User Manual FLUKE 9100S-B-156 Dry Block Calibrator with block B, 95 to 707°F

Documents for FLUKE 9100S-B-156

User Manual for the Fluke 9100S-B-156 Dry Block Calibrator with block B, 95 to 707°F

For 9100S-B-156.

• Table of Contents3
• 1 Before You Start8
  • 1.1 Introduction8
  • 1.2 Symbols Used8
  • 1.3 Safety Information10
    • 1.3.1 Warnings10
    • 1.3.2 Cautions11
  • 1.4 Authorized Service Centers12
• 2 Specifications and Environmental Conditions13
  • 2.1 Specifications13
  • 2.2 Environmental Conditions13
• 3 Quick Start14
  • 3.1 Unpacking14
  • 3.2 Set-up14
  • 3.3 Power14
  • 3.4 Setting the Temperature14
• 4 Parts and Controls16
  • 4.1 Rear Panel16
  • 4.2 Side View17
  • 4.3 Front Panel18
  • 4.4 Constant Temperature Block Assembly18
• 5 General Operation20
  • 5.1 Setting the Temperature20
  • 5.2 Changing Display Units20
• 6 Controller Operation21
  • 6.1 Well Temperature21
  • 6.2 Temperature Set-point21
    • 6.2.1 Programmable Set-points21
    • 6.2.2 Set-point Value22
    • 6.2.3 Temperature Scale Units22
  • 6.3 Scan22
    • 6.3.1 Scan Control24
    • 6.3.2 Scan Rate24
  • 6.4 Set-point Resistance24
  • 6.5 Secondary Menu25
  • 6.6 Heater Power25
  • 6.7 Proportional Band25
  • 6.8 Controller Configuration26
  • 6.9 Operating Parameters27
  • 6.10 High Limit27
  • 6.11 Serial Interface Parameters27
    • 6.11.1 Baud Rate27
    • 6.11.2 Sample Period28
    • 6.11.3 Duplex Mode28
    • 6.11.4 Linefeed29
  • 6.12 Calibration Parameters29
    • 6.12.1 Hard Cutout30
    • 6.12.2 R030
    • 6.12.3 ALPHA30
    • 6.12.4 DELTA31
• 7 Digital Communication Interface32
  • 7.1 RS-232 Connection32
  • 7.2 Interface Commands33
• 8 Test Probe Calibration35
  • 8.1 Calibrating a Single Probe35
  • 8.2 Dry-well Characteristics35
    • 8.2.1 Stabilization and Accuracy35
• 9 Calibration Procedure36
  • 9.1 Calibration Points36
  • 9.2 Calibration Procedure36
    • 9.2.1 Compute DELTA37
    • 9.2.2 Compute R0 and ALPHA37
    • 9.2.3 Accuracy and Repeatability38
• 10 Maintenance39
• 11 Troubleshooting40
  • 11.1 Troubleshooting Problems, Possible Causes, and Solutions40
  • 11.2 CE Comments41
    • 11.2.1 EMC Directive41
    • 11.2.2 Low Voltage Directive (Safety)41
• Tables6
  • Table 1 International Electrical Symbols8
  • Table 2 Controller communications commands33
• Figures7
  • Figure 1 Back Panel16
  • Figure 2 Side view of the 9100S showing the prop stand17
  • Figure 3 Front panel18
  • Figure 4 Fixed block options19
  • Figure 5 Controller operation flow chart23
  • Figure 6 Serial cable wiring32