Home
Bookmarks
Home
Pelco
Pelco PA101-AW User Manual
Pelco PA101-AW Pole Mount Adapter
Pelco PA/SPA Series Pole Mount Adapters - Installation Guide
For PA101-AW.
PDF File Manual
,
4 pages
,
Read Online
|
Download pdf file
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Only use attachments/accessories specified by the manufacturer.
6. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
7. Installation should be done only by qualified personnel and conform to all local codes.
8. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is designed for indoor use only and it must not be installed where exposed to rain and moisture.
9. Use only installation methods and materials capable of supporting four times the maximum specified load.
10. Use stainless steel hardware to fasten the mount to outdoor surfaces.
11. CAUTION: These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other than contained in the operating instructions unless you are qualified to do so.
Description
Models
Installation
1. Position the pole mount adapter on the pole and attach it to the pole with the stainless steel straps provided. Tighten the strap screws securely.
2. Attach your mount to the pole mount adapter with the provided nuts and washers and securely tighten.
3. If you are using the WM2000 wall mount and require an ST1 support strut for additional support, install an SPA102 pole mount adapter. Measure 14 inches (36 cm) down from the bottom of the WM2000 and mark the pole. Center the SPA102 on the pole at ...
Figure 1. Typical Pole Mount Adapter Installation
Specifications
Page 1/4
Page 1
Page 2
Page 3
Page 4
Contents
Table of Contents
Search
Previous
Next
Bookmarks
PA100/PA101/PA101
-AW/
PA101-SW/PA102/
SPA102
Pole
Mount
Adapters
INSTALLATION
C250M-H (03/21)
Loading ...
Loading ...
Loading ...
File type: PDF
File name: 2569_pa101-aw.pdf
File size: 326.41 KB
File Language: English
Pages: 4
Author: Pelco
File created: 2017-12-07
Published:
2024-05-09
Updated: 2024-05-09
Download File
Other documents for Pelco PA101-AW
The following documents are available:
Installation Instruction
Pelco PA/SPA Series Pole Mount Adapters - Installation Guide - (English)
Read Online
|
Download pdf
Photos
Photos:
View Photos
Specifications
Brand:
Pelco
Model: PA101-AW
Category:
Charger & Adapter
View in the file:
Full Specifications
See other models:
PA101
IBE832-1ER
IBE839-1ER
IBE539-1ER
IME832-1ERS
Related Products
Pelco PA101
Pelco SRXV-PLM
Pelco IMV-PA
Pelco IMV-AP
Pelco IBV-A4S
Pelco IJTV-AP
Pelco IMD1-PMT
Pelco IMD1-SMT
Pelco IMD1-INC
Hikvision DS-1603ZJ-POLE-P
I-Pro WV-Q188
I-Pro WV-Q182
Pelco EPP2
Pelco EPM
Pelco ECM100
Table of Contents
×
Important Safety Instructions
2
1. Read these instructions.
2
2. Keep these instructions.
2
3. Heed all warnings.
2
4. Follow all instructions.
2
5. Only use attachments/accessories specified by the manufacturer.
2
6. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
2
7. Installation should be done only by qualified personnel and conform to all local codes.
2
8. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is designed for indoor use only and it must not be installed where exposed to rain and moisture.
2
9. Use only installation methods and materials capable of supporting four times the maximum specified load.
2
10. Use stainless steel hardware to fasten the mount to outdoor surfaces.
2
11. CAUTION: These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other than contained in the operating instructions unless you are qualified to do so.
2
Description
2
Models
2
Installation
3
1. Position the pole mount adapter on the pole and attach it to the pole with the stainless steel straps provided. Tighten the strap screws securely.
3
2. Attach your mount to the pole mount adapter with the provided nuts and washers and securely tighten.
3
3. If you are using the WM2000 wall mount and require an ST1 support strut for additional support, install an SPA102 pole mount adapter. Measure 14 inches (36 cm) down from the bottom of the WM2000 and mark the pole. Center the SPA102 on the pole at ...
3
Figure 1. Typical Pole Mount Adapter Installation
3
Specifications
3
Search:
×
Search
