,

gases, or dust. The equipment may create

sparks or heat that may ignite flammable

substances.

• Keep clear of moving parts.

• Equipment may be a potential source of

electric shock or injury if misused.

• Do NOT operate the equipment if it is

damaged, malfunctioning or is in an

excessively worn state.

• Do NOT allow others to use the equipment

unless they have read this manual and are

adequately trained.

• Keep packaging away from children - risk

of suffocation! Operators must use the

equipment correctly. When using the

equipment, consider conditions and pay

due care to persons and property.

General Work Area Safety

• Wor

k areas should be clean and well it.

• Do not operate the equipment if

bystanders, animals etc are within

operating range of the equipment or the

general work area.

• If devices are provided for connecting dust

extraction / collection facilities, ensure

these are connected and used properly.

Dust collection can reduce dust-related

hazards.

General Personal Safety

• Wear

appropriate protective equipment

when operating, servicing, or when in the

operating area of the equipment to help

protect from eye and ear injury, poisoning,

burns, cutting and crush injuries. Protective

equipment such as safety goggles,

respirators, non-slip safety footwear, hard

hat, hearing protection etc should be used

for appropriate equipment / conditions.

Other people nearby should also wear

appropriate personal protective equipment.

Do not wear loose clothing or jewellery,

which can be caught in moving parts. Keep

hair and clothing away from the equipment.

• Stay alert and use common sense when

operating the equipment. Do not over-

reach. Always maintain secure footing and

balance.

• Do not use the equipment if tired or under

the influence of drugs, alcohol, or

medication.

• This equipment is not intended for use by

persons with reduced physical, sensory, or

mental capabilities.

General Fuel Safety

• P

etrol/fuel/gasoline is extremely flammable

– keep clear of naked flames or other

ignition sources.

• Do not spill fuel. If you spill fuel, wipe it off

the equipment immediately – if fuel gets on

your clothing, change clothing.

• Do NOT smoke near fuel or when

refuelling.

• Always shut off the engine before

refuelling.

• Do NOT refuel a hot engine.

• Open the fuel cap carefully to allow any

pressure build-up in the tank to release

slowly.

• Always refuel in well-ventilated areas.

• Always check for fuel leakage. If fuel

leakage is found, do not start, or run the

engine until all leaks are fixed.

General Carbon-Monoxide Safety

• U

sing a combustion engine indoors CAN

KILL IN MINUTES. Engine exhaust

contains carbon-monoxide – a poison you

cannot smell or see.

• Use combustion engines OUTSIDE only,

and far away from windows, doors, and

vents.

General Equipment Use and Care

• K

eep packaging away from children and

pets, potential risk of suffocation or

choking.

• The equipment is designed for domestic

use only.

• Handle the equipment safely and carefully.

• Before use, inspect the equipment for

misalignment or binding of moving parts,

loose components, damage, or any other

condition that may affect its operation. If

damaged, have the equipment repaired by

an authorised service centre or technician

before use.

• Prevent unintentional starting of the

equipment - ensure equipment and power

switches are in the OFF position before

connecting or moving equipment. Do not

carry equipment with hands or fingers

touching any controls. Remove any tools or

other items that are not a part of the

equipment from it before starting or

switching on.

• Do not force the equipment. Use the

correct equipment for your application.

Equipment will perform better and be safer

when used within its design and usage

parameters.

• Use the equipment and accessories etc. in

accordance with these instructions,

considering working conditions and the

work to be performed. Using the equipment

for operations different from those intended

could result in hazardous situations.

• Always keep equipment components

(engines, hoses, handles, controls, frames,

housings, guards etc) and accessories

(cutting tools, nozzles, bits etc) properly

maintained. Keep the equipment clean and,

where applicable, properly lubricated.

• Store the equipment out of reach of

children or untrained persons. To avoid

burns or fire hazards, let the equipment

cool completely before transporting or

storing. Never place or store the equipment

near flammable materials, combustible

gases, or liquids etc.

• The equipment is not weather-proof, and

should not be stored in direct sunlight, at

high ambient temperatures or locations that

are damp or humid.

• Do not clean equipment with solvents,

flammable liquids, or harsh abrasives.

• For specific equipment safety use and care,

see Equipment Safety.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

MSC-10 Mortar Screed Concrete Mixer

E&OE © Baumr-AG 3

General Electrical Safety

• I

nspect electrical equipment, extension

cords, power bars, and electrical fittings for

damage or wear before each use. Repair or

replace damaged equipment immediately.

• Ensure all power sources conform to

equipment voltage requirements and are

disconnected before connecting or

disconnecting equipment.

• When wiring electrically powered

equipment, follow all electrical and safety

codes.

• Always use a Residual Current Device

(RCD) (GFCI) / Earth Leakage Circuit

Breaker / Safety Switch when operating this

item (electrical items only).

• High voltage / high current power lines may

be present. Use extreme caution to avoid

contact or interference with power lines.

Electrical shock can be fatal.

General Electrical Safety

• E

lectrically grounded equipment must have

an approved cord and plug and be

connected to a grounded electrical outlet.

• Do NOT bypass the ON/OFF switch and

operate equipment by connecting and

disconnecting the electrical cord.

• Do NOT use equipment that has exposed

wiring, damaged switches, covers or

guards.

• Do NOT use electrical equipment in wet

conditions or in damp locations.

• Do NOT use electrical cords to lift, move or

carry equipment.

• Do NOT coil or knot electrical cords, and

ensure electrical cords are not trip hazards.

General Service Information

• T

he equipment must be serviced or

repaired at authorised service centres by

qualified personnel only.

• Replacement parts must be original

equipment manufacturer (OEM) to ensure

equipment safety is maintained.

• Do NOT attempt any maintenance or repair

work not described in this manual.

• After use, the equipment and components

may still be hot – allow the equipment to

cool and disconnect spark plugs and/or

electrical power sources and/or batteries

from it before adjusting, changing

accessories, or performing repair or

maintenance.

• Do NOT adjust while the equipment is

running.

• Perform service-related activities in suitable

conditions, such as a workshop.

• Replace worn, damaged or missing

warning/safety labels immediately.

Child Choking Hazard!

• W

ARNING: CHOKING HAZARD - CHILDREN UNDER 8 YRS. CAN CHOKE OR SUFFOCATE ON SMALL PARTS. ADULT

SUPERVISION REQUIRED.

• Carefully inspect anything a baby or child could gain access to, including this product & packaging.

• Dangers include anything of a size that could become stuck or lodged in a baby or child's airway.

• Dangers include things like raw, hard fruit and vegetable pieces, large pieces of meat, bones or sausage skins, popcorn, nuts,

hard lollies and corn chips, small magnets and batteries, coins, beads, marbles and small uninflated balloons, broken toys and smaller toys,

buttons, keys, and coins. But there are also many more.

• Pay particular attention to accessories, nuts, bolts, screws, washers, caps, covers, loose parts, parts that could be removed or break off, pieces

of packaging, staples, tape etc.

• In the case of any doubt, secure the item of concern in an appropriate manner, or completely remove the possibility of access by a baby or child.

HAZARDOUS COMPONENTS!

• BE

AWARE THAT THE EQUIPMENT MAY INCLUDE HAZARDOUS COMPONENTS, SUCH AS BLADES, HOT SURFACES AND MOVING

PARTS.

• MOVING BLADES CAN CAUSE SERIOUS INJURY AND EVEN DEATH IF USED IMPROPERLY OR WITHOUT SUFFICIENT PPE.

• DO NOT USE THIS EQUIPMENT ON UNEVEN SURFACES AND ALWAYS MAINTAIN GOOD BALANCE WHEN USING THIS EQUIPMENT.

FAILURE TO DO SO MAY CAUSE SERIOUS INJURY.

• MAINTAIN A SECURE GRIP OF THE TRIGGER ASSEMBLY AT ALL TIMES.

Understand Your Mixer

• R

ead and understand the owner’s manual and labels affixed to the mixer. Learn its application, limitations, and any specific hazards associated

with it.

• Familiarise yourself with the controls before operating the mixer.

Stay Alert

• D

o not operate the mixer while under the influence of drugs, alcohol, or any medication that could affect your ability to use it properly.

• Do not use the mixer when tired or distracted from the job at hand. Stay focused and use common sense.

Avoid Dangerous Conditions

• E

nsure adequate surrounding workspace. Keep your work area clean and well lit. Cluttered areas invite injuries. Keep the area around the mixer

clear of obstructions, grease, oil, trash, and other debris that could cause someone to fall onto moving parts.

• Only use or operate the mixer on solid, flat, level ground that is capable of supporting the weight of the mixer and its load to prevent tipping.

• Do not attempt to move the mixer when it is loaded and/or in operation.

• This mixer is designed for producing concrete, mortar, and plaster. It is not suitable for mixing flammable or explosive substances. Do not use it in

areas where fumes from paint, solvents, or flammable liquids could pose a hazard.

Inspect Your Mixer

• I

nspect your mixer before turning it on. Ensure guards are in place and functioning. Do not plug in the mixer with the motor cover off. Check all

bolts, nuts, and screws for tightness before each use, especially those securing guards and drive mechanisms. Mixing vibrations may loosen

them.

• Make it a habit to check that all adjusting tools, shovels, hand trowels, and other equipment are removed from the mixer area before turning it on.

• Replace damaged, missing, or failed parts before use. Warning labels carry important information. Replace any missing or damaged labels.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

MSC-10 Mortar Screed Concrete Mixer

E&OE © Baumr-AG 4

Dress Properly

• D

o not wear loose clothing, gloves, neckties, or jewellery (rings, watches) as they can be caught in moving parts. Protective non-conductive

gloves and non-skid footwear are recommended. Wear protective hair covering to contain long hair, preventing it from being caught in machinery.

Use a face or dust mask if the operation is dusty. Always wear safety goggles or face shields. Everyday eyeglasses have impact-resistant lenses

but are not safety glasses.

Do Not Abuse the Cord

• N

ever carry the mixer by its cord or pull the cord to disconnect it from the socket.

• Keep the cord away from heat, oil, and sharp edges.

Extension Cords

• E

xtension cords must not exceed 50 metres in length. The wire section should be 1.5mm² for 230V to ensure sufficient current flow to the motor.

Improper use of extension cords may cause inefficient operation, leading to overheating and motor damage.

• Use only extension cords that meet H07RN-F specification for outdoor use. Avoid using inadequately insulated or exposed connections.

Connections must be made with outdoor-suitable materials. Ensure the extension cord connections are dry and secure. Lay out the extension

cord carefully, avoiding liquids, sharp edges, and areas where vehicles might run over it. Avoid trapping the extension cord under the mixer. Fully

unroll the cord to prevent overheating and potential fires.

Avoid Electrical Shock

• E

nsure the electrical circuit is adequately protected and corresponds with the power, voltage, and frequency of the motor.

• Do not plug or unplug the mixer while standing in damp or wet areas. Avoid using the mixer in wet or damp conditions, and do not expose it to

rain.

• Prevent body contact with grounded surfaces such as pipes, radiators, and metal enclosures.

• Ensure your fingers do not touch the plug’s metal prongs when plugging or unplugging the mixer.

Keep Visitors and Children Away

• K

eep unauthorised persons away from the mixer.

• Do not allow children to handle, climb on, or sit in the mixer.

Do Not Overreach

• M

aintain proper footing and balance at all times when loading or unloading the mixer.

• Never stand on the mixer. Serious injury may occur if the mixer tips or if moving parts are unintentionally contacted. Do not store items above or

near the mixer that could prompt someone to stand on it to reach them.

Avoid Injury from Unexpected Accidents

• K

eep hands away from all moving parts. Do not place any part of your body or any tools like shovels into the drum during operation. Avoid

passing hands through clearances between the frame and support arm or between the drum and support arm.

Do Not Force the Tool

• I

t will perform better and more safely at its designed rate. Always work within the rated capacity.

• Do not start the motor if the drum is fully loaded. Do not turn the mixer off while full of concrete.

• Do not use the mixer for any purpose other than what it was intended for.

• The mixer should not be towed by any vehicle.

Never Leave the Mixer Running Unattended

• D

o not leave the mixer until it has come to a complete stop.

Disconnect Power

• N

ever open the motor cover without unplugging the mixer. Disconnect from the power supply when not in use, before moving, adjusting,

changing parts, cleaning, or working on the mixer. Consult the technical manual before servicing.

Maintain Your Mixer with Care

• C

lean the mixer immediately after use. Keep it clean for optimal and safe performance.

• Use only the manufacturer’s original replacement parts when maintaining the mixer.

Protect the Environment

• D

ispose of leftover materials at an authorised collection point or follow local regulations. Do not discharge into drains, soil, or water.

Store Idle Equipment

• S

tore the mixer in a dry location to prevent rust when not in use. Keep the mixer out of reach of children and others not qualified to use it.

Electrical Connection

• T

his mixer is double insulated to Class II protection and rated IP44D. The insulation remains effective only if original insulating parts are used for

repairs and the spaces between insulation are maintained.

• Double insulation eliminates the need for a three-wire grounded power cord and grounded power supply system. Double-insulated tools can use

either a two or three-wire extension cord.

• Do not connect either core to the earth pin.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

MSC-10 Mortar Screed Concrete Mixer

E&OE © Baumr-AG 5

• The use of a Residual Current Device (RCD) or earth leakage trip on 230V electrics is recommended. If using an extension cable, plug it directly

into the RCD.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

MSC-10 Mortar Screed Concrete Mixer

E&OE © Baumr-AG 6

Safety Symbols

The product may have safety warning labels attached to it, explained below. Understand the symbols on your

product and their meanings. If any stickers become unreadable, unattached etc., replace them.

Flammable Material Hazard

Flammable liquids, gases, or

substances etc may present.

Avoid ignition sources and open

flames. Danger of fire.

Read User Manual

Read and fully understand

product safety warnings,

operation, procedures etc before

using the product.

Use Hand Protection

Wear appropriate hand protection

and take due care as the product

or use of the product may present

hand hazards.

Carbon-Monoxide Hazard

Do not use the product in

confined areas or without

adequate ventilation. Carbon-

monoxide poisoning can be fatal.

Electrocution / Electrical Shock

Hazard

High voltage or high current

electricity may be present or

required by the product. Take

due care when handling electrical

products, cables, plugs and

leads. Electrical shock can be

fatal.

Toxic Fumes / Dust Hazard

Using the product or by-products

from use may produce fumes,

smoke or particles that could be

harmful if inhaled. Wear

appropriate breathing protection

and have adequate ventilation.

Explosive Material Hazard

Combustible liquids, gases, or

substances etc may be present.

Avoid ignition sources and open

flames. Danger of explosion.

Cutting / Amputation Hazard

The product may have blades,

edges or mechanical devices that

can cause severe cut injury to

fingers, limbs etc. Take due care

when handling and using the

product.

Crush Hazard

The product may have blades,

edges or mechanical devices that

can cause severe crush injury to

fingers, limbs etc. Take due care

when handling and using the

product.

Single Operator Only

The product must be operated by

a single person only. More than

one person operating the product

may introduce additional hazards.

Use Face Protection

Wear appropriate full-face

protection and take due care as

the product or use of the product

may present face and eye

hazards.

Use Foot Protection

Wear appropriate foot protection

and take due care as the product

or use of the product may present

foot hazards.

Use Eye / Ear / Head Protection

Wear appropriate eye and / or

ear and / or head protection and

take due care as the product or

use of the product may present

eye, hearing, and head hazards.

Running Hazard

Do not run on or near the product

as doing so may present a fall

hazard.

Diving Hazard

Do not dive into the product as

doing so may present a neck /

head injury hazard.

Adult Supervision Required

Always supervise children and

other users of a product to

prevent drowning or injury.

Skin Penetration / Puncture

Hazard

The product may produce

pressure, emit liquids or objects

that can cause severe injury to

fingers, limbs, blood etc. Take

due care when handling and

using the product.

Hot Surface Hazard

Be aware that the product may

produce high temperatures and

hot surfaces that can cause burn

injuries.

Flying Debris Hazard

Be aware that the product or use

of the product may present

hazards produced by flying

debris. Wear appropriate clothing

and protective devices.

Moving Parts Hazard

Be aware that the product

contains or uses mechanical

devices that move or rotate.

Always wait for moving parts to

stop fully before handling the

product, adjusting, maintenance

etc.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

MSC-10 Mortar Screed Concrete Mixer

E&OE © Baumr-AG 7

Carbon-Monoxide Hazard

Do not use the product in

confined areas or without

adequate ventilation. Carbon-

monoxide poisoning can be fatal.

Pull Hazard

Be aware that the product

contains or uses mechanical

devices that can pull in objects

and can cause severe injury to

fingers, limbs etc. Take due care

when handling and using the

product.

Slope / Fall Injury Hazard

Be aware that using the product

on sloping surfaces or in slippery

conditions may present additional

dangers from falls and contact

with blades, moving parts, hot

surfaces etc.

"Slam Dunk" Warning

Do NOT attempt "slam dunk"

manoeuvres as this may result in

severe injury due to falling,

product breakage or collapse etc.

Electrocution / Electrical Shock

Hazard - Outdoor

High voltage or high current

electricity may be present or

required by the product. Do NOT

use in rain, damp, or wet

conditions. Electrical shock can

be fatal.

Electrocution / Electrical Shock

Hazard - Disconnect

High voltage or high current

electricity may be present or

required by the product. Always

disconnect the product from the

electrical supply before handling

the product, adjusting,

maintenance etc.

Power Line Electrocution

Hazard

High voltage / high current power

lines may be present. Use

extreme caution to avoid contact

or interference with power lines.

Electrical shock can be fatal.

"Kick-Back" Hazard

High level of "kick-back" hazard

that can cause the machine to

suddenly rotate towards operator.

Kick-back injury can be fatal.

Winch Operator Position

Hazard

Do NOT stand between winch

and load. Do NOT use winch to

move people.

Winch Lift Hazard

Do NOT LIFT load vertically. Use

machine to PULL only.

Cable Hazard

Ensure that load bearing cable is

not kinked or knotted.

Winch Cable Hazard

Ensure that there is a minimum

number of cable coils on

winching mechanism.

Winch Hook Hazard

Carry hook to load – do NOT

throw or run.

Flash / Blinding Hazard

Wear appropriate eye protection

for welding. Direct exposure to

weld arcs may cause permanent

eye injury.

Laser Hazard

Laser may be in use – do NOT

look directly at laser or allow

others to.

Choking Hazard

Children under 8 yrs. Can choke

or suffocate on small parts. Adult

supervision required.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

MSC-10 Mortar Screed Concrete Mixer

E&OE © Baumr-AG 8

Table of Contents

Safety ......................................................................................................................................................... 2

Safety Symbols ........................................................................................................................................................... 6

Parts Identification .................................................................................................................................... 9

Assembly ................................................................................................................................................. 12

Main Frame ............................................................................................................................................................... 12

Gearbox Flange ........................................................................................................................................................ 13

Transmission Case ................................................................................................................................................... 13

Motor Cover .............................................................................................................................................................. 14

Drum ......................................................................................................................................................................... 15

Mixer Arm ................................................................................................................................................................. 16

Protective Net and the Discharge Port ..................................................................................................................... 17

Operation ................................................................................................................................................. 18

Loading ..................................................................................................................................................................... 18

Emptying ................................................................................................................................................................... 18

Cleaning .................................................................................................................................................................... 18

Maintenance ............................................................................................................................................. 19

Specifications .......................................................................................................................................... 20

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

MSC-10 Mortar Screed Concrete Mixer

E&OE © Baumr-AG 9

Parts Identification

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

MSC-10 Mortar Screed Concrete Mixer

E&OE © Baumr-AG 10

No. Part Name Qty

1 Mixer arms 1

2 Cover (drum lid) 1

3 Spring washer (8 mm) 5

4 Nut (M10) 4

5 Spring washer (10 mm) 4

6 Bolt M10 × 30 (round head, square neck) 4

7 Outside blade 1

8 Spring washer (6 mm, included with reducer) 4

9 Motor cover 1

10 Spring washer (6 mm) 4

11 Bolt M6 × 12 4

12 Flat washer (6 mm) 4

13 Nut (M6, included with reducer) 4

14 Flat washer (12 mm) 5

15 Spring washer (12 mm) 4

16 Flat washer (10 mm) 8

17 Switch plate 1

18 Power cord (power lead) 1

19 Cross-headed self-tapping screw (4 × 12) 4

20 Switch (KOA7) 1

21 Axle bracket 2

22 Right frame 1

23 Bolt M8 × 55 5

24 Flat washer (8 mm) 4

25 Left frame 1

26 Nut (M8) 4

27 8‑inch solid black rubber wheel 4

28 Small R‑pin (φ3) (snap ring) 4

29 Bolt M10 × 20 2

30 Self‑locking nut (M10) 4

31 Handle (folding/movable) 1

32 Bolt M10 × 50 4

33 Bolt M8 × 16 2

34 Chute (discharge opening) 1

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

MSC-10 Mortar Screed Concrete Mixer

E&OE © Baumr-AG 11

No. Part Name Qty

35 Reducer 1

36 Self‑locking nut (M12) 1

37 Discharge handle (weldment) 1

38 Reducer plate 1

39 Flat washer (6 mm, included with reducer) 4

40 Bolt M12 × 60 1

41 Bolt M12 × 30 4

42 Drum (weldment) 1

43 Inside blade 1

44 Shaft (drive shaft assembly) 1

45 Pin (8 × 30) 2

46 Pin (5 × 30) 2

47 Pin (3 × 30) 2

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

MSC-10 Mortar Screed Concrete Mixer

E&OE © Baumr-AG 12

Assembly

It is recommended that two people assist with the assembly.

Main Frame

1. Attach the frame as shown. Insert two shafts through the holes from one side, then slide the wheels over the

stub axles and secure them with the R pins.

2. Attach the frame arms in the same manner. Insert two M10x20 hex bolts through the holes from one side,

then place the nuts on the other side and tighten them down.

3. Attach the frame as shown. Insert an M8x55 bolt through the holes in the plate, then place the nuts, plate

washer, and spring washer on the other side. Tighten everything down.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

MSC-10 Mortar Screed Concrete Mixer

E&OE © Baumr-AG 13

Gearbox Flange

1. Place the reducer beneath the cross-connect panel.

2. Insert flat washers, lock washers, and M8 nuts. Tighten them securely.

Transmission Case

1. Place the reducer beneath the cross-connect panel.

2. Insert flat washers, lock washers, and M6 nuts. Tighten them down securely.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

MSC-10 Mortar Screed Concrete Mixer

Motor Cover

1. Place the drum cover on the drum.

2. Secure the motor cover using M8x16 bolts, flat washers, and lock washers. Tighten with the M8x16 bolts.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

MSC-10 Mortar Screed Concrete Mixer

Drum

1. Slide the drum onto the frame with the plate on the switch.

2. Insert two M10x50 hex bolts through the holes from one side, then secure with lock nuts on the other side.

Tighten them down securely.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

MSC-10 Mortar Screed Concrete Mixer

Mixer Arm

1. Insert the motor shaft into the drive axle sleeve, then insert the drive axle into the cross for the mixer arms.

Insert an M8x100 bolt and waterproof washers, then tighten securely.

2. Attach the blade to the frame using M10x20 bolts, lock washers, flat washers, and M10 nuts.

3. Fasten everything firmly using the M6x16 screws.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

MSC-10 Mortar Screed Concrete Mixer

Protective Net and the Discharge Port

1. Place the drum cover on the drum.

2. Insert an M10x100 bolt through the hole of the discharge chute, then add flat washers, lock washers, and

M10 nuts on the other side. Tighten securely, and then insert the discharge chute into the chute. Secure it

using an M8x20 bolt.

3. Mount the switch onto the frame as shown in the graphic. Fasten firmly using 4 sets of M5x12 screws, plate

washers, and spring washers.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

MSC-10 Mortar Screed Concrete Mixer

Operation

Loading

•

Completely unwind the extension cord. Connect it to the concrete mixer first before plugging it into the power

supply.

•

Always start the mixer before loading the drum. Load the drum while it is rotating.

•

Do not throw material into the mixer to avoid it sticking firmly to the back of the drum. Steadily trickle the

material over the rim.

Note: A built-in thermal protector is fitted in the motor to prevent overheating. The thermal protector will

reset automatically once the motor cools down.

For best results, follow these steps:

1. Add the required amount of gravel into the drum.

2. Add the required amount of cement into the drum.

3. Add the required amount of sand into the drum.

4. Pour the required amount of water into the drum.

Emptying

Do not turn the mixer off while it is still full. Empty the drum while it is rotating.

Cleaning

Never put your hands inside the drum while it is rotating.

•

Thoroughly clean the mixer at the end of each day’s operation. Keep your mixer clean, as even the smallest

trace of material left in the drum will harden and attract more each time you use it, eventually rendering the

machine useless.

•

Dried cement should be scraped out of the drum. Do not throw bricks into the mixer drum to clean it. Do not

hit the drum with a shovel, hammer, or other tools to break up dried cement, as this may damage the mixer.

•

The drum may be scoured for approximately 2 minutes using a 1" gravel and water mixture. Then, discharge

the gravel/water mixture and hose down the drum assembly inside and out.

•

The IP44D protection class construction of the concrete mixer allows you to hose down the drum assembly

safely.

•

Do not pour or spray water directly over the motor cover, especially over the openings in it.

•

Wipe off any external material from the motor cover. Do not use petrol, turpentine, lacquer, paint thinner, dry-

cleaning fluids, or similar products. The use of chemical products or solvents may affect the properties of the

cover, which is made of high-density polyethylene (HDPE).

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

MSC-10 Mortar Screed Concrete Mixer

Maintenance

ATTENTION: Surface corrosion will occur on metal surfaces over time and the rate of oxidation depends

on factors such as proximity to the ocean and humidity or condensation of water vapour on metal

surfaces. To mitigate this, WD40 can be used to remove surface corrosion then, when applied

periodically, it will prevent rust from forming.

•

Safety First: Always ensure the extension cord is unplugged before removing the motor cover to prevent

electrical shock or accidental start-up.

•

Belt Maintenance: The mixer is equipped with a preset, tensioned belt. No adjustments are necessary. Only

apply a touch of grease on the spindle to ensure smooth operation.

•

Bearing Maintenance: The bearings are sealed for life and require no maintenance or lubrication.

•

The wiring diagram and parts schematic in this manual are provided as reference tools only. Neither the

manufacturer nor distributor makes any representation or warranty that the buyer is qualified to make repairs

to the product or to replace any of its parts.

•

Only qualified technicians should perform repairs on the mixer. Any maintenance or repairs involving

electrical components must be carried out by a qualified electrician.

•

Parts indicated in a circle should only be fitted by a qualified electrician.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

MSC-10 Mortar Screed Concrete Mixer

Specifications

Drum Capacity 100L

Voltage 240V

Power (Watts) 1100W

Oil Type 10W-30 | 10W-40 | 15W-40

Drum Speed 23 RPM

Body Material Steel

Finish Powder-coated

Power Type Corded Electric

Drum Diameter 610mm

Wheels 8-inch rubber

Power Plug 10A Australian Standard

Note: Requires assembly

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Some experts believe that the incorrect or prolonged use of almost any

product may cause serious injury or death. To help reduce your risk of

serious injury or death, refer to the information below. For more information,

see www.datastreamserver.com/safety



Consult all documentation, packaging,

and product labelling before use. Note

that some products feature

documentation available online. It is

recommended to print and retain the

documentation.



Before each use, check the product for

loose/broken/damaged/missing parts,

wear, or leaks (if applicable). Never use a

product with

loose/broken/damaged/missing parts,

wear, or leaks.



Products must be inspected and serviced

(if applicable) by a qualified technician

every 6 months. This is based on

average residential use by persons of

average size and strength, and on a

property of average metropolitan size.

Use beyond these recommendations may

require more frequent

inspections/servicing.



Ensure that all users of the product have

completed a suitable industry recognised

training course before being allowed

access to the product.



The product has been supplied by a general merchandise

retailer that may not be familiar with your specific

application or description of application. Be sure to attain

third-party approval from a qualified specialist for your

application before use, regardless of any assurances from

the retailer or its representatives.



This product is not intended for use where fail-safe

operation is required. As with any product (for example,

automobile, computer, toaster), there is the possibility of

technical issues that may require the repair or

replacement of parts, or the product itself. If the possibility

of such failure and the associated time it may take to

rectify could in any way inconvenience the user, business,

or employee, or financially affect the user, business, or

employee, then the product is not suitable for your

requirements. This product is not intended for use where

incorrect operation or a failure of any kind, including but

not limited to, a condition requiring product return,

replacement, parts replacement, or service by a

technician may cause financial loss, loss of employee

time or an inconvenience requiring compensation.



If this product has been purchased in error when

considering the information presented here, contact the

retailer directly for details of their returns policy, if

required.

diagrams, or images may be reproduced or transmitted in any form or by any means, electronic or

mechanical, including photocopying, scanning, or recording, or any information storage and retrieval system,

without express permission or consent from the publisher.

BAUMR-AG TOLMSCBM1C0A Forced Action Pan Mixer 1100W

Product's Documents

Product manual

Specifications

BAUMR-AG TOLMSCBM1C0A Questions and Answers