Loading ...
Loading ...
Loading ...
4
FUNCTIONAL DESCRIPTION
11
10
1
2
3
4
6
7
1. Trigger
2. Handle
3. Trigger lock
4. Power button
5. Hook
6. Magazine
7. Pusher release tab
8. Workpiece contact
9. Staple pusher
10. Jam clearing latch
11. Removeable tool hanger ring
12. Depth adjustment
8
9
12
5
ASSEMBLY
WARNING
Recharge only with the charger
specied for the battery. For spe-
cic charging instructions, read the operator’s
manual supplied with your charger and battery.
Removing/Inserting the Battery
To remove the battery, push in the release buttons
and pull the battery pack away from the tool.
WARNING
Always lock the trigger or remove
the battery pack any time the tool
is not in use.
To insert the battery, slide the pack into the body
of the tool. Make sure it latches securely into place.
WARNING
Only use accessories specically
recommended for this tool. Others
may be hazardous.
Installing Staples
WARNING
Always remove battery pack before
changing or removing staples.
Always wear safety goggles or glasses with side
shields.
To install staples:
1. Pull staple pusher to the bot-
tom of the magazine assuring it
locks in place. Load a collation
of staples from the rear of the
magazine with the legs point-
ing towards the front of the tool.
2. The staples will need to be loaded near the bottom
of the magazine and then slide into place over the
metallic portion.
a. Up to 2 full collations can be loaded in the
magazine at a time.
3. Once the staples are in the magazine, press the
tab on the bottom of the staple pusher to release
it from the locked position.
a. Do not leave staple pusher in locked position
when staples are not being loaded.
Attaching and Removing the Tool Hanger
1. To attach, place the hanger ring through the tool
hanger.
2. Position the tool hanger on the tool over the two
screw holes.
3. Insert the two screws. Hand tighten the screws.
4. To remove, reverse the procedure.
OPERATION
WARNING
To reduce the risk of injury, always
wear proper eye protection marked
to comply with ANSI Z87.1.
When working in dusty situations, wear appro-
priate respiratory protection or use an OSHA
compliant dust extraction solution.
Eye protection does not t all operators in the
same way. Make sure the eye protection chosen
has side shields or provides protection from
ying debris both from the front and sides. The
employer is responsible for enforcing the use of
eye protection by the operator and other people
in the work area. When required, wear head pro-
tection in accordance with ANSI Z89.1.
To reduce the risk of injury to yourself and others,
test the tool before beginning work each day ac-
cording to the "Required Daily Testing" section.
Do not use the tool unless you thoroughly under-
stand the actuation mode selected.
Remove battery pack and staples before leav-
ing the work area, moving the tool to another
location, or handing the tool to another person.
Failure to do so could result in serious injury.
Do not use this tool for fastening electrical
cables. It is not designed for electric cable
installation and may damage the insulation of
electric cables thereby causing electric shock
or re hazards.
NEVER wedge or hold back the workpiece con-
tact mechanism during operation of the tool.
Never attempt to clear a jammed workpiece con-
tact by grasping the discharge area of the tool.
Doing so could result in serious injury.
To avoid serious injury, do not attempt to prevent
the recoil by holding the tool too rmly against
the work. Keep face and body away from the
tool. During normal use, the tool will recoil im-
mediately after driving a staple. This is a normal
function of the tool. Restriction to the recoil can
result in a second staple being driven when the
tool is in Contact Actuation mode. Grip the handle
rmly, let the tool do the work, and do not place
a second hand on top of the tool.
Always lock the trigger or remove the battery
pack any time the tool is not in use.
Loading ...
Loading ...
Loading ...