Loading ...
Loading ...
Loading ...
4
OPERATION
WARNING
To reduce the risk of injury, wear
safety goggles or glasses with side
shields.
Using the Control Switch
The control switch may be set to three positions:
forward, reverse and lock. Due to a lockout mecha-
nism, the control switch can only be adjusted when
the ON/OFF switch is not pressed. Always allow the
motor to come to a complete stop before using the
control switch.
For forward (clockwise) rotation,
CENTER TO LOCK
Forward
Reverse
push the control switch in the
direction shown. Check the di-
rection of rotation before use.
For reverse (counterclockwise)
rotation, push the control switch
in the direction shown. Check the
direction of rotation before use.
To lock the trigger, push the control switch to the
center position. The trigger will not work when the
control switch is in the locked position.
Always remove the battery pack before performing
maintenance, changing accessories, storing the tool
and any time the tool is not in use.
Selecting Mode
Allow the tool to come to a complete stop before
changing modes. Press the selector button
to
cycle between the settings.Select wireless
to
change the default settings via the ONE-KEY App
on your smart device.
Default Max RPM
Setting 1 Setting 2 Setting 3 Setting 4
2757-20 850 1 500 2 100 3 000
2758-20
2759-20
2759B-20
900 1 400 1 900 2 500
Starting, Stopping and Controlling Speed
These tools may be operated at any speed from 0
to full speed.
1. To start the tool, pull the trigger.
NOTE: An LED is turned on when the trigger is
pulled.
2. To vary the driving speed, increase or decrease
pressure on the trigger. The further the trigger is
pulled, the greater the speed, up to the maximum
speed set by the speed control.
3. To stop the tool, release the trigger and the electric
brake stops the tool instantly.
Impacting Techniques
The longer a bolt, screw, or nut is impacted, the
tighter it will become. To help prevent damaging the
fasteners or workpieces, avoid excessive impact-
ing. Be particularly careful when impacting smaller
fasteners because they require less impacting to
reach optimum torque.
Practice with various fasteners, noting the length of
time required to reach the desired torque. Check the
tightness with a hand-torque wrench. If the fasteners
are too tight, reduce the impacting time. If they are
not tight enough, increase the impacting time.
Oil, dirt, rust or other matter on the threads or under
the head of the fastener affects the degree of tight-
ness.
ASSEMBLY
WARNING
Recharge only with the charger
specied for the battery. For spe-
cic charging instructions, read the operator’s
manual supplied with your charger and battery.
Removing/Inserting the Battery
To remove the battery, push in the release buttons
and pull the battery pack away from the tool.
WARNING
Always remove battery pack before
changing or removing accessories.
To insert the battery, slide the pack into the body
of the tool. Make sure it latches securely into place.
WARNING
Only use accessories specically
recommended for this tool. Others
may be hazardous.
Use only sockets and other accessories speci-
cally designed for use on impact wrenches and
drivers. Other sockets and accessories might
shatter or break causing injury.
Attaching and Removing Accessories
1/4" Hex Impact Driver (Cat. No. 2757-20)
This impact driver is intended for use with
drill and driver bits.
1. To attach an accessory, press the shank
into the hex drive chuck.
2. To remove the accessory, pull out the
ring and remove the accessory. Re-
lease the ring.
Square Drive Impact Wrenches
(Cat. No. 2758-20, 2759B-20)
1. Use only the appropriate size Square
Drive Sockets.
2. To attach a socket, align the accessory with the
anvil and push it rmly over the retaining ring.
3. To remove the accessory, pull the accessory off
the anvil.
Square Drive Impact Wrench with Pin Detent
(Cat. No. 2759-20)
1. Use only the appropriate size Square Drive
Sockets.
2. To attach a socket, align the hole in the accessory
with the detent pin on the anvil. Hold the detent
pin in while pushing the socket onto the anvil.
The detent pin will snap into place in the hole to
secure the socket.
3. To remove the socket, insert a nail or other thin
object into the hole in the accessory and press
in the detent pin. Pull the accessory off the anvil.
ONE-KEY™
To learn more about the ONE-KEY functionality for
this tool, please reference the Quick Start guide in-
cluded with this product or go to milwaukeetool.com/
One-Key. To download the ONE-KEY app, visit the
App Store or Google Play from your smart device.
Loading ...
Loading ...
Loading ...