Installation Instructions
Surfaces must be clean, dry and relatively smooth.
To ensure a better bond, heat gently with a WARM (not hot!) heat gun
before xing. This ensures the adhesive is more tacky and produces
a better bond. The substrate temperature must also be above 10°C /
50°F.
Slowly remove the release paper, then carefully locate the anti-
slip tape. Once placed correctly, use a wallpaper seam roller or
rubber mallet to bond the tape into place securely. Press rmly with
ngers over imperfections to seal completely. Whilst this product is
waterproof, it is only as good as the seal that is created. Ensure there
are no gaps where water could soak beneath the tape to loosen the
bond.
Substrate Instructions
Wood - New wood should be sealed or painted. Remove any aking
paint with glasspaper or a wire brush. Anti-slip tape will not adhere to
wood treated with creosote or other wood preservatives.
Metal - Anti-slip tape adheres better to painted or primed surfaces.
Remove any rust or aking paint with glasspaper or a wire brush.
Concrete - must be smooth for anti-slip tape to bond rmly. Vacuum
surface to remove any dust.
All other surfaces must be relatively smooth, dry and dust free.
Anti-slip tape can be used immediately.
Please Note:
No warranties expressed or implied are made or to be inferred.
Sellers and manufacturers only obligation shall be to replace such
quantity of the product proved to be defective. Neither seller nor
manufacturers shall be liable for any injury, loss or damage, direct
or consequential, arising out of the use of the inability to use the
product. Before installing, purchaser shall determine the suitability
of the product for its intended use and assumes all risk and liability
whatsoever in connection therewith. (Issue 1 - 06/01/16)
Installation Instructions
Surfaces must be clean, dry and relatively smooth.
To ensure a better bond, heat gently with a WARM (not hot!) heat gun
before xing. This ensures the adhesive is more tacky and produces
a better bond. The substrate temperature must also be above 10°C /
50°F.
Slowly remove the release paper, then carefully locate the anti-
slip tape. Once placed correctly, use a wallpaper seam roller or
rubber mallet to bond the tape into place securely. Press rmly with
ngers over imperfections to seal completely. Whilst this product is
waterproof, it is only as good as the seal that is created. Ensure there
are no gaps where water could soak beneath the tape to loosen the
bond.
Substrate Instructions
Wood - New wood should be sealed or painted. Remove any aking
paint with glasspaper or a wire brush. Anti-slip tape will not adhere to
wood treated with creosote or other wood preservatives.
Metal - Anti-slip tape adheres better to painted or primed surfaces.
Remove any rust or aking paint with glasspaper or a wire brush.
Concrete - must be smooth for anti-slip tape to bond rmly. Vacuum
surface to remove any dust.
All other surfaces must be relatively smooth, dry and dust free.
Anti-slip tape can be used immediately.
Please Note:
No warranties expressed or implied are made or to be inferred.
Sellers and manufacturers only obligation shall be to replace such
quantity of the product provd to be defective. Neither seller nor
manufacturers shall be liable for any injury, loss or damage, direct
or consequential, arising out of the use of the inability to use the
product. Before installing, purchaser shall determine the suitability
of the product for its intended use and assumes all risk and liability
whatsoever in connection therewith. (Issue 1 - 06/01/16)
Installation Instructions
Surfaces must be clean, dry and relatively smooth.
To ensure a better bond, heat gently with a WARM (not hot!) heat gun
before xing. This ensures the adhesive is more tacky and produces
a better bond. The substrate temperature must also be above 10°C /
50°F.
Slowly remove the release paper, then carefully locate the anti-
slip tape. Once placed correctly, use a wallpaper seam roller or
rubber mallet to bond the tape into place securely. Press rmly with
ngers over imperfections to seal completely. Whilst this product is
waterproof, it is only as good as the seal that is created. Ensure there
are no gaps where water could soak beneath the tape to loosen the
bond.
Substrate Instructions
Wood - New wood should be sealed or painted. Remove any aking
paint with glasspaper or a wire brush. Anti-slip tape will not adhere to
wood treated with creosote or other wood preservatives.
Metal - Anti-slip tape adheres better to painted or primed surfaces.
Remove any rust or aking paint with glasspaper or a wire brush.
Concrete - must be smooth for anti-slip tape to bond rmly. Vacuum
surface to remove any dust.
All other surfaces must be relatively smooth, dry and dust free.
Anti-slip tape can be used immediately.
Please Note:
No warranties expressed or implied are made or to be inferred.
Sellers and manufacturers only obligation shall be to replace such
quantity of the product provd to be defective. Neither seller nor
manufacturers shall be liable for any injury, loss or damage, direct
or consequential, arising out of the use of the inability to use the
product. Before installing, purchaser shall determine the suitability
of the product for its intended use and assumes all risk and liability
whatsoever in connection therewith. (Issue 1 - 06/01/16)
Installation Instructions
Surfaces must be clean, dry and relatively smooth.
To ensure a better bond, heat gently with a WARM (not hot!) heat gun
before xing. This ensures the adhesive is more tacky and produces
a better bond. The substrate temperature must also be above 10°C /
50°F.
Slowly remove the release paper, then carefully locate the anti-
slip tape. Once placed correctly, use a wallpaper seam roller or
rubber mallet to bond the tape into place securely. Press rmly with
ngers over imperfections to seal completely. Whilst this product is
waterproof, it is only as good as the seal that is created. Ensure there
are no gaps where water could soak beneath the tape to loosen the
bond.
Substrate Instructions
Wood - New wood should be sealed or painted. Remove any aking
paint with glasspaper or a wire brush. Anti-slip tape will not adhere to
wood treated with creosote or other wood preservatives.
Metal - Anti-slip tape adheres better to painted or primed surfaces.
Remove any rust or aking paint with glasspaper or a wire brush.
Concrete - must be smooth for anti-slip tape to bond rmly. Vacuum
surface to remove any dust.
All other surfaces must be relatively smooth, dry and dust free.
Anti-slip tape can be used immediately.
Please Note:
No warranties expressed or implied are made or to be inferred.
Sellers and manufacturers only obligation shall be to replace such
quantity of the product provd to be defective. Neither seller nor
manufacturers shall be liable for any injury, loss or damage, direct
or consequential, arising out of the use of the inability to use the
product. Before installing, purchaser shall determine the suitability
of the product for its intended use and assumes all risk and liability
whatsoever in connection therewith. (Issue 1 - 06/01/16)
INSTRUCTIONS FOR
ANTI-SLIP TAPE SELF-ADHESIVE
BLACK/YELLOW 50MM X 18MTR
MODEL NO: ANTBY18
INSTRUCTIONS FOR
ANTI-SLIP TAPE SELF-ADHESIVE
BLACK/YELLOW 50MM X 18MTR
MODEL NO: ANTBY18
INSTRUCTIONS FOR
ANTI-SLIP TAPE SELF-ADHESIVE
BLACK/YELLOW 50MM X 18MTR
MODEL NO: ANTBY18
INSTRUCTIONS FOR
ANTI-SLIP TAPE SELF-ADHESIVE
BLACK/YELLOW 50MM X 18MTR
MODEL NO: ANTBY18
