1. Home
  2. Mr. Heater
  3. Mr. Heater MH15TS User Manual
  4. Page 3

User Manual - Page 3

For MH15TS.

Loading ...
Loading ...
OperatingInstructionsandOwner’sManualMr.Heater|Gas-FiredInfra-RedTankTopHeater
3
ASSEMBLY AND HOOK-UP INFORMATION
1. HeatermodelMH15TSandMH30TSarepackaged
complete.Propanecylinders(tanks)arenotincluded
withheatermodel.
2. Removeheaterfromcarton.
3. UseonlyvaporwithdrawalLPgascylindersconstructed
forusewithpropaneonly(HD-5)andmarkedinaccor-
dancewiththespecificationsforLPgascylindersofthe
U.S.DepartmentofTransportation(DOTSPEC.39).
4. Thisheatermustbeusedonlywithavaporwithdrawal
LPgasbulktankequippedwithastandardPOLvalve
–donotusethisheateronbulktanksgreaterthan20
poundsLPGcapacity(50poundswatercapacity).
5a. MH30TS Dual Burner Model (see Figure 1.)
• Thetankcollarbracketmustbeassembledbefore
theheatercanbeattachedtothepropanetank.
• RemovescrewsholdingPiezoIgniterbracketto
manifoldcenterplateandretainforlateruse.
• Alignboltholesintankcollarbracketwithbolt
holesincenterplateonmanifoldsuchthatthe
heaterisfacingoutwardonceattachedtocylinder
collar.
• Attachedwithscrewsremovedabove,makingsure
thatPiezoIgniterbracketisbetweentankcollar
bracketandmanifoldcenterplate.
• Placeheaterontotankwithtankcollarbracket
overtankcollar.Mountingboltknobshouldbe
positionedtotheoutsideoftankcollar.
• Firmlysecuretotankbyhand-tighteningmounting
boltknob.Donotovertighten.
• Makesureheaterregulatorisinthe“OFF”position.
• Insertregulator’sconnectorintotank’svalveand
turnleft(counterclock-wise)withhandasmuchas
possible.Donotovertighten.
5b. MH15TS Single Burner Model (See Figure 2.)
• Besureheaterisfacingawayfromtank.
• Insertregulatorconnectorintotankvalveoutlet
fittingandturnleft(counterclock-wise)untilfully
tightened.Donotovertighten.(SeeFigure2a)
• Placeheatersupportaroundventuriandslideclip
endsontopropanecylindercollar.Use1/4”-20x
35mmscrewandwingnuttosecureheatersup-
portontoventuritube.(SeeFigure2b)
Figure2a.
6. Operateonlyonastable,levelsurface.
7. Openpropanetankvalveslowly.
8. Checkallfittingsforleaks.Applya50/50mixtureof
liquidsoapandwatertoalljoints.Bubblesforming
indicatealeakingconnection.Correctallleaksbefore
proceeding.
WARNING
Nevertouchheaterwhileinoperationtoavoidinjury.
Moveheaterbygraspingthepropanecylindercarefully.
9. Theheatershouldbeinspectedbeforeeachuseandat
leastannuallybyaqualifiedserviceperson.
10.Thehoseassemblyshallbevisuallyinspectedpriorto
useofheater.Ifitisevidentthereisexcessiveabrasion
orwear,orthehoseiscut,itmustbereplacedpriorto
theheaterbeingputintooperation.Replacementhose
assemblyshallbeMr.Heaterhoseassemblyaslistedin
thepartslist.
11. Minimuminletgaspressureis20psi.
12. Maximuminletgaspressureis120psi(equivalentto
anambienttemperatureof75°F(24°C)).
Figure2b.
Figure1.
Loading ...
Loading ...
Loading ...