Loading ...
Loading ...
Loading ...
7.3 Setting the Temperature Units:
To switch the temperature measurement between Celsius and Fahrenheit, press the
“UP” button which is also the C/F option button. You can switch between Celsius and
Fahrenheit at any time (except when setting other setting options.)
7.4 Checking the MAX/MIN temperature and humidity
• Press the “DOWN” button to check MAX/MIN temperature and humidity.
• Hold the “DOWN” button to clear the record of MAX/MIN temperature and humidity.
7.5 Temperature Alert
• In standard mode, press “ALERT” to enter alert mode, use “UP” or “DOWN” to turn
on or off temperature alert function.
• In standard mode, hold “ALERT” to set temperature alert function.
• Setting order:
• outdoor temperature upper limit
• outdoor temperature lower limit
• indoor temperature upper limit
• indoor temperature lower limit
• To select individual values, press UP button or the DOWN button and confirm each
selection by pressing the ALERT button.
• If you do not make an entry for 10 seconds, setting mode is exited automatically.
Note:
• In temperature alert status, alert temperature icon will flash and temperature will
always display.
• Temperature alarm sounds for every minute, and it will not stop until:
• Press any button to stop alarm but temperature and alert icon will continuously flash.
• When temperature out of the alert range.
7.6 Ice alert
When the outdoor temperature in the range of -1°C ~ +2.9°C (+30.2°F ~ +37.3°F),
the ice icon will flash, when the temperature out of the range, the icon will disappear.
Note:
The ice alert not needs setting, as long as the temperature in the alert range, the icon
will be displayed.
7.7 Temperature and humidity trend
• The device checks the temperature for trends every 30 minutes, comparing the
current temperature with the temperature from 3 hours ago.
• If the temperature rises 1 °C / 2 °F, the device will display an upward arrow.
• If the temperature drops 1 °C / 2 °F, the device will display a downward arrow.
• If the temperature stays within 1 °C / 2 °F, the device will display a horizontal arrow.
8. Backlight:
• Sustained backlight is only possible by power supply unit.
• Press the SNZ/LIGHT button to switch the brightness from HI→LOW→OFF.
• When powered by battery only, the backlight will be off (to conserve power). Press the
SNZ/LIGHT button to active the backlight for 10 seconds.
9. Weather forecast:
The unit predicts weather condition of the next 12-24 hours based on the change of
atmospheric pressure. The weather forecast is based on atmospheric pressure change
and is about 70-75% correct.
The following are icons that will show:
Note:
After setting up, weather forecast readings should be disregarded for the next 24
hours. This will allow sufficient time for the weather station to collect data and
therefore result in a more accurate forecast. Common to weather forecasting,
absolute accuracy cannot be guaranteed.
Trend of barometric
The trend of barometric: Barometer rise or down at 1 HPA within 1 hours, the arrow
will rise or down, if barometer rise or down less than 1 HPA, the arrow displays horizontal.
10、Remote sensor transmission:
This weather station is arranged to communicate with three external sensors. One
of these comes with the unit, the remaining two are optional.
• Power the weather station as described in Getting started.
• Insert the batteries in the external sensor, set the selector to the desired
transmission channel (1, 2 or 3). Automatic weather station data will be transmitted.
• Press the CH button more times to select the channel set on the external sensor.
Sequentially selects the channel 1, channel 2, channel 3 or sequential display of 3
channels (icon flashing channel).
Notes:
• Place the weather station away from equipment that generates magnetic fields
such as mobile phones, televisions etc.
• In case of non receipt of the display, signal it is shown the character -. Press and
hold the DOWN button to receive RF signal.
• Always make sure the channel chosen on the display unit matches the channel
option chosen on the outdoor sensor.
11、Week display
TV
(200 feet maximum)
(60 meters)
(0.9 m)
3 feet
AT
LEAST
APART
12、Care and maintenance
Placement of the Device:
Proper placement of both the display unit and the outdoor sensor are critical to the
accuracy and performance of this product.
Display unit placement
Place the display unit in a dry area free of dirt and dust. Display unit right for tabletop/
countertop use.
Important Placement Guideline
• To ensure accurate temperature measurement, place units out of direct sunlight
and away from any heat sources or vents.
• Display unit and outdoor sensor must be within 200 ft. (60m) of each other.
• To maximize wireless range, place units away from large metallic items, thick walls,
metal surfaces, or other objects that may limit wireless communication.
• To prevent wireless interference, place both units at least 3ft(1 m) away from
electronic devices (TV, computer, microwave,radio, etc)
Sunny Partly sunny Cloudy Rainy
TROUBLE SHOOTING
Problem
Outdoor reading
is flashing or
showing dashes
No outdoor
sensor reception
Inaccurate
temperature/
humidity
Inaccurate
Weather
Forecast
Backlight
doesn't stay on
Care and
maintenance
If your Geevon product does not operate properly after trying the troubleshooting steps,
please contact the seller on your order page or shoot an email to : [email protected].
"HH.H/LL.L" display
in indoor and/or
outdoor temperature
Flashing of the outdoor reading is generally an indication of wireless interference:
1. Relocate both of main unit and outdoor sensor. Power the weather station as
described in Getting started. (Please refer to the SENSOR SETUP section.)
2. Display unit and outdoor sensor must be within 200ft (60m) of each other.
3. Press and hold the "DOWN" button to receive RF signal.
4. Place units out of direct sunlight and AWAY FROM any heat/moisture sources
or vents.
5. Place units away from large metallic items, thick walls, metal surfaces, or other
objects that may limit wireless communication.
6. Place both units at least 3ft(1 m) away from electronic devices (TV, computer,
microwave,radio, etc.)
1. Relocate both of main unit and outdoor sensor. Power the weather
station and outdoor sensor again as described in Getting started. (Please
refer to the SENSOR SETUP section.)
2. Display unit and outdoor sensor must be within 200ft (60m) of each other.
3. Press and hold the DOWN button to receive RF signal.
4. Press the "CH" button more times to select the channel set on the
external sensor.Sequentially selects the channel 1, channel 2, channel 3 or
sequential display of 3 channels (icon flashing channel).
5. Always make sure the channel chosen on the display unit MATCHES the
channel option chosen on the outdoor sensor.
6. Do not use heavy duty or rechargeable batteries. The outdoor sensor
requires lithium batteries in low temperature conditions. Cold temperatures
would cause alkaline batteries work improperly.
7. Do not mix old and new batteries.
8. Place the weather station away from equipment that generates magnetic
fields such as mobile phones, televisions etc.
1. When it is first stalled,it takes at least 1 Hour to have accurate
temperature and humidity data.
2. Make sure both the main unit and sensor are placed out of direct sunlight
and AWAY FROM any heat sources, vents or moisture sources.
3. Do not tamper with the internal components.
Temperature Accuracy: -22°F – -4°F(-30°C ~ -20°C): ±39.2°F(± 4°C)
-4°F – 32°F(-20°C ~ 0°C): ±35.6°F(± 2°C)
32°F – 122°F(0°C ~ +50°C): ±33.8°F(±1°C)
Humidity Accuracy:
±5% from 35% to 75% and ±10% from 20% to 35%& 75% to 95%.
1. Weather forecast readings should be disregarded for the next 24 hours.
This will allow sufficient time for the weather station to collect data
andtherefore result in a more accurate forecast.
2. Common to weather forecasting, absolute accuracy cannot be guaranteed.
The backlight turns off after 10s to save energy when powered by batteries. If
you want the weather station always lights on, please plug in with power adaptor.
If the temperature is higher than the detection range, HH.H will display on
screen for indication;If lower than the detection range, LL.L will display on
screen for indication.
1. Place the display unit in a dry area free of dirt and dust.
2. The remote sensor is totally wireless but has to avoid direct sunlight and rain.
3. Please immediately change the batteries if the low battery indicator is
displayed on the LCD screen of main unit.
4. Never immerse the product in water. This will damage the product.
5. Do not subject the product to extreme force, shock, or fluctuations in temperature.
6. Do not clean any part of the product with benzene,thinner or other solvent
chemicals. When necessary, clean it with a soft cloth.
Possible Solution
Loading ...