Loading ...
Loading ...
Loading ...
29
Battery
This equipment is not suitable for use in locations where
children are likely to be present.
CAUTION: Risk of explosion if the battery is replaced by an
incorrect type.
Improper replacement of the battery with an incorrect type
may defeat a safeguard (for example, in the case of some
lithium battery types).
Do not dispose of the battery into fire or a hot oven, or
mechanically crush or cut the battery, which may result in an
explosion.
Do not leave the battery in an extremely high temperature
surrounding environment, which may result in an explosion
or the leakage of flammable liquid or gas.
Do not subject the battery to extremely low air pressure,
which may result in an explosion or the leakage of flammable
liquid or gas.
Dispose of used batteries according to the instructions.
For Device with Laser
LASER RADIATION
DO NOT STARE INTO BEAM
CLASS 2 LASER PRODUCT
Cautions
Fire Prevention
No naked flame sources, such as lighted candles, should be
placed on the equipment.
The serial port of the equipment is used for debugging only.
Hot Surface
CAUTION: Hot parts! Burned fingers when handling the parts.
This sticker is to indicate that the
marked item can be hot and should
not be touched without taking care.
Wait one-half hour after switching
off before handling parts.
The device with this sticker is intended for installation in a
restricted access location. Access can only be gained by
service persons or by users who have been instructed about
the reasons for the restrictions applied to the location and
about any precautions that shall be taken.
Installation
Install the equipment according to the instructions in this
manual.
To prevent injury, this equipment must be securely attached
to the ceiling/wall in accordance with the installation
instructions.
Be sure that there is enough space to install the device and
accessories.
Make sure that the wall is strong enough to withstand at least
8 times the weight of the device and the mount.
Make sure that the power has been disconnected before you
wire, install, or disassemble the device.
Transportation
Keep the device in original or similar packaging while
transporting it.
Do not drop the product or subject it to physical shock.
Power Supply
The power source should meet limited power source or PS2
requirements according to IEC 60950-1 or IEC 62368-1
standard.
Refer to the device label for the standard power supply.
Please make sure your power supply matches with your
device.
Use a power adapter provided by qualified manufacturers. It
is recommended to provide an independent power adapter
for each device as adapter overload may cause over-heating
or a fire hazard.
System Security
Please understand that you have the responsibility to
configure all the passwords and other security settings about
the device, and keep your user name and password.
Maintenance
If the product does not work properly, please contact your
dealer or the nearest service center. We shall not assume any
responsibility for problems caused by unauthorized repair or
maintenance.
A few device components (e.g., electrolytic capacitor) require
regular replacement. The average lifespan varies, so periodic
checking is recommended. Contact your dealer for details.
Cleaning
Please use a soft and dry cloth to clean the interior and
exterior surfaces. Do not use alkaline detergents.
Using Environment
When any laser equipment is in use, make sure that the
device lens is not exposed to the laser beam, or it may burn
out.
Do not aim the lens at the sun or any other bright light.
To avoid heat accumulation, good ventilation is required for a
proper operating environment.
DO NOT expose the device to extremely hot, cold, dusty,
corrosive, saline-alkali, or damp environments. For
temperature and humidity requirements, see device
specification.
DO NOT expose the device to high electromagnetic radiation.
Illuminator
Make sure that there is no reflective surface too close to the
camera lens. The IR light from the camera may reflect back
into the lens causing reflection.
The beam of the light at the distance of 200 mm is classified
as Risk Group 1 (RG1). Possible hazardous optical radiation
emitted from this product. Do NOT stare at operating light
source. May be harmful to the eyes.
If appropriate shielding or eye protection is not available, turn
on the light only at a safe distance or in the area that is not
directly exposed to the light when installing or maintaining
the device.
Emergency
If smoke, odor, or noise arises from the device, immediately
turn off the power, unplug the power cable, and contact the
service center.
Time Synchronization
Set up device time manually for the first time access if the
local time is not synchronized with that of the network. Visit
the device via web browser/client software and go to time
settings interface.
Français
L’image du produit est donnée uniquement à titre de
référence et le produit réel peut présenter un aspect
différent.
Interface :
① Logement pour carte mémoire
② Interface réseau
③ Interface BNC
④ Interface RS-485
⑤ Interface d’alimentation
⑥ Interface audio
⑦ Sortie d’alarme
⑧ Entrée d’alarme
⑨ Interface fibre optique
⑩ Bouton de réinitialisation : Appuyez sur le bouton de
réinitialisation pendant environ 10 s lors de la mise en
marche ou du redémarrage de la caméra pour restaurer
les paramètres par défaut, notamment le nom
d’utilisateur, le mot de passe, l’adresse IP, le numéro de
port, etc.
Loading ...
Loading ...
Loading ...