ninjakitchen.com
BLAST™ PORTABLE BLENDER
BC100/BC150 Series | Owner’s Guide
1 Read all instructions prior to using the appliance and its accessories.
2 Carefully observe and follow all warnings and instructions. This unit contains electrical connections and moving parts that potentially present
risk to the user.
3 ALWAYS exercise care when handling the BlastBlade™ Assembly. The blades are sharp, handle carefully. ONLY grasp the BlastBlade™ Assembly
by the motor base. Failure to use care when handling the BlastBlade™ Assembly will result in a risk of laceration.
4 Take your time and exercise care during unpacking and appliance setup. This appliance contains sharp, loose blades that can cause injury
if mishandled.
5 Take inventory of all contents to ensure you have all parts needed to properly and safely operate your appliance.
6 DO NOT blend hot liquids or carbonated liquids, as doing so may cause pressure buildup, resulting in risk of burns or other injuries to the user.
7 DO NOT fill the blending vessel past the MAX FILL line.
8 Blades are sharp. Handle carefully.
9 Before use, wash all parts that may contact food. Follow washing instructions covered in this Owner's Guide.
10 To protect against the risk of fire from battery damage, DO NOT submerge the motor base in any form of liquid.
11 DO NOT store outdoors or allow the product to be submerged in liquid.
12 DO NOT allow children to operate this appliance or use as a toy. Close supervision is necessary when any appliance is used near children.
13 This appliance is NOT intended to be used by people with reduced physical, sensory, or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
14 Before each use, inspect BlastBlade™ Assembly for damage. If a blade is bent or damage is suspected, contact SharkNinja to arrange
for replacement.
WARNING: To reduce the risk of injury, fire, electrical shock or property damage, basic safety precautions must always be followed,
including the following numbered warnings and subsequent instructions. Do not use appliance for other than intended use.
WARNING: Handle the BlastBlade™ Assembly with care, as the blades are sharp.
WARNING: Remove utensils prior to processing. Failure to remove may cause the blending vessel to be damaged or to shatter, which may
cause personal injury.
WARNING: DO NOT blend hot, eervescent, or carbonated liquids. Doing so may cause excessive pressure buildup, resulting in risk
of laceration and/or the user being burned.
WARNING: DO NOT put your hands inside the vessel or anywhere near the BlastBlade™ Assembly. Blades can still activate when the
sip lid is removed.
IMPORTANT SAFETY INSTRUCTIONS
PLEASE READ ALL INSTRUCTIONS BEFORE USE • FOR HOUSEHOLD USE ONLY
Read and review instructions for operation and use.
Indicates the presence of a hazard that can cause personal injury, death or substantial property damage if
the warning included with this symbol is ignored.
For household use only.
Indicates location to attach USB-C cord for charging unit.
When using electrical appliances, basic safety precautions should always be followed, including the following:
ninjakitchen.com
ninjakitchen.com
15 DO NOT attempt to sharpen blades.
16 DO NOT allow any part of the unit to contact hot surfaces, including stoves and other heating appliances.
17 ALWAYS use the appliance on a dry and level surface.
18 Keep hands, hair, and clothing out of the vessel when loading and operating.
19 ONLY use attachments and accessories that are provided with the product or are recommended by SharkNinja. The use of attachments not
recommended or sold by SharkNinja may cause fire, electric shock, or injury.
20 During operation and handling of the appliance, avoid contact with moving parts.
21 DO NOT operate the appliance with an empty container.
22 DO NOT microwave any containers or accessories provided with the appliance.
23 DO NOT perform grinding operations.
24 Before operation, ensure all utensils are removed from containers. Failure to remove utensils can cause the vessel to shatter and potentially
result in personal injury and property damage.
25 DO NOT attempt to defeat the interlock mechanism. Ensure the vessel and sip lid are properly installed before operation.
26 DO NOT expose the containers and accessories to extreme temperature changes. They may experience damage.
27 NEVER leave the appliance unattended while in use.
28 If you find unmixed ingredients sticking to the sides of the cup, turn o the appliance using the Power Button, and use a scraper to
dislodge ingredients.
29 DO NOT attempt to remove the vessel and/or sip lid from the motor base while the BlastBlade™ Assembly is still spinning. Allow the appliance
to come to a complete stop before removing lid and/or vessel.
30 DO NOT store ingredients for extended amounts of time before or after blending them. Some foods may contain active ingredients or release
gases that will expand if left in a sealed container, resulting in excessive pressure buildup that can pose a risk of injury.
31 If the appliance overheats, a thermal switch will activate and temporarily disable the motor. To reset, turn OFF the Ninja Blast™ Portable Blender
using the Power Button and allow it to cool for approximately 15 minutes before using again.
32 DO NOT process dry ingredients without adding liquid to the blending vessel. Unit is not intended for dry blending.
33 Operate ONLY with the sip lid on.
34 DO NOT refrigerate or freeze blender.
SAVE THESE INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
PLEASE READ ALL INSTRUCTIONS BEFORE USE • FOR HOUSEHOLD USE ONLY
BATTERY USE
1 The battery is the power source for the Ninja Blast™ Portable Blender. Carefully read and follow all charging instructions.
2 DO NOT incinerate this appliance even if it is severely damaged. The lithium-ion batteries can explode in a fire. Always properly recycle
products powered by lithium-ion batteries.
3 Since there is no power cord, prevent accidental blade activation by ensuring the blender is turned OFF when not in use, while cleaning,
or when drinking from the sip lid.
4 Keep the battery away from all metal objects such as paper clips, coins, keys, nails, or screws. Shorting the battery terminals together
increases the risk of fire or burns.
5 Under abusive conditions, liquid may be ejected from the battery. Avoid contact with this liquid, as it may cause irritation or burns. If contact
occurs, flush with water. If liquid contacts eyes, seek medical help.
PARTS
A Sip Lid
B Carry Handle
C Blending Vessel*
D Vessel Cap*
E Blade Cover*
F Motor Base with
BlastBlade™ Assembly
G USB-C Charging Cord
H Charging Port
Remove all packaging materials from the unit. Exercise care when unpacking BlastBlade™ Assembly,
as the blade are sharp.
Wash vessel, lid, and BlastBlade™ Assembly in warm, soapy water using a dishwashing utensil with
a handle to avoid direct contact with the blades. DO NOT submerge the motor base in water when
cleaning. Exercise care when handling BlastBlade™ Assembly, as the blades are sharp.
Thoroughly rinse and air-dry all appropriate parts.
Charge the unit for at least 2 hours for a full battery. LEDs will illuminate GREEN when fully charged.
Charging port is located at the back of the motor base. Use provided USB-C charging cord with a
5V 3A power supply.
BEFORE FIRST USE
IMPORTANT: Review all warnings at the beginning of this Owner’s Guide before proceeding.
NOTES:
• Handle the BlastBlade™ Assembly by grasping around the motor base.
• All attachments are BPA free. All attachments EXCEPT the motor base are top-rack dishwasher
safe. DO NOT use a heated dry cycle. Ensure lid and vessel are removed from motor base before
placing in the dishwasher. Exercise care when handling BlastBlade™ Assembly.
B
A
F
H
C
D
E
* Blending vessel sizes and quantity,
and accessories vary by model.
Motor Base Back
G
CHARGING
ninjakitchen.com
ninjakitchen.com
15 DO NOT attempt to sharpen blades.
16 DO NOT allow any part of the unit to contact hot surfaces, including stoves and other heating appliances.
17 ALWAYS use the appliance on a dry and level surface.
18 Keep hands, hair, and clothing out of the vessel when loading and operating.
19 ONLY use attachments and accessories that are provided with the product or are recommended by SharkNinja. The use of attachments not
recommended or sold by SharkNinja may cause fire, electric shock, or injury.
20 During operation and handling of the appliance, avoid contact with moving parts.
21 DO NOT operate the appliance with an empty container.
22 DO NOT microwave any containers or accessories provided with the appliance.
23 DO NOT perform grinding operations.
24 Before operation, ensure all utensils are removed from containers. Failure to remove utensils can cause the vessel to shatter and potentially
result in personal injury and property damage.
25 DO NOT attempt to defeat the interlock mechanism. Ensure the vessel and sip lid are properly installed before operation.
26 DO NOT expose the containers and accessories to extreme temperature changes. They may experience damage.
27 NEVER leave the appliance unattended while in use.
28 If you find unmixed ingredients sticking to the sides of the cup, turn o the appliance using the Power Button, and use a scraper to
dislodge ingredients.
29 DO NOT attempt to remove the vessel and/or sip lid from the motor base while the BlastBlade™ Assembly is still spinning. Allow the appliance
to come to a complete stop before removing lid and/or vessel.
30 DO NOT store ingredients for extended amounts of time before or after blending them. Some foods may contain active ingredients or release
gases that will expand if left in a sealed container, resulting in excessive pressure buildup that can pose a risk of injury.
31 If the appliance overheats, a thermal switch will activate and temporarily disable the motor. To reset, turn OFF the Ninja Blast™ Portable Blender
using the Power Button and allow it to cool for approximately 15 minutes before using again.
32 DO NOT process dry ingredients without adding liquid to the blending vessel. Unit is not intended for dry blending.
33 Operate ONLY with the sip lid on.
34 DO NOT refrigerate or freeze blender.
SAVE THESE INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
PLEASE READ ALL INSTRUCTIONS BEFORE USE • FOR HOUSEHOLD USE ONLY
BATTERY USE
1 The battery is the power source for the Ninja Blast™ Portable Blender. Carefully read and follow all charging instructions.
2 DO NOT incinerate this appliance even if it is severely damaged. The lithium-ion batteries can explode in a fire. Always properly recycle
products powered by lithium-ion batteries.
3 Since there is no power cord, prevent accidental blade activation by ensuring the blender is turned OFF when not in use, while cleaning,
or when drinking from the sip lid.
4 Keep the battery away from all metal objects such as paper clips, coins, keys, nails, or screws. Shorting the battery terminals together
increases the risk of fire or burns.
5 Under abusive conditions, liquid may be ejected from the battery. Avoid contact with this liquid, as it may cause irritation or burns. If contact
occurs, flush with water. If liquid contacts eyes, seek medical help.
PARTS
A Sip Lid
B Carry Handle
C Blending Vessel*
D Vessel Cap*
E Blade Cover*
F Motor Base with
BlastBlade™ Assembly
G USB-C Charging Cord
H Charging Port
Remove all packaging materials from the unit. Exercise care when unpacking BlastBlade™ Assembly,
as the blade are sharp.
Wash vessel, lid, and BlastBlade™ Assembly in warm, soapy water using a dishwashing utensil with
a handle to avoid direct contact with the blades. DO NOT submerge the motor base in water when
cleaning. Exercise care when handling BlastBlade™ Assembly, as the blades are sharp.
Thoroughly rinse and air-dry all appropriate parts.
Charge the unit for at least 2 hours for a full battery. LEDs will illuminate GREEN when fully charged.
Charging port is located at the back of the motor base. Use provided USB-C charging cord with a
5V 3A power supply.
BEFORE FIRST USE
IMPORTANT: Review all warnings at the beginning of this Owner’s Guide before proceeding.
NOTES:
• Handle the BlastBlade™ Assembly by grasping around the motor base.
• All attachments are BPA free. All attachments EXCEPT the motor base are top-rack dishwasher
safe. DO NOT use a heated dry cycle. Ensure lid and vessel are removed from motor base before
placing in the dishwasher. Exercise care when handling BlastBlade™ Assembly.
B
A
F
H
C
D
E
* Blending vessel sizes and quantity,
and accessories vary by model.
Motor Base Back
G
CHARGING
ninjakitchen.com
ninjakitchen.com
USING THE CONTROL PANEL
PROGRAMS:
START/STOP BUTTON
Press Start/Stop button once to activate the 30-second blend cycle.
POWER BUTTON
Press Power button to turn unit ON and OFF.
TROUBLESHOOTING LED Shows Solutions
Vessel and Base are Not Aligned Flashing WHITE
Ensure vessel and motor base are
aligned using the arrows on the back
of motor base and vessel.
Blades are Blocked Flashing ORANGE
Move lodged ingredients from blade
& restart blend program.
Needs Charge Solid RED Charge unit.
Abnormal charger Flashing RED and BLUE
Defective charger, unplug & find correct
5V 3A charger.
Unit Cool Down Time Out Clockwise-moving ORANGE LEDs
Let unit sit at room temp for 15 minutes
before using again.
While Charging Flashing WHITE and RED Call Customer Service.
While Blending
Flashing RED in the bottom left
and top right
Call Customer Service.
USING THE BLENDING VESSEL
IMPORTANT: Review all warnings at the beginning of this Owner’s Guide before proceeding.
1 Ensure the motor base is fully charged and the vessel is properly installed
by aligning vessel arrow with motor base arrow located on the back of the
motor base.
2 Turn unit ON by pressing the
button until Start/Stop button
lights illuminate.
3 Add ingredients, starting with liquids then solid ingredients. If using ice,
always add last. DO NOT fill ingredients past the MAX FILL line. Secure
lid onto the vessel, twisting clockwise to tighten.
4 Blend for a 30-second blend cycle by pressing the Start/Stop button.
5 Open the sip lid to sip, or remove the lid to pour out blender outputs
into another container. DO NOT remove vessel from motor base when
filled. Empty vessel prior to removing from motor base.
6 After blending, power OFF the unit by pressing the
button.
Motor base should be turned OFF when drinking from the sip lid
and when blender is no longer in use.
7 Refer to the Care & Maintenance section for cleaning and
storage instructions.
CARE & MAINTENANCE
CLEANING
Blades can still operate when the lid is removed. Always turn the unit OFF when cleaning without the lid on
or when the BlastBlade™ Assembly is exposed.
Hand-Washing
Wash vessel, lid, and BlastBlade™ Assembly with warm, soapy water. Use a dishwashing utensil or cloth
to clean the BlastBlade™ Assembly on the motor base. Exercise care when handling the BlastBlade™
Assembly on the motor base as the blades are sharp. Wipe the motor base with a clean, damp cloth.
DO NOT submerge the motor base in water. Thoroughly rinse and air-dry all appropriate parts.
Motor Base
The USB-C port and the Motor Base are is water resistant, which means the motor base can get rinsed
in the sink; HOWEVER DO NOT put the motor base in the dishwasher or submerge it in water. Ensure the
USB-C charger is not inserted before cleaning.
DEEPER CLEAN
Dishwasher
Vessel and sip lid are top-rack dishwasher safe. DO NOT use a heated dry cycle. Ensure the vessel
and sip lid are removed from the motor base before being placed in the dishwasher.
STORING
Store the unit upright and with the lid, vessel, and motor base fully assembled.
DO NOT store blended or unblended ingredients in the vessel with the BlastBlade™ Assembly
for prolonged periods of time.
DO NOT stack items on top of the vessel. Store any remaining attachments alongside the unit
or in a cabinet where they will not be damaged or create a hazard.
If your unit needs servicing, call Customer Service at 1-877-646-5288. So we may better assist you, please
register your product online at registeryourninja.com and have the product on hand when you call.
ORDERING REPLACEMENT PARTS
To order additional parts and attachments, visit ninjaaccessories.com.
ninjakitchen.com
ninjakitchen.com
USING THE CONTROL PANEL
PROGRAMS:
START/STOP BUTTON
Press Start/Stop button once to activate the 30-second blend cycle.
POWER BUTTON
Press Power button to turn unit ON and OFF.
TROUBLESHOOTING LED Shows Solutions
Vessel and Base are Not Aligned Flashing WHITE
Ensure vessel and motor base are
aligned using the arrows on the back
of motor base and vessel.
Blades are Blocked Flashing ORANGE
Move lodged ingredients from blade
& restart blend program.
Needs Charge Solid RED Charge unit.
Abnormal charger Flashing RED and BLUE
Defective charger, unplug & find correct
5V 3A charger.
Unit Cool Down Time Out Clockwise-moving ORANGE LEDs
Let unit sit at room temp for 15 minutes
before using again.
While Charging Flashing WHITE and RED Call Customer Service.
While Blending
Flashing RED in the bottom left
and top right
Call Customer Service.
USING THE BLENDING VESSEL
IMPORTANT: Review all warnings at the beginning of this Owner’s Guide before proceeding.
1 Ensure the motor base is fully charged and the vessel is properly installed
by aligning vessel arrow with motor base arrow located on the back of the
motor base.
2 Turn unit ON by pressing the
button until Start/Stop button
lights illuminate.
3 Add ingredients, starting with liquids then solid ingredients. If using ice,
always add last. DO NOT fill ingredients past the MAX FILL line. Secure
lid onto the vessel, twisting clockwise to tighten.
4 Blend for a 30-second blend cycle by pressing the Start/Stop button.
5 Open the sip lid to sip, or remove the lid to pour out blender outputs
into another container. DO NOT remove vessel from motor base when
filled. Empty vessel prior to removing from motor base.
6 After blending, power OFF the unit by pressing the
button.
Motor base should be turned OFF when drinking from the sip lid
and when blender is no longer in use.
7 Refer to the Care & Maintenance section for cleaning and
storage instructions.
CARE & MAINTENANCE
CLEANING
Blades can still operate when the lid is removed. Always turn the unit OFF when cleaning without the lid on
or when the BlastBlade™ Assembly is exposed.
Hand-Washing
Wash vessel, lid, and BlastBlade™ Assembly with warm, soapy water. Use a dishwashing utensil or cloth
to clean the BlastBlade™ Assembly on the motor base. Exercise care when handling the BlastBlade™
Assembly on the motor base as the blades are sharp. Wipe the motor base with a clean, damp cloth.
DO NOT submerge the motor base in water. Thoroughly rinse and air-dry all appropriate parts.
Motor Base
The USB-C port and the Motor Base are is water resistant, which means the motor base can get rinsed
in the sink; HOWEVER DO NOT put the motor base in the dishwasher or submerge it in water. Ensure the
USB-C charger is not inserted before cleaning.
DEEPER CLEAN
Dishwasher
Vessel and sip lid are top-rack dishwasher safe. DO NOT use a heated dry cycle. Ensure the vessel
and sip lid are removed from the motor base before being placed in the dishwasher.
STORING
Store the unit upright and with the lid, vessel, and motor base fully assembled.
DO NOT store blended or unblended ingredients in the vessel with the BlastBlade™ Assembly
for prolonged periods of time.
DO NOT stack items on top of the vessel. Store any remaining attachments alongside the unit
or in a cabinet where they will not be damaged or create a hazard.
If your unit needs servicing, call Customer Service at 1-877-646-5288. So we may better assist you, please
register your product online at registeryourninja.com and have the product on hand when you call.
ORDERING REPLACEMENT PARTS
To order additional parts and attachments, visit ninjaaccessories.com.
ninjakitchen.com
ninjakitchen.com
TROUBLESHOOTING GUIDE
WARNING: To reduce the risk of shock and unintended operation, turn OFF unit before
troubleshooting.
Ensure the unit is not charging when troubleshooting. Ensure the unit is fully charged and vessel
is properly aligned.
Control panel doesn’t turn o.
• Press the
button to turn the unit ON and OFF.
Doesn’t mix well; ingredients get stuck.
• If ingredients are routinely getting stuck, adding some liquid will usually help. You can also shake the
blender while blending or turn the blender upside down, start a blend cycle, and turn it right side up
to move ingredients while blending.
• When filling the vessel, start with liquid or yogurt, then fresh fruit or veggies, followed by leafy greens
or herbs. Add your seeds, powders, or nut butters and end with ice or frozen ingredients.
Sip lid is hard to assemble on the vessel.
• Set the assembled motor base and vessel on a level surface. Carefully place the sip lid on the top of the
vessel and align the threads so the sip lid sits flat. Turn clockwise until you have a tight seal.
Vessel is hard to assemble on the motor base.
• Set the motor base on a level surface. Carefully place the vessel on the top of the motor base and align
the threads so the vessel sits flat. Turn clockwise until you have a tight seal. The LEDs on the UI should
flash blue when the vessel is properly aligned.
PRODUCT REGISTRATION
FCC WARNINGS
Please visit registeryourninja.com to register your new Ninja® product within ten (10) days of purchase.
You will be asked to provide the store name, date of purchase, and model number along with your name
and address.
The registration will enable us to contact you in the unlikely event of a product safety notification.
By registering, you acknowledge you have read and understood the instructions for use and warnings
set forth in the accompanying instructions.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
The One (1) Year Limited Warranty applies to purchases made from authorized retailers of
SharkNinja Operating LLC. Warranty coverage applies to the original owner and to the original
product only and is not transferable.
SharkNinja warrants that the unit shall be free from defects in material and workmanship for a period
of one (1) year from the date of purchase when it is used under normal household conditions and
maintained according to the requirements outlined in the Owner’s Guide, subject to the following
conditions and exclusions:
What is covered by this warranty?
1. The original unit and/or non-wearable parts deemed defective, in SharkNinja’s sole discretion,
will be repaired or replaced up to one (1) year from the original purchase date.
2. In the event a replacement unit is issued, the warranty coverage ends six (6) months following
the receipt date of the replacement unit or the remainder of the existing warranty, whichever is
later. SharkNinja reserves the right to replace the unit with one of equal or greater value.
What is not covered by this warranty?
1. Normal wear and tear of wearable parts (such as blending vessels, lids, cups, blades, blender
bases, removable pots, racks, pans, etc.), which require regular maintenance and/or replacement
to ensure the proper functioning of your unit, are not covered by this warranty. Replacement
parts are available for purchase at ninjaaccessories.com.
2. Any unit that has been tampered with or used for commercial purposes.
3. Damage caused by misuse, abuse, negligent handling, failure to perform required maintenance
(e.g., failure to keep the well of the motor base clear of food spills and other debris), or damage
due to mishandling in transit.
4. Consequential and incidental damages.
5. Defects caused by repair persons not authorized by SharkNinja. These defects include damages
caused in the process of shipping, altering, or repairing the SharkNinja product (or any of its parts)
when the repair is performed by a repair person not authorized by SharkNinja.
6. Products purchased, used, or operated outside North America.
How to get service
If your appliance fails to operate properly while in use under normal household conditions within the
warranty period, visit ninjakitchen.com/support for product care and maintenance self-help. Our
Customer Service Specialists are also available at 1-877-646-5288 to assist with product support
and warranty service options, including the possibility of upgrading to our VIP warranty service
options for select product categories. So we may better assist you, please register your product
online at registeryourninja.com and have the product on hand when you call.
SharkNinja will cover the cost for the customer to send in the unit to us for repair or replacement. A fee
of $20.95 (subject to change) will be charged when SharkNinja ships the repaired or replacement unit.
How to initiate a warranty claim
You must call 1-877-646-5288 to initiate a warranty claim. You will need the receipt as proof of purchase.
We also ask that you register your product online at registeryourninja.com and have the product on
hand when you call, so we may better assist you. A Customer Service Specialist will provide you with
return and packing instruction information.
How state law applies
This warranty gives you specifi c legal rights, and you also may have other rights that vary from state
to state. Some states do not permit the exclusion or limitation of incidental or consequential damages,
so the above may not apply to you.
ONE (1) YEAR LIMITED WARRANTY
NJA_1_YR_IB_LMTD_WRNTY_US_ENG
ninjakitchen.com
ninjakitchen.com
TROUBLESHOOTING GUIDE
WARNING: To reduce the risk of shock and unintended operation, turn OFF unit before
troubleshooting.
Ensure the unit is not charging when troubleshooting. Ensure the unit is fully charged and vessel
is properly aligned.
Control panel doesn’t turn o.
• Press the
button to turn the unit ON and OFF.
Doesn’t mix well; ingredients get stuck.
• If ingredients are routinely getting stuck, adding some liquid will usually help. You can also shake the
blender while blending or turn the blender upside down, start a blend cycle, and turn it right side up
to move ingredients while blending.
• When filling the vessel, start with liquid or yogurt, then fresh fruit or veggies, followed by leafy greens
or herbs. Add your seeds, powders, or nut butters and end with ice or frozen ingredients.
Sip lid is hard to assemble on the vessel.
• Set the assembled motor base and vessel on a level surface. Carefully place the sip lid on the top of the
vessel and align the threads so the sip lid sits flat. Turn clockwise until you have a tight seal.
Vessel is hard to assemble on the motor base.
• Set the motor base on a level surface. Carefully place the vessel on the top of the motor base and align
the threads so the vessel sits flat. Turn clockwise until you have a tight seal. The LEDs on the UI should
flash blue when the vessel is properly aligned.
PRODUCT REGISTRATION
FCC WARNINGS
Please visit registeryourninja.com to register your new Ninja® product within ten (10) days of purchase.
You will be asked to provide the store name, date of purchase, and model number along with your name
and address.
The registration will enable us to contact you in the unlikely event of a product safety notification.
By registering, you acknowledge you have read and understood the instructions for use and warnings
set forth in the accompanying instructions.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
The One (1) Year Limited Warranty applies to purchases made from authorized retailers of
SharkNinja Operating LLC. Warranty coverage applies to the original owner and to the original
product only and is not transferable.
SharkNinja warrants that the unit shall be free from defects in material and workmanship for a period
of one (1) year from the date of purchase when it is used under normal household conditions and
maintained according to the requirements outlined in the Owner’s Guide, subject to the following
conditions and exclusions:
What is covered by this warranty?
1. The original unit and/or non-wearable parts deemed defective, in SharkNinja’s sole discretion,
will be repaired or replaced up to one (1) year from the original purchase date.
2. In the event a replacement unit is issued, the warranty coverage ends six (6) months following
the receipt date of the replacement unit or the remainder of the existing warranty, whichever is
later. SharkNinja reserves the right to replace the unit with one of equal or greater value.
What is not covered by this warranty?
1. Normal wear and tear of wearable parts (such as blending vessels, lids, cups, blades, blender
bases, removable pots, racks, pans, etc.), which require regular maintenance and/or replacement
to ensure the proper functioning of your unit, are not covered by this warranty. Replacement
parts are available for purchase at ninjaaccessories.com.
2. Any unit that has been tampered with or used for commercial purposes.
3. Damage caused by misuse, abuse, negligent handling, failure to perform required maintenance
(e.g., failure to keep the well of the motor base clear of food spills and other debris), or damage
due to mishandling in transit.
4. Consequential and incidental damages.
5. Defects caused by repair persons not authorized by SharkNinja. These defects include damages
caused in the process of shipping, altering, or repairing the SharkNinja product (or any of its parts)
when the repair is performed by a repair person not authorized by SharkNinja.
6. Products purchased, used, or operated outside North America.
How to get service
If your appliance fails to operate properly while in use under normal household conditions within the
warranty period, visit ninjakitchen.com/support for product care and maintenance self-help. Our
Customer Service Specialists are also available at 1-877-646-5288 to assist with product support
and warranty service options, including the possibility of upgrading to our VIP warranty service
options for select product categories. So we may better assist you, please register your product
online at registeryourninja.com and have the product on hand when you call.
SharkNinja will cover the cost for the customer to send in the unit to us for repair or replacement. A fee
of $20.95 (subject to change) will be charged when SharkNinja ships the repaired or replacement unit.
How to initiate a warranty claim
You must call 1-877-646-5288 to initiate a warranty claim. You will need the receipt as proof of purchase.
We also ask that you register your product online at registeryourninja.com and have the product on
hand when you call, so we may better assist you. A Customer Service Specialist will provide you with
return and packing instruction information.
How state law applies
This warranty gives you specifi c legal rights, and you also may have other rights that vary from state
to state. Some states do not permit the exclusion or limitation of incidental or consequential damages,
so the above may not apply to you.
ONE (1) YEAR LIMITED WARRANTY
NJA_1_YR_IB_LMTD_WRNTY_US_ENG
REGISTER YOUR PURCHASE
registeryourninja.com
Scan QR code using mobile device
@ninjakitchen
SharkNinja Operating LLC
US: Needham, MA 02494
1-877-646-5288
ninjakitchen.com
Illustrations may dier from actual product. We are constantly striving to improve our products;
therefore the specifications contained herein are subject to change withoutnotice.
BLASTBLADE and NINJA BLAST are trademarks of SharkNinja Operating LLC.
This product may be covered by one or more U.S. patents.
See sharkninja.com/patents for more information.
© 2023 SharkNinja Operating LLC
BC100Series_IB_MP_Mv10
TECHNICAL SPECIFICATIONS
Voltage: 5v
RECORD THIS INFORMATION
Model Number: ____________________
Serial Number: _____________________
Date of Purchase: ___________________
(Keep receipt)
Store of Purchase: __________________
