UNDERCUPBOARD
INSTALLATION & USER
INSTRUCTIONS
2023
Qasair Rangehoods Installation Instructions2
Qasair Rangehoods Installation Instructions
3
Important Information
Cutout Dimensions
Duct Direction Change Instructions
Instructions for Models
FA
Instructions for Models
CON / NDCH / LIS / ETN
Instructions for Models
KEN / WCV
Remote Switching Specications
Installation Ideas
Instructions for Models
WES / EAS / GRA
Operation Details, Rangehood Cleaning, Filter Cleaning
6
4
7
8
10
19
24
31
39
34
33
Guarantee Exclusions
41
Appliance Guarantee
40
Instructions for Models
SP-RHQ
42
Standard Warranty / Extended Warranty
Qasair Rangehoods Installation Instructions4
The installation of Qasair Rangehoods must comply with the information in this booklet. Qasair Rangehoods are
designed and made to work efciently over all domestic cookware available on the Australian market.
It is necessary to allow electrical disconnection of the rangehood after installation.
This may be achieved by either.
a) Installing a power point to an accessible area for the rangehood.
b) Incorporating a wall switch to the xed wiring that supplies the rangehood.
Clearance from cooktop to Rangehood
For electric hot plate cooktops
Please follow the manufacturers instructions / recommendations.
For Induction cooktops
Induction cooktops may present problems with condensation on lters of rangehoods.
All Qasair rangehoods installed above an induction cooktop must be installed no less than 750mm between the
induction cooktop and the rangehood, with the exception of the Eastmore (EAS) rangehood which can be installed
no less than 600mm and the Grampian which can be installed no less than 650mm. Undermount (NDCH), Conley
(CON) and Foldaway (FA) rangehoods are not suitable for induction cooktops.
For gas cooktops
All Qasair Rangehood installations over a gas appliance must comply with (AS/NZS 5601.1).
The requirements for the installation of Gas Appliances (AS/NZS 5601.1) states that the rangehood be installed as
per the Rangehood and gas cooking appliance manufacturers instructions. Where a difference occurs, the greater
clearance shall apply. If no dimension is specied, the clearance between the supporting surface for the cooking
vessel of the gas cooking appliance and the rangehood shall not be less than 650mm.
If the gas appliance is designed for use without a cooking vessel (as dened by AS/NZS 5601.1), then the clearance
from the cooking surface to the grease lter shall be no less than 1200mm.
The recommendation for Qasair wallmount rangehoods is that they be installed between 700 to 800mm above the
supporting surface of the cooking vessel. When the rangehood is installed in a galley or partially enclosed kitchen
the rangehood can be installed between 900 to 1000mm above the highest part of the supporting surface of the
cooking vessel.
It is recommended that Qasair island rangehoods not be installed any higher than 800mm above the highest part of
the supporting surface of the cooking vessel as any movement around the bench will result in fumes being drawn
out from the catchment area of the rangehood with the exception of the Thermidor and Liverpool which for aesthetic
reasons is installed ush with the ceiling.
Ducting
For all your ducting requirements please refer to the Qasair Rangehoods Ducting Pieces brochure included
with your Rangehood or please consult our website where it can be viewed or downloaded.
1. Every Qasair rangehood must be ducted to the outside atmosphere by the use of zinc-alume duct or
non-porous and non-ammable materials. Do not use of any type of exible ducting or plastic PVC piping.
Rangehoods must not be vented into a wall cavity or a ceiling space. Externally ducting the rangehood prevents
a build up of grease, which can be a re risk. Ensure the external outlet vent does not restrict the airow in any
way, as this may result in reduced performance.
2. Qasair rangehoods must be ducted in duct work equivalent to the outlet of the rangehood ie: The cross
sectional area of the rangehood outlet and the duct work must be equal. Do not reduce the duct size or have
sharp bends. Enlarge the duct size if the duct is to run 6 metres or longer. Advice from Condari is available to
ensure optimum performance. Always use non-ammable materials to minimise the risk of re in the duct.
3. Ensure all ducting pieces are correctly tted and sealed with either duct tape or silicone to ensure that fumes
do not escape into the ceiling space and seep into living areas through vents or light ttings.
IMPORTANT INFORMATION
Qasair Rangehoods Installation Instructions
5
Other Important Information
1. Rangehoods and other cooking fume extractors may adversely effect the safe operation of appliances burning
gas or other fuels (including those in other rooms) due to the back ow of combustion gases. These gases
can potentially result in carbon monoxide poisoning. After installation of a Rangehood or other cooking fume
extractor, the operation of ued gas appliances should be tested by a competent person to ensure that back ow
of combustion gases does not occur.
2. WARNING: Incorrect venting will result in additional noise and a reduction in efciency. Exhaust air must not be
discharged into any chimney or ue, which may carry combustible products from other sources.
a) Do not discharge the air-ow from the rangehood into a ue used for exhausting fumes
from burning gas or fuel;
b) For cleaning purposes please refer to page 39 of installation instructions for stainless steel;
c) If cleaning is not carried out in accordance with the instructions as listed on page 39, there may be an
increased risk of re;
d) Some parts of the rangehood may become hot when cooking;
e) This appliance is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a person responsible for their safety. Children should be
supervised to ensure that they do not play with the appliance.
3. The installation and tting of the rangehood should be done in such a way that will allow the unit to be removed
if service is required. Additional costs incurred in the removal of wall tiles, damage to walls or bench tops are not
covered by warranty.
4. To reduce the risk of xing screws coming in contact with live parts, do not drill or screw into the rangehood.
Live wires are encapsulated where possible to prevent user contact. If necessary drill from the inside out and
only through single sheet material.
5. NOTE: Condari recommend an air movement of between 1000 to 1400 cubic metres per hour over an indoor
barbecue, depending on the length of the duct run. Ensure a twin motor unit is installed over indoor barbecues
for optimum results. Barbecues should be positioned under the centre of the hood where the fans are mounted
and not near the outer edges where leakage may occur.
6. The lights in the rangehoods are LED and come with a night light except for D400L-1 and SEN400L-1.
7. Please contact Condari to arrange an authorised technician to replace any cracked protective glass shields for
the LED lights.
8. If the supply cord is damaged, an authorised service centre or licensed electrician must replace it.
9. Do not ambé under the rangehood.
10. Qasair domestic rangehoods must not to be used over barbecues approved for outdoor use only. Condor make a
range of rangehoods specically for outdoor barbecues in alfresco areas under the Condor name.
11. Condari can manufacture rangehoods to be used over commercial cookers in domestic applications.
12. NOTE: All information is correct at the time of print, as standards vary over time please ensure all requirements
meet the latest standards / codes and regulations.
Qasair Rangehoods Installation Instructions6
INSTALLATION INSTRUCTIONS
CUTOUT DIMENSIONS
MODEL HOOD SIZE BASE SIZE
PROUD MOUNT
CUT OUT DIMENSION
FLUSH MOUNT
CUT OUT DIMENSION
CON 60L 244 x 580 280 x 600 258 x 585 283 x 603
CON 80L
244 x 780 280 x 800 258 x 785 283 x 803
ETN 600L 344 x 580 380 x 600 355 x 585 383 x 603
ETN 900L 344 x 880 380 x 900 355 x 885 383 x 903
ETN 1200L 344 x 1180 380 x 1200 355 x 1185 383 x 1203
GRA 60L 364 x 560 400 x 600 370 x 565 403 x 603
GRA 90L 364 x 880 400 x 900 370 x 885 403 x 903
GRA 100L 364 x 980 400 x 1000 370 x 985 403 x 1003
GRA 120L 364 x 1160 400 x 1200 370 x 1165 403 x 1203
KEN 1000L 564 x 980 600 x 1000 570 x 985 603 x 1003
KEN 1300L 564 x 1280 600 x 1300 570 x 1285 603 x 1303
KEN 1600L 564 x 1580 600 x 1600 570 x 1585 603 x 1603
LIS 500L 393 x 480 430 x 500 400 x 485 433 x 503
LIS 800L 393 x 780 430 x 800 400 x 785 433 x 803
LIS 900L 393 x 870 430 x 900 400 x 885 433 x 903
LIS 1000L 393 x 980 430 x 1000 400 x 985 433 x 1003
LIS 1200L 393 x 1180 430 x 1200 400 x 1185 433 x 1203
LIS 1500L 393 x 1480 430 x 1500 400 x 1485 433 x 1503
NDCH 90L 244 x 880 280 x 900 258 x 885 283 x 903
NDCH 100L 244 x 980 280 x 1000 258 x 985 283 x 1003
NDCH 120L 244 x 1180 280 x 1200 258 x 1185 283 x 1203
WES 60L / EAS 60L 294 x 565 330 x 600 300 x 570 333 x 603
WES 80L / EAS 80L 294 x 780 330 x 800 300 x 785 333 x 803
WES 90L / EAS 90L 294 x 880 330 x 900 300 x 885 333 x 903
WES 100L / EAS 100L 294 x 980 330 x 1000 300 x 985 333 x 1003
WES 120L / EAS 120L 294 x 1180 330 x 1200 300 x 1185 333 x 1203
WCV 1000L 564 x 980 600 x 1000 570 x 985 603 x 1003
WCV 1300L 564 x 1280 600 x 1300 570 x 1285 603 x 1303
WCV 1600L
564 x 1580 600 x 1600 570 x 1585 603 x 1603
Qasair Rangehoods Installation Instructions
7
DUCT DIRECTION CHANGE INSTRUCTIONS
Before installing your rangehood check whether it has the fan mounted for back or top ducting.
For top ducting, the unit will have the air outlet at the top, and for back ducting, the unit will have the air outlet at the
back.
To change from top to back or back to top, proceed as follows:
Duct direction for ETN, NDCH and CON models
The motor shown is fitted to the back plate (P) and this plate is attached to the rangehood by screws (S). To change
from top to back, remove the filters, unplug fan(s). Undo all the screw (S), carefully remove the plate and turn it around
so the motor points out the way required. Fit and reconnect the fan(s), and fit all the screws again and tighten.
Duct direction for LIS / FA / EAS / WES / GRA and KEN
To change the duct direction, proceed as follows:
1. Remove the screws from the fan access panel and remove access panel (for EAS and WES models only).
2. Disconnect fan(s).
3. Unscrew the 2 x 7mm screws (B) fixing the fan to the hood. Remove fan entirely. Repeat for each fan.
4. Rotate the fan assembly and re-install so that the air outlet meets with the rangehood outlet hole through which
you are going to vent (top or back).
5. Replace the 2 x 7mm screws holding each fan.
6. Reconnect the fan(s)
7. Refit the fan access panel (for EAS and WES models only).
Rear Duct Position
Top Duct Position
Qasair Rangehoods Installation Instructions
8
INSTALLATION INSTRUCTIONS
• FA
1. The rangehood is designed to be fitted within joinery and can be installed by inserting screws in the three holes
provided on each side, or to the top or back by drilling your own mounting holes as required.
2. Lift rangehood into position ensuring correct orientation of the rangehood with switches facing the operator when
cooking.
3. When installed, cover the access holes to the side fixing screws with the plastic plugs supplied.
4. Fit filters.
5. Install front panel to suit as per your kitchen design.
Installation must be carried out by the procedure outlined.
Failure to do so may void the guarantee.
Electrical: Wiring to the appliance must comply with State and local Regulations.
Connection to be carried out by a registered electrician.
Qasair Rangehoods Installation Instructions
9
Door Width
Condari Pty Ltd. Page 1 of 1
Version: E 06/10/2022F
Body Width
Model
Motor Qty
Light Centres
Light Qty
Nightlight
LED Light
Filter Qty
Model
Filter Size
Conversion
Top/Back Back/Top
Electrical Connection
Minimum Height
(H =)
Maximum Height
(H =)
Coating
Available
All-thread
Fixing Centres
Corner Type
FA 60L-1 FA 90L-2FA 90L-1FA 60L-1FA 90L-2FA 90L-1
598mm
Centre
2
573.4mm
1
Cool
YES
1
274mm x 290mm
YES
10 Amp Lead
N/A
N/A
N/A
N/A
Square
898mm
873.4mm
1
Cool
YES
2
350mm
2
898mm
873.4mm
2
Cool
YES
2
350mm
2
424mm x 290mm
YES
10 Amp Lead
N/A
N/A
N/A
N/A
Square
424mm x 290mm
YES
10 Amp Lead
N/A
N/A
N/A
N/A
Square
ACFALR
Foldaway
Technical Specification Sheet
FA
Undercupboard
Power Entry
300
449
20
4
44
20
D
o
o
r
W
i
d
t
h
B
o
d
y
W
i
d
t
h
2
3
5
2
3
5
D
o
o
r
W
i
d
t
h
B
o
d
y
W
i
d
t
h
Power Entry
This view is shown
with door in closed
position.
200
110
1
0
2
3
5
2
3
5
1
0
0
9
2
3
5
2
3
5
1
0
0
FOLDAWAY - FA
Qasair Rangehoods Installation Instructions
10
INSTALLATION INSTRUCTIONS
• CON
• NDCH
• LIS
• ETN
1. Loosen screws A and B by turning anti-clockwise.
2. Turn screw ‘D’ anti-clockwise to extend the outer spring bracket.
3. Insert rangehood into cut out ensuring correct orientation of the rangehood with switches facing the operator when
cooking.
4. Turn screw ‘C’ clockwise to align rangehood with cupboard base, do not over tighten.
5. Tighten screw ‘A’ by turning clockwise to lock xing bracket.
6. Fit off ductwork as required.
7. To remove rangehood, turn screw ‘D’ clockwise.
Models: ETN
NDCH
Models: LIS
CON
RANGEHOOD SPRING BRACKETS
MOUNTING POSITION
Installation must be carried out by the procedure outlined.
Failure to do so may void the guarantee.
Electrical: Wiring to the appliance must comply with State and local Regulations.
Connection to be carried out by a registered electrician.
Flush Mount ( 1 : 4 )Proud Mount ( 1 : 4 )
AAB B
Cupboard
Front of Rangehood
FLUSH MOUNT
Cupboard
Front of Rangehood
PROUD MOUNT
12
12
Qasair Rangehoods Installation Instructions
11
Motor Box /
Flue Width
Condari Pty Ltd. Page 1 of 1
Version: E 06/10/2022
FF
Body Width
Model
Motor Qty
Light Centres
Light Qty
Nightlight
LED Light
Filter Qty
Model
Filter Size
Conversion
Top/Back Back/Top
Electrical Connection
Minimum Height
(H =)
Maximum Height
(H =)
Coating
Available
All-thread
Fixing Centres
Corner Type
CON 60L-1 CON 80L-2CON 80L-1CON 60L-1CON 80L-2CON 80L-1
600mm
Centre
2
580mm
1
Cool
YES
1
269mm x 250mm
YES
10 Amp Lead
N/A
N/A
N/A
N/A
Square
800mm
780mm
1
Cool
YES
2
379mm
2
800mm
780mm
2
Cool
YES
2
379mm
2
379mm x 157mm
YES
10 Amp Lead
N/A
N/A
N/A
N/A
Square
379mm x 157mm
YES
10 Amp Lead
N/A
N/A
N/A
N/A
Square
ACULR
Conley
Technical Specification Sheet
CON
Undercupboard
PMS 539C
R= 0
G= 48
B= 73
PMS 5503C
R= 156
G= 197
B= 202
Power Entry
B
o
d
y
W
i
d
t
h
M
o
t
o
r
B
o
x
W
i
d
t
h
1
0
4
0
B
o
d
y
W
i
d
t
h
M
o
t
o
r
B
o
x
W
i
d
t
h
280
360
12
10
2
5
3
0
Power Entry
10
110
9
18 18
244
2
3
5
2
3
5
2
3
5
1
0
0
CONLEY - CON
Qasair Rangehoods Installation Instructions
12
Undermount
Technical Specification Sheet
NDCH
Undercupboard
Motor Qty
LED Light
Nightlight
Model
Body Width
Motor Box /
Flue Width
Light Qty
Light Centres
Filter Qty
Cool
YES
1
880mm
900mm
NDCH 90L-1
2
Page 1 of 2
All-thread
Fixing Centres
Condari Pty Ltd.
Coating
Available
2
770mm
NDCH 90L-2
2
770mm
880mm
Minimum Height
(H =)
Model
Maximum Height
(H =)
Corner Type Square
N/AN/A
Version: E 06/10/2022F
Square
Electrical Connection
N/A
N/A
340mm x 260mm
YES
NDCH 90L-1 NDCH 90L-2
Cool
YES
900mm
2
2
10 Amp Lead
Y
ES
340mm x 260mm
10 Amp Lead
N/A
Filter Size
Conversion
Top/Back Back/Top
N/A
N/A
N/A
ACULR
Power entry location
is the same for all
NDCH models.
280
360
M
o
t
o
r
B
o
x
W
i
d
t
h
M
o
t
o
r
B
o
x
W
i
d
t
h
2
3
5
2
5
3
0
2
3
5
1
0
0
2
3
5
B
o
d
y
W
i
d
t
h
B
o
d
y
W
i
d
t
h
110
10
10
12
1818
244
9
UNDERMOUNT - NDCH
Qasair Rangehoods Installation Instructions
13
Undermount
Technical Specification Sheet
NDCH
Undercupboard
2
Light Centres
Filter Qty
860mm
Motor Box /
Flue Width
Body Width
Motor Qty
Nightlight
Light Qty
LED Light
1060mm
Cool
NDCH 120L-2
1180mm
YES
2
NDCH 100L-2
Cool
980mm
Model
2
All-thread
Fixing Centres
Page 2 of 2
Version: E 06/10/2022F
Condari Pty Ltd.
2
Corner Type
Maximum Height
(H =)
2
1000mm 1200mm
Filter Size
Electrical Connection
Minimum Height
(H =)
Square
N/A
N/A N/A
Square
Model
Coating
Available
N/A
N/A
10 Amp Lead
N/A
N/A
YES
479mm x 260mm
N/A
NDCH 100L-2
YES
NDCH 120L-2
10 Amp Lead
379mm x 260mm
YES
2
Conversion
Top/Back Back/Top
ACULR
Power entry location
is the same for all
NDCH models.
M
o
t
o
r
B
o
x
W
i
d
t
h
B
o
d
y
W
i
d
t
h
M
o
t
o
r
B
o
x
W
i
d
t
h
B
o
d
y
W
i
d
t
h
2
5
3
0
2
3
5
1
0
0
2
3
5
2
3
5
2
3
5
1
0
0
110
9
244
18 18
12
10
10
110
360
280
UNDERMOUNT - NDCH
Qasair Rangehoods Installation Instructions
14
Motor Box /
Flue Width
Condari Pty Ltd. Page 1 of 3
Version: E 06/10/2022F
Body Width
Model
Motor Qty
Light Centres
Light Qty
Nightlight
LED Light
Filter Qty
Model
Filter Size
Conversion
Top/Back Back/Top
Electrical Connection
Minimum Height
(H =)
Maximum Height
(H =)
Coating
Available
All-thread
Fixing Centres
Corner Type
LIS 500L-1 LIS 800L-2LIS 800L-1LIS 500L-1LIS 800L-2LIS 800L-1
500mm
Centre
1
480mm
1
Cool
YES
1
459mm x 290mm
YES
10 Amp Lead
N/A
N/A
N/A
N/A
Square
800mm
780mm
1
Cool
YES
2
380mm
2
800mm
780mm
2
Cool
YES
2
380mm
2
379mm x 290mm
YES
10 Amp Lead
N/A
N/A
N/A
N/A
Square
379mm x 290mm
YES
10 Amp Lead
N/A
N/A
N/A
N/A
Square
ACULR
Lismore
Technical Specification Sheet
LIS
Undercupboard
PMS 539C
R= 0
G= 48
B= 73
PMS 5503C
R= 156
G= 197
B= 202
Power entry location
is the same for all
LIS models.
M
o
t
o
r
B
o
x
W
i
d
t
h
B
o
d
y
W
i
d
t
h
1
1
5
5
0
2
3
5
315
110
20
20
110
400
12
20 20
393
430
9
75
150
M
o
t
o
r
B
o
x
W
i
d
t
h
B
o
d
y
W
i
d
t
h
2
3
5
2
3
5
1
0
0
2
3
5
2
3
5
2
3
5
1
0
0
LISMORE - LIS
Qasair Rangehoods Installation Instructions
15
Lismore
Technical Specification Sheet
LIS
Undercupboard
Motor Box /
Flue Width
Body Width
Light Centres
LED Light
Light Qty
Motor Qty
Filter Qty
2
424mm
Model Model LIS 900L-2
2
480mm
Nightlight
N/A
Minimum Height
(H =)
Page 2 of 3Condari Pty Ltd.
All-thread
Fixing Centres
Coating
Available
Maximum Height
(H =)
Corner Type
Conversion
Top/Back Back/Top
Electrical Connection
YES
N/A
10 Amp Lead
N/A
Square
N/A
Version: E 06/10/2022F
N/A
424mm x 290mm
2
LIS 1000L-2
2
Cool
YES
LIS 900L-2
900mm
870mm
2
10 Am
p Lead
YES
479mm x 290mm
LIS 1000L-2
N/A
Square
Cool
YES
980mm
1000mm
2
Filter Size
N/A
N/A
ACULR
Power entry location
is the same for all
LIS models.
150
75
9
430
393
2020
12
400
110
20
20
110
315
M
o
t
o
r
B
o
x
W
i
d
t
h
5
0
1
1
5
2
3
5
1
0
0
2
3
5
M
o
t
o
r
B
o
x
W
i
d
t
h
B
o
d
y
W
i
d
t
h
2
3
5
1
0
0
2
3
5
B
o
d
y
W
i
d
t
h
2
3
5
2
3
5
1
0
0
2
3
5
2
3
5
1
0
0
LISMORE - LIS
Qasair Rangehoods Installation Instructions
16
Minimum Height
(H =)
Filter Size
Model
Conversion
Top/Back Back/Top
N/A
LIS 1200L-3
Electrical Connection
Page 3 of 3
Body Width
Motor Box /
Flue Width
Motor Qty
Model
Nightlight
Filter Qty
Light Qty
Version: E 06/10/2022F
Light Centres
Maximum Height
(H =)
Corner Type
Condari Pty Ltd.
1180mm
1200mm
LIS 1200L-2
4
LED Light
580mm
YES
N/A
N/A
10 Amp Lead
290mm x 290mm
LIS 1200L-2
N/A
LIS 1500L-3
N/A
YESYES
2
N/A
290mm x 290mm 365mm x 290mm
All-thread
Fixing Centres
Coating
Available
LIS 1500L-3
1500mm
1480mm
3
3
1200mm
1180mm
452mm
4
YES
4
Cool Cool
3
2
LIS 1200L-3
N/A
Square
YES
10 Amp Lead10 Amp Lead
YES
N/A
Square
N/A
N/A
N/A
Square
N/A
580mm
2
Cool
ACULR
Lismore
Technical Specification Sheet
LIS
Undercupboard
Power entry location
is the same for all
LIS models.
M
o
t
o
r
B
o
x
W
i
d
t
h
315
110
20
20
110
400
12
20 20
393
430
9
75
150
B
o
d
y
W
i
d
t
h
1
1
5
5
0
2
3
5
1
0
0
2
3
5
B
o
d
y
W
i
d
t
h
2
3
5
1
0
0
2
3
5
1
0
0
2
3
5
M
o
t
o
r
B
o
x
W
i
d
t
h
2
3
5
2
3
5
2
3
5
1
0
0
1
0
0
2
3
5
2
3
5
1
0
0
LISMORE - LIS
Qasair Rangehoods Installation Instructions
17
Eaton
Technical Specification Sheet
ETN
Undercupboard
Motor Qty
LED Light
Nightlight
Model
Body Width
Motor Box /
Flue Width
Light Qty
Light Centres
Filter Qty
Cool
YES
1
580mm
600mm
ETN 600L-1
2
Page 1 of 2
All-thread
Fixing Centres
Condari Pty Ltd.
Coating
Available
2
800mm
ETN 900L-1
1
520mm
880mm
Minimum Height
(H =)
Model
Maximum Height
(H =)
Corner Type Square
N/AN/A
Version: G 06/10/2022F
Square
Electrical Connection
N/A
N/A
479mm x 290mm
YES
ETN 600L-1 ETN 900L-1
Cool
YES
900mm
1
2
10 Amp Lead
Y
ES
379mm x 290mm
10 Amp Lead
N/A
Filter Size
Conversion
Top/Back Back/Top
N/A
N/A
N/A
ACULR
Power entry location
is the same for
all ETN models.
2
3
5
2
0
1
7
10
290
12
380
2
3
5
M
o
t
o
r
B
o
x
W
i
d
t
h
B
o
d
y
W
i
d
t
h
M
o
t
o
r
Bo
d
y
W
i
d
t
h
B
o
d
y
W
i
d
t
h
110
9
10
18 18
344
110
EATON - ETN
Qasair Rangehoods Installation Instructions
18
Eaton
Technical Specification Sheet
ETN
Undercupboard
2
Light Centres
Filter Qty
800mm
Motor Box /
Flue Width
Body Width
Motor Qty
Nightlight
Light Qty
LED Light
1060mm
Cool
ETN 1200L-2
1180mm
YES
2
ETN 900L-2
Cool
880mm
Model
2
All-thread
Fixing Centres
Page 2 of 2
Version: G 06/10/2022F
Condari Pty Ltd.
3
Corner Type
Maximum Height
(H =)
2
900mm 1200mm
Filter Size
Electrical Connection
Minimum Height
(H =)
Square
N/A
N/A N/A
Square
Model
Coating
Available
N/A
N/A
10 Amp Lead
N/A
N/A
YES
340mm x 290mm
N/A
ETN 900L-2
YES
ETN 1200L-2
10 Amp Lead
379mm x 290mm
YES
2
Conversion
Top/Back Back/Top
ACULR
Power entry location
is the same for
all ETN models.
2
0
1
7
1
0
0
2
3
5
2
3
5
10
10
290
12
380
M
o
t
o
r
B
o
x
W
i
d
t
h
M
o
t
o
r
Bo
x
W
i
d
t
h
B
o
d
y
W
i
d
t
h
1
0
0
2
3
5
2
3
5
110
9
B
o
d
y
W
i
d
t
h
18 18
344
110
EATON - ETN
Qasair Rangehoods Installation Instructions
19
INSTALLATION INSTRUCTIONS
• KEN
• WCV
1. Remove inner side cover panels by removing screws at top of panel, from the inside of the rangehood to allow
access to spring brackets for adjustments.
2. Loosen screws A and B by turning anti-clockwise.
3. Turn screw ‘D’ anti-clockwise to extend the outer spring bracket.
4. Insert rangehood into cut out ensuring correct orientation of the rangehood with switches facing the operator when
cooking.
5. Turn screw ‘C’ clockwise to align rangehood with cupboard base, do not over tighten.
6. Tighten screw ‘A’ by turning clockwise to lock xing bracket.
7. Fit off ductwork as required.
8. To remove rangehood, turn screw ‘D’ clockwise.
Installation must be carried out by the procedure outlined.
Failure to do so may void the guarantee.
Electrical: Wiring to the appliance must comply with State and local Regulations.
Connection to be carried out by a registered electrician.
Models: KEN
RANGEHOOD SPRING BRACKETS
MOUNTING POSITION
Flush Mount ( 1 : 4 )Proud Mount ( 1 : 4 )
AAB B
Cupboard
Front of Rangehood
FLUSH MOUNT
Cupboard
Front of Rangehood
PROUD MOUNT
12
12
Qasair Rangehoods Installation Instructions
20
KEN 1300L-3KEN 1000L-2
Corner Type
Condari Pty Ltd.
Maximum Height
(H =)
Coating
Available
Minimum Height
(H =)
Electrical Connection
Conversion
Top/Back Back/Top
Filter Size
ModelKEN 1300L-3
All-thread
Fixing Centres
KEN 1000L-2
Body Width
Motor Box /
Flue Width
Motor Qty
LED Light
Light Centres
Filter Qty
Model
Nightlight
Light Qty
Page
1 of 2
Version: F 06/10/2022F
2
Cool
YES
2
580mm
3
1000mm
980mm
N/A
N/A
N/A
Square
10 Amp Lead
N/A
YES
290mm x 422mm
N/A
N/A
N/A
Square
10 Amp Lead
N/A
YES
290mm x 422mm
KENT
Technical Specification Sheet
KEN
Undercupboard
4
580mm
2
YES
Cool
3
1280mm
1300mm
ACULR
Power entry location
is the same for all
KEN models.
B
o
d
y
W
i
d
t
h
4
8
4
564
600
12
700
20
20
422
400
2
5
M
o
t
o
r
B
o
x
W
i
d
t
h
M
o
t
o
r
B
o
x
W
i
d
t
h
B
o
d
y
W
i
d
t
h
1
0
0
2
3
5
2
3
5
2
3
5
2
3
5
1
0
0
105
105
2
3
5
2
3
5
2
3
5
1
0
0
1
0
0
2
3
5
2
3
5
2
3
5
1
0
0
1
0
0
Recommended Installation height 800mm above the cooking surface
of an indoor compliant open flame BBQ or high powered Cookware.
503
KENT - KEN
Qasair Rangehoods Installation Instructions
21
KEN 1600L-4
Corner Type
Condari Pty Ltd.
Maximum Height
(H =)
Coating
Available
Minimum Height
(H =)
Electrical Connection
Conversion
Top/Back Back/Top
Filter Size
Model
All-thread
Fixing Centres
KEN 1600L-4
Body Width
Motor Box /
Flue Width
Motor Qty
LED Light
Light Centres
Filter Qty
Model
Nightlight
Light Qty
Page 2 of 2
Version: F 06/10/2022F
4
Cool
YES
4
375mm
5
1600mm
1580mm
N/A
N/A
N/A
Square
10 Amp Lead
N/A
YES
290mm x 422mm
KENT
Tec
hnical Specification Sheet
KEN
Undercupboard
ACULR
Power entry location
is the same for all
KEN models.
B
o
d
y
W
i
d
t
h
400
422
20
20
700
12
600
564
4
8
4
M
o
t
o
r
B
o
x
W
i
d
t
h
2
5
105
105
2
3
5
2
3
5
2
3
5
1
0
0
1
0
0
2
3
5
2
3
5
2
3
5
1
0
0
1
0
0
2
3
5
2
3
5
Recommended Installation height 800mm above the cooking surface
of an indoor compliant open flame BBQ or high powered Cookware.
503
KENT - KEN
Qasair Rangehoods Installation Instructions
22
WCV 1300L-3WCV 1000L-2
Corner Type
Condari Pty Ltd.
Maximum Height
(H =)
Coating
Available
Minimum Height
(H =)
Electrical Connection
Conversion
Top/Back Back/Top
Filter Size
ModelWCV 1300L-3
All-thread
Fixing Centres
WCV 1000L-2
Body Width
Motor Box /
Flue Width
Motor Qty
LED Light
Light Centres
Filter Qty
Model
Nightlight
Light Qty
Page
1 of 2
Version: E 06/10/2022F
2
Cool
YES
4
580mm
3
1000mm
980mm
N/A
N/A
N/A
Square
10 Amp Lead
N/A
YES
290mm x 422mm
N/A
N/A
N/A
Square
10 Amp Lead
N/A
YES
290mm x 422mm
COBAR
Technical Specification Sheet
WCV
Undercupboard
4
580mm
4
YES
Cool
3
1280mm
1300mm
ACULR
Power entry location
is the same for all
WCV models.
M
o
t
o
r
B
o
x
W
i
d
t
h
M
o
t
o
r
B
o
x
W
i
d
t
h
B
o
d
y
W
i
d
t
h
B
o
d
y
W
i
d
t
h
5
0
3
1
3
2
3
5
2
3
5
1
0
0
2
3
5
2
3
5
2
3
5
1
0
0
1
0
0
2
3
5
2
3
5
1
0
0
110
340
110
20
20
500
600
564
12
280
2
3
5
2
3
5
2
3
5
1
0
0
1
0
0
9
205
FILTER
279
FILTER
COBAR - WCV
Qasair Rangehoods Installation Instructions
23
WCV 1600L-3
Corner Type
Condari Pty Ltd.
Maximum Height
(H =)
Coating
Available
Minimum Height
(H =)
Electrical Connection
Conversion
Top/Back Back/Top
Filter Size
Model
All-thread
Fixing Centres
WCV 1600L-3
Body Width
Motor Box /
Flue Width
Motor Qty
LED Light
Light Centres
Filter Qty
Model
Nightlight
Light Qty
Page 2 of 2
Version: D 06/10/2022F
3
Cool
YES
4
872mm
5
1600mm
1580mm
N/A
N/A
N/A
Square
10 Amp Lead
N/A
YES
290mm x 422mm
COBAR
Technical Specification Sheet
WCV
Undercupboard
ACULR
Power entry location
is the same for all
WCV models.
M
o
t
o
r
B
o
d
y
W
i
d
t
h
B
o
d
y
W
i
d
t
h
2
3
5
2
3
5
2
3
5
1
0
0
1
0
0
2
3
5
2
3
5
2
3
5
1
0
0
1
0
0
3
1
3
5
0
11020
110
20
340
12
500
600
564
280
9
205
FILTER
279
FILTER
COBAR - WCV
Qasair Rangehoods Installation Instructions
24
INSTALLATION INSTRUCTIONS
• WES
• EAS
• GRA
1. Loosen screws A and B by turning anti-clockwise.
2. Turn ‘D’ anti-clockwise to extend the outer spring bracket.
3. Insert rangehood into cut out ensuring correct orientation of the rangehood with switches facing the operator when
cooking.
4. Turn screw ‘C’ clockwise to align rangehood with cupboard base. Do not over tighten.
5. Tighten screw ‘A’ by turning clockwise to lock xing bracket.
6. Fit off ductwork as required.
7. To remove rangehood, turn screw ‘D’ clockwise.
Installation must be carried out by the procedure outlined.
Failure to do so may void the guarantee.
Electrical: Wiring to the appliance must comply with State and local Regulations.
Connection to be carried out by a registered electrician.
Model: WES
Model: EAS, GRA
WESTMORE
EASTMORE
RANGEHOOD SPRING BRACKETS
A
B
C
B
C
D
D
A
MOUNTING POSITION
Flush Mount ( 1 : 4 )Proud Mount ( 1 : 4 )
AAB B
Cupboard
Front of Rangehood
FLUSH MOUNT
Cupboard
Front of Rangehood
PROUD MOUNT
12
12
The Westmore (WES) rangehood must be installed at a minimum of 750mm over induction cooktops
The Eastmore (EAS) rangehood can be installed at a minimum of 600mm over induction cooktops
The Grampian (GRA) rangehood can be installed at a minimum of 650mm over induction cooktops
Qasair Rangehoods Installation Instructions
25
Eastmore
Technical Specification Sheet
EAS
Undercupboard
PMS 539C
R= 0
G= 48
B= 73
PMS 5503C
R= 156
G= 197
B= 202
Motor Qty
LED Light
Nightlight
Model
Body Width
Motor Box /
Flue Width
Light Qty
Light Centres
Filter Qty
Cool
YES
1
565mm
600mm
EAS 60L-1
2
Page 1 of 2
All-thread
Fixing Centres
Condari Pty Ltd.
Coating
Available
2
380mm
EAS 80L-2
2
300mm
780mm
Minimum Height
(H =)
Model
Maximum Height
(H =)
Corner Type Square
N/AN/A
Version: G 06/10/2022F
Square
Electrical Connection
N/A
N/A
272mm x 272mm
YES
EAS 60L-1 EAS 80L-2
Cool
YES
800mm
2
2
10 Amp Lead
YES
379mm x 260mm
10 Amp Lead
N/A
Filter Size
Conversion
Top/Back Back/Top
N/A
N/A
N/A
ACULR
Power entry location
is the same for all
EAS models.
Motor Access
Panel
Motor Access
Panel
M
o
t
o
r
B
o
x
W
i
d
t
h
2
3
5
3
0
4
5
2
3
5
1
0
0
2
3
5
330
12
FILTER
330
20
20
294
FILTER
225
570
B
o
d
y
W
i
d
t
h
B
o
d
y
W
i
d
t
h
2
3
5
2
3
5
1
0
0
2
3
5
M
o
t
o
r
B
o
x
W
i
d
t
h
110
9
110
EASTMORE - EAS
Qasair Rangehoods Installation Instructions
26
Eastmore
Technical Specification Sheet
EAS
Undercupboard
N/A
10 Amp Lead
N/A
YES
N/A
479mm x 260mm
N/A
Square
N/A
N/A N/A
N/A N/A
SquareSquare
Coating
Available
Condari Pty Ltd.
Maximum Height
(H =)
EAS 100L-2
2
900mm 1200mm
680mm
3
2
1160mm
1000mm
2
480mm
2
YES
Cool
980mm
YES
2
Cool
Minimum Height
(H =)
N/A
10 Amp Lead
YES
379mm x 260mm
N/A
10 Amp Lead
EAS 90L-2
YES
Cool
2
880mm
2
Motor Qty
Model
429mm x 260mm
N/A
YES
2
430mm
Light Centres
Filter Size
ModelEAS 120L-2 EAS 90L-2
Corner Type
All-thread
Fixing Centres
Elect
rical Connection
Conversion
Top/Back Back/Top
EAS 100L-2 EAS 120L-2
Filter Qty
Nightlight
Light Qty
LED Light
Body Width
Motor Box /
Flue Width
Version: G 06/10/2022F
Page 2 of 2
ACULR
Power entry location
is the same for all
EAS models.
Motor Access
Panel
Motor Access
Panel
M
o
t
o
r
B
o
x
W
i
d
t
h
B
o
d
y
W
i
d
t
h
B
o
d
y
W
i
d
t
h
2
3
5
1
0
0
2
3
5
2
3
5
2
3
5
1
0
0
2
3
5
2
3
5
1
0
0
M
o
t
o
r
B
o
x
W
i
d
t
h
3
0
4
5
9
11020
570
FILTER
225
294
20
FILTER
330
12
330
110
EASTMORE - EAS
Qasair Rangehoods Installation Instructions
27
Westmore
Technical Specification Sheet
WES
Undercupboard
PMS 539C
R= 0
G= 48
B= 73
PMS 5503C
R= 156
G= 197
B= 202
Motor Qty
LED Light
Nightlight
Model
Body Width
Motor Box /
Flue Width
Light Qty
Light Centres
Filter Qty
Cool
YES
1
565mm
600mm
WES 60L-1
2
Page 1 of 2
All-thread
Fixing Centres
Condari Pty Ltd.
Coating
Available
2
380mm
WES 80L-2
2
300mm
780mm
Minimum Height
(H =)
Model
Maximum Height
(H =)
Corner Type Square
N/AN/A
Version: G 06/10/2022F
Square
Electrical Connection
N/A
N/A
272mm x 272mm
YES
WES 60L-1 WES 80L-2
Cool
YES
800mm
2
2
10 Amp Lead
YES
379mm x 260mm
10 Amp Lead
N/A
Filter Size
Conversion
Top/Back Back/Top
N/A
N/A
N/A
ACULR
Power entry location
is the same for all
WES models.
M
o
t
o
r
B
o
x
W
i
d
t
h
3
0
4
5
Motor Access
Panel
Motor Access
Panel
2
3
5
2
3
5
2
3
5
1
0
0
2
3
5
2
3
5
1
0
0
2
3
5
330
12
FILTER
145
450
20
20
294
FILTER
60
B
o
d
y
W
i
d
t
h
B
o
d
y
W
i
d
t
h
M
o
t
o
r
B
o
x
W
i
d
t
h
110
9
110
WESTMORE - WES
Qasair Rangehoods Installation Instructions
28
Westmore
Technical Specification Sheet
WES
Undercupboard
N/A
N/A
mm x mm
N/A
N/A
N/A
Square
N/A
479mm x 260mm
N/A
10 Amp Lead
YES
10 Amp Lead
YES
N/A
379mm x 260mm
YES
N/A
N/A
10 Amp lead
Model
Conversion
Top/Back Back/Top
2
3
2
Corner Type Square
1160mm
1200mm
YES
WES 120L-2
680mm
2
Cool
YES
Cool
480mm
2
2
980mm
1000mm
2
Cool
880mm
430mm
2
Light Qty
2
YES
Electrical Connection
Maximum Height
(H =)
Minimum Height
(H =)
Filter Size
Coating
Available
N/A
N/A
429mm x 260mm
WES 100L-2
900mm
All-thread
Fixing Centres
Condari Pty Ltd.
WE
S 90L-2 WES 120L-2WES 90L-2 WES 100L-2
Motor Qty
Nightlight
Filter Qty
Motor Box /
Flue Width
Model
Body Width
Light Centres
LED Light
Version: G 06/10/2022F
Page 2 of 2
ACULR
Power entry location
is the same for all
WES models.
Motor Access
Panel
Motor Access
Panel
M
o
t
o
r
B
o
x
W
i
d
t
h
B
o
d
y
W
i
d
t
h
2
3
5
1
0
0
2
3
5
2
3
5
1
0
0
2
3
5
2
3
5
1
0
0
2
3
5
B
o
d
y
W
i
d
t
h
3
0
4
5
M
o
t
o
r
B
o
x
W
i
d
t
h
110
9
110
FILTER
60
294
20
20
450
FILTER
145
12
330
WESTMORE - WES
Qasair Rangehoods Installation Instructions
29
Grampian
Technical Specification Sheet
GRA
Undercupboard
PMS 539C
R= 0
G= 48
B= 73
PMS 5503C
R= 156
G= 197
B= 202
Motor Box /
Flue Width
Body Width
LED Light
Motor Qty
Model
Coating
Available
Maximum Height
(H =)
501mm
GRA 600L-1
600mm
Cool
GRA 900L-2
2
430mm
All-thread
Fixing Centres
Corner Type
Condari Pty Ltd.
Light Centres
Light Qty
Nightlight
Page 1 of 2
Filter Qty
Electrical Connection
Conversion
Top/Back Back/Top
Model
Minimum Height
(H =)
N/A
YES
10 Amp Lead
479mm x 260mm
GRA 600L-1
1
280mm
YES
N/A
N/A
Square
N/A
Square
N/A
N/A
10 Amp Lead
Version: E 06/10/2022F
N/A2 2
YES
880mm
Cool
2
900mm
1
Filter Size
429mm x 260mm
N/A
GRA 900L-2
YES
ACULR
Power entry locations
are the same for all
GRA models.
B
o
d
y
W
i
d
t
h
M
o
t
o
r
B
o
x
W
i
d
t
h
M
o
t
o
r
B
o
x
W
i
d
t
h
B
o
d
y
W
i
d
t
h
1
1
5
5
0
110
20
285
110
20
500
400
Filter
185
12
75
364
Filter
250
75
2
3
5
2
3
5
1
0
0
2
3
5
2
3
5
1
0
0
9
2
3
5
2
3
5
GRAMPIAN - GRA
Qasair Rangehoods Installation Instructions
30
Grampian
Technical Specification Sheet
GRA
Undercupboard
Version: E 06/10/2022F
N/A
Square
N/A
Square
N/A
N/A
10 Amp Lead
GRA 1200L-2
YES
379mm x 260mm
N/A
GRA 1000L-2
YES
479mm x 260mm
Page 2 of 2
N/A
N/A
N/A
10 Amp Lead
Body Width
Motor Box /
Flue Width
Nightlight
Motor Qty
LED Light
Light Qty
981mm
2
Cool
YES
2
1161mm
2
Cool
YES
3
600mm
2
GRA 1200L-2
1200mm
Model
1000mm
GRA 1000L-2
Filter Qty
2
Light Centres
480mm
Condari Pty Ltd.
Corner Type
Coating
Available
Conversion
Top/Back Back/Top
Filt
er Size
Model
Electrical Connection
Maximum Height
(H =)
All-thread
Fixing Centres
Minimum Height
(H =)
ACULR
PMS 5503C
R= 156
G= 197
B= 202
Power entry locations
are the same for all
GRA models.
75
Filter
250
364
75
12
Filter
185
400
B
o
d
y
W
i
d
t
h
M
o
t
o
r
B
o
x
W
i
d
t
h
M
o
t
o
r
B
o
x
W
i
d
t
h
B
o
d
y
W
i
d
t
h
1
1
5
5
0
500
20
110
285
20
110
2
3
5
2
3
5
1
0
0
2
3
5
2
3
5
1
0
0
9
2
3
5
2
3
5
1
0
0
2
3
5
2
3
5
1
0
0
GRAMPIAN - GRA
Qasair Rangehoods Installation Instructions
31
INSTALLATION INSTRUCTIONS
• SP-RHQ
Special Rangehood Qasair - SP-RHQ - Rangehoods are custom made and will vary
in shape, size, qty. of fans and mounting configuration, depending on application
and requirements. If in doubt please consult with Condari on how to install your
SP-RHQ Rangehood.
Qasair Rangehoods Installation Instructions
32
SP-RHQ
Corner Type
Condari Pty Ltd.
Maximum Height
(H =)
Coating
Available
Minimum Height
(H =)
Electrical Connection
Conversion
Top/Back Back/Top
Filter Size
Model
All-thread
Fixing Centres
SP-RHQ
Body Width
Motor Box /
Flue Width
Motor Qty
LED Light
Light Centres
Filter Qty
Model
Nightlight
Light Qty
Page
1 of 1
Version: A 10/10/2022
T.B.D.
Cool
/ Warm
YES / NO
T.B.D.
T.B.D.
T.B.D.
T.B.D.
T.B.D.
T.B.D.
T.B.D.
T.B.D.
T.B.D.
T.B.D.
T.B.D.
YES / NO
T.B.D.
Special Rangehood
Technical Specification Sheet
SP-RHQ
Undercupboard
ACULR
SPECIAL RANGEHOOD QASAIR - SP-RHQ -
RANGEHOODS ARE CUSTOM MADE.
SPECIFICATION DRAWING IS PROVIDED
SEPARATELY PRIOR TO MANUFACTURE.
EE
XX
AA
MM
PP
LL
EE
SS
OO
NN
LL
YY
SPECIAL - SP-RHQ
Qasair Rangehoods Installation Instructions
33
REMOTE SWITCHING SPECIFICATIONS
3 FAN, LED and NIGHTLIGHT
1. Wiring to the appliance must comply with State and local regulations.
2. Switching is not provided with this unit.
3. You may use any approved switching to connect the rangehood (e.g. Clipsal switches).
4. All fans must be controlled by at least one ON/OFF and one HI/LO switch.
5. Please refer to wiring diagram below for detailed wiring information.
AC1
AC2
LED
AC2
AC1
LED
BLUE
BLUE
BROWN
BLUE
BLACK
BLUE
BROWN
E
DRAWING NUMBER
CIRCUIT DIAGRAM
DESIGNER
CHECKED
M. Malesevic
REVISION
CONDARI PTY LTD
DATE
8 Argent Place, Ringwood VIC 3134
Ph: (03) 9873 5877 / Fx: (03) 9873 5748
REM SW 3 FAN LED NL
REMOTE SWITCH 3 FAN LED NIGHT LIGHT
B
27/02/2020
S.Stopher
JUNCTION BOXES INSIDE RANGEHOOD
NOTES:-
1. ALL FANS MUST BE CONTROLLED BY
AT LEAST ONE ON/OFF AND ONE
HI/LO SWITCH WIRED IN SERIES TO
ENSURE ACTIVE VOLTAGE FOR HIGH
AND LOW IS NOT APPLIED TO THE
FAN AT THE SAME TIME.
2. THE WIRING FOR THE FANS -
LOW SPEED - BROWN
HIGH SPEED - BLACK
NEUTRAL - BLUE
3. THE WIRING FOR THE LIGHTS -
FULL LIGHT - BLACK
NEUTRAL - BLUE
NIGHT LIGHT - BROWN
4. EARTH TERMINAL ADJACENT
JUNCTION BOXES
BROWN
BLACK
FAN 2 & 3
JUNCTION
BOX
FAN 1
JUNCTION
BOX
LIGHTING
JUNCTION
BOX
BLUE
BROWN
BLACK
BLUE
BROWN
BLUE
BLACK
www.condari.com.au
WIRING DIAGRAM
For further information, please contact Condari Pty Ltd
phone: 03 9482 7088 fax: 03 9482 7011
NOTE: This diagram is for reference only. A qualied electrician must connect re-
mote switching to rangehood.
Reected in this drawing is the most common method of connecting the rangehood.
Be aware that active voltage must NOT be applied to both the ‘Black-High’ or
‘Brown-Low’ wires at the same time. This will cause the fan to fail.
E
FAN SW
HI / LOW
FAN
FAN SW
ON / OFF
L
N
E
DRAWING NUMBER
CIRCUIT DIAGRAM
DESIGNER
CHECKED
M. Malesevic
REVISION
CONDARI PTY LTD
DATE
8 Argent Place, Ringwood VIC 3134
Ph: (03) 9873 5877 / Fx: (03) 9873 5748
FAN WIRING
FAN WIRING
A
21/09/2019
BLUE
BLACK
S. Stopher
LOW
BROWN
COM
HIGH
RANGEHOOD
Qasair Rangehoods Installation Instructions
34
3. FA 60L-1 T 4. FA 60L-1 T
5. FA 60L-1 T
6. FA 60L-1 T / FA 60L-1 B
INSTALLATION IDEAS
For all your ducting requirements please refer to the Qasair rangehoods ducting pieces brochure included
with your rangehood or please consult our website where it can be viewed or downloaded.
Condari recommends Qasair and Condor rangehoods be installed using ducting that is:
• rigid
• non-ammable
• correctly sized
This will ensure that maximum air movement with minimum noise levels is acheived.
Ducting incorrectly, with exible or smaller diameter ducting will dramatically reduce the air movement and increase
the noise level of the rangehood and will void the manufacturer’s warranty.
The installation ideas below will give you some guidelines on how to correctly duct your Qasair and Condor Range-
hood using Qasair and Condor ducting pieces.
FA 60L-1 T
FA 60L-1 B
Rangehood
FA 60L-1 T
Rangehood
FA 60L-1 T
Rangehood
FA 60L-1 T
Rangehood
Qasair Rangehoods Installation Instructions
35
7. FA 90L-2 T 8. FA 90L-2 T
9. FA 90L-2 T 10. FA 90L-2 B
11. FA 90L-2 T 12. FA 90L-2 T
FA 90L-2 T
Rangehood
FA 90L-2 T
Rangehood
FA 90L-2 T
Rangehood
FA 90L-2 T
Rangehood
FA 90L-2 T
Rangehood
FA 90L-2 B
Rangehood
Qasair Rangehoods Installation Instructions
36
13. 600HL-1 T / 700HL-1 T / 900HL-1 T 14. 600HL-1 T
15. CON 60L-1 T 16. CON 80L-1 T
17. CON 60L-1 T 18. CON 80L-2 T
CON 80L-2 T RangehoodCON 60L-1 T Rangehood
CON 60L-1 T Rangehood
CON 80L-1 T Rangehood
600HL-1 T Rangehood
600HL-1 T / 700HL-1 T / 900HL-1 T
Rangehood
Qasair Rangehoods Installation Instructions
37
19. 1200HL-2 T 20. LIS 800L-2 T
21. LIS 1000L-2 T 22. 3F 900L-2 T / 1200L-2 T
23. LIS 500L-1 T 24. LIS 800L-1 T
LIS 800L-2 T
Rangehood
1200HL-2 T
Rangehood
LIS 1000L-2 T
Rangehood
3F 900L-2 T / 1200L-2 T
Rangehood
LIS 800L-1 T
Rangehood
LIS 500L-1 T
Rangehood
Qasair Rangehoods Installation Instructions
38
25. CON 80L-1 T / LIS 1000-2 T 26. LIS 1200L-2 B
1. FA 60L-1 B2. FA 90L-1 T
FA-60L-1 B
Rangehood
FA-90L-1 T
Rangehood
LIS 1200L-2 B
Rangehood
LIS 1000L-2 T
Rangehood
CON 80L-1 T
Rangehood
Qasair Rangehoods Installation Instructions
39
FILTER CLEANING
OPERATION DETAILS
RANGEHOOD CLEANING
For the best results, please clean filters regularly.
Condari recommends cleaning filters once per month, or immediately after heavy use.
You can do this by hand washing in warm soapy water, or by placing filters in the top rack of the
dishwasher using a detergent of pH 8 or less.
Note: Washing the filters in the dishwasher may cause discolouration of the filters.
We recommend washing filters in the dishwasher without detergent or use one of the powder
detergent.
Ensure the filters are completely dry before placing them back.
Do not operate the rangehood without the filters installed.
Condari does not recommend the use of corrosive, caustic or acidic products, particulary industrial
or citric products.
Condari has experienced problems with many of the dishwashing detergents now on the market.
Particularly with the tablet type detergents as many come from overseas, which are made for a hard
water environment. We have found that these detergents have a deleterious effect on the filters and
the result is that the filters last for about 50 to 60 washes.
This is equivalent to about 5 to 6 years life.
Qasair rangehoods are made from stainless steel, either type 304 or type 316.
* Type 304 is classied as 18/8 stainless steel
* Type 316 is classied as 18/10 stainless steel
This means that the stainless steel is made of 18% nickel and either 8% or 10% of chromium respectively.
Stainless steel gets its protective coating from the chromium oxidising in the air to form a protective surface
of chromium oxide. This can be attacked by different substances, such as salt water or sea air. The stainless
steel will start to show pit marks which are referred to in the industry as tea staining. This will happen to
marine grade stainless steel type 316 in the same way it will happen to stainless steel type 304, it will just
take longer to happen.
The way to overcome this is to clean the stainless steel with warm soapy water and then polish it with a cloth
so that the chromium will oxidise again.
When exposed to sea water or sea side conditions this is only a stop gap measure as the attack will start
again.
With stainless steel rangehoods exposed in alfresco areas we recommend spraying the hood with vegetable
oil and rubbing it all over the rangehood, if it is going to be unused over a period of time.
Light ON and OFF
Fan Left Side ON and OFF
Right Side Fan/s ON and OFF
Light High and Low
Fan Left Side High and Low
Right Side Fan/s High and Low
Qasair Rangehoods Installation Instructions
40
CONDARI PTY LTD APPLIANCE GUARANTEE
The benefits conferred by this warranty are in addition to all other rights and remedies in respect of the product
which the consumer has under the Competition and Consumer Act 2010 and similar state and territory laws.
Condari in Melbourne (and by their agency in Country Areas and other States) warrants that the appliance will
be free from defects in materials and workmanship for a period of 36 months from the date of purchase of the
appliance to the consumer.
If there is a breach of this warranty, Condari will rectify, free of charge, at it’s nearest service centre or
authorised service agency any fault caused by faulty workmanship or material at the time of manufacture
occurring in the appliance within 36 months from the date of purchase of the appliance to the customer.
This warranty is conditional upon the appliance being used only for personal, domestic and household purposes
and installed and operated in accordance with Qasair instructions and does not apply to articles which by their
nature are consumable.
If a defect is caused by neglect, misuse, or failure to follow operating instructions where special precautions are
detailed for user attention then a charge shall be made for the service call.
For example:
With the filters the user is specifically requested:
• To clean filter regularly by handwashing or placing in a dishwasher at least once a month.
• To turn rangehood off after each use.
• Warranty under filter cleaning on page 39
Where a claim is made under warranty, Condari reserves the right to determine whether or not the fault is
caused by faulty workmanship or material or that the part is defective.
The consumer shall be fully responsible for all expenses whatsoever incidental to the removal of parts from
the unit or to their replacement. Amongst other things, such responsibility shall extend to damaged walls, tiles,
fixtures and fittings whether or not the unit has been built into a cupboard and irrespective of the stage either of
its installation or the fitting of any other item whatsoever in its vicinity.
No other person, or firm or corporation is authorised by Condari to offer or give on its behalf any other greater
warranty than that given by Condari under this warranty.
Condari provides to all Qasair rangehoods a 10 year motor replacement warranty. This is a change over
warranty.
The installation of the rangehood must comply with the information in this guide. Failure to follow the instructions
may result in loss of the warranty.
We do point out that incorrect installation such as the ducting being the incorrect size or the duct run being too
long will result in the motor failing and possible burning out.
The change over will be carried out by a authorised technician and will be charged at the rates applicable at
time of the change over.
Qasair Rangehoods Installation Instructions
41
EXCLUSIONS
There are some exclusions from the Condari Guarantee. (on previous page)
Qasair rangehoods are not to be used over barbecues approved for outdoor use only.
Condor rangehoods are designed to be used over all domestic barbecues available
in Australia.
For barbecues approved for outdoor use only we recommend the installation of a Condor rangehood. Condor
rangehoods are designed to move a greater volume of air to cope with the extra heat and smoke that a
barbecue will produce.
Qasair rangehoods are designed for use over all domestic cooking appliances with a megajoule rating up to
50mj. Qasair does manufacture rangehoods for high powered appliances that exceed this rating, please consult
with your Qasair representative to determine which rangehood is suited to your needs or whether a special
rangehood will need to be manufactured.
Condari will manufacture special rangehoods to go over commercial cooking appliances situated in domestic
kitchens.
Qasair Rangehoods Installation Instructions
42
STANDARD
WARRANTY
Date purchased:
Purchased from:
Model:
Serial No:
The purchaser must fill in the above information and keep this with the original purchase document.
This form must be produced if and when a claim is made under this warranty.
QASAIR Rangehoods are made in Ringwood, Australia.
Tel: +61 3 9482 7088
Fax: +61 3 9482 7011
Email: [email protected]
The Warranty is from the date of purchase and the service technician will need to see proof of purchase before,
we provides service under the guarantee.
If no proof of purchase can be provided, then the service call will be charged at standard rates, if proof is
provided later reimbursement will be made.
Qasair Rangehoods Installation Instructions
43
EXTENDED
WARRANTY
Customer Name:
Model Number: Serial Number:
Purchased from: Purchase Date:
Installer Name: Installed Date:
Installer Signature:
Installer is to confirm the following:
- Rangehood has been installed as per Qasair Instructions.
- All Ducting installed is as per Condari type and size.
- Ducting cross-sectional area has not been reduced along the length of the duct run.
- All Ducting joints have been appropriately sealed.
The installation warranty does not cover the ageing process in a building or any problems due to storm damage.
The Extended Warranty is from the date of purchase and the service technician will need to see proof of
purchase before, we provides service under the guarantee.
If no proof of purchase can be provided, then the service call will be charged at standard rates, if proof is
provided later reimbursement will be made.
Condari provides an extended warranty from 36 months to 72 months if installed by an authorised Qasair
installer and the below form is completed.
The authorised installer also offers a warranty on their workmanship for the same period of 72 months with a
guarantee that the installation is in compliance with ‘Qasair installation instructions’.
Qasair Rangehoods Installation Instructions
44
NOTES
Qasair Rangehoods Installation Instructions
45
NOTES
Qasair Rangehoods Installation Instructions
46
NOTES
NOTES
DISTRIBUTED IN AUSTRALIA BY CONDARI PTY LTD
Tel: 1300 360 563
HEAD OFFICE
VIC Tel: 03 9482 7088 Fax: 03 9482 7011
Email: [email protected]
Website: www.condari.com.au
YOUR DISTRIBUTORS
QLD Tel: 07 3423 3503 Fax: 07 3282 9122 Email: [email protected]
TAS Tel: 03 9482 7088 Fax: 03 9482 7011 Email: [email protected]
New Zealand
Singapore
QASAIR RANGEHOODS MADE IN RINGWOOD 3134
CONDARI RESERVES THE RIGHT TO CHANGE SPECIFICATION WITHOUT NOTICE
rev. 170323
www.condari.com.au
