IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should always be
followed. These instructions should be saved for future reference:
• Read and familiarise yourself with all operating instructions before using
this Hot Plate.
• Before plugging your unit into the mains, visually check that the unit is
intact and has not suffered any transit damage.
• Check that the voltage indicated on the data plate corresponds with that
of the local network before connecting the appliance to the mains power
supply.
• Close supervision is required when using this appliance near children.
• This appliance can be used by children aged from 8 years and above
and persons with reduced physical, sensory or mental capabilities or
lack of experience and knowledge if they have been given supervision
or instruction concerning use of the appliance in a safe way and
understand the hazards involved. Children shall not play with the
appliance. Cleaning and user maintenance shall not be made by
children unless they are older than 8 and supervised.
• Keep the appliance and its cord out of reach of children less than 8
years.
• DO NOT touch hot surfaces. The outer surfaces are liable to get hot
during use. Always use the handles and knobs.
• Do not immerse the appliance or its cord in water or any other liquids.
• Do not leave the appliance unattended during use.
• Do not leave the appliance unattended whilst connected to the mains
supply.
• Always use this appliance on a solid, level, non-flammable surface.
• Do not use this appliance outdoors.
• Do not use this Hot Plate with a programmer, timer, separate remote-
control system or any other device that switches the appliance on
automatically.
• It is imperative to unplug the power cord after the appliance has been
used, before it is cleaned and whilst being repaired.
• Repairs to electrical appliances should only be performed by a qualified
electrician. Improper repairs may place user at serious risk.
• Do not operate this appliance with a damaged plug or cord, after a
malfunction or after being dropped or damaged in any way.
• Regular, periodic checks should be carried out on the mains cable to
ensure no damage is evident. Should there be any signs of damage the
appliance should not be used.
• If the power cable is damaged, it should only be replaced by the
manufacturer or a suitable qualified after-sales-service in order to avoid
a hazard
• Do not allow the mains cable to hang over sharp edges or come in
contact with hot surfaces.
• Do not run the mains cable under carpets, rugs, etc.
• Allow the unit to cool before storage.
• Before cleaning, disconnect the appliance from the mains supply and
allow to cool.
• This appliance is intended for household use only and should not be
used for industrial purposes.
• Do not use any accessories or attachments with this appliance other
than those supplied or recommended by supplier.
• Do not use this appliance for anything other than its intended use.
• Do not push objects into any openings as damage to the appliance
and/or electric shock may occur.
• Ensure appliance is situated in an open area, do not allow it to come in
contact with Cupboards, Curtains, wall coverings, clothing or other
flammable materials.
• Unplug after each use. Grasp the plug, not the cord.
NB During the first few minutes of initial use, you may notice a slight
odour and a little smoke. This is normal and will quickly disappear, it is the
coating applied to the heating elements to prevent any corrosion during
transit.
Description of parts
Hot Plate
Thermostat Control
Neon Indicator
Before the first time you use your Hot Plate
Please read these operating instructions thoroughly and keep them in a safe place
for future reference.
Remove all packing materials and discard responsibly.
Before using your Hot Plate for the first time, turn the Thermostat control to the
highest setting (5) for 3 to 5 minutes to condition the protective coating.
NB This should be the only time the Hot Plate is operated without a cooking
utensil on it.
A pan 15 - 17cm in diameter is recommended for best results. Smaller pans are
not recommended. Ensure larger pans do not protrude beyond the edge of the
Hot Plate or the controls.
Operating Instructions
• Place the Hot Plate on a solid, level non-flammable surface.
• Ensure that Thermostat Control is in the off position.
• Insert the mains plug into the mains socket.
• Rotate the Thermostat Control clockwise from 0 (low heat) through to 5 (high
heat) and leave at the desired setting. The Neon Indicator will light to show the
hot plate is heating up.
• Once the hot plate is at the correct temperature and ready to use, the Neon
Indicator will go out.
NB the Neon Indicator will go on and off during use to show the temperature of
the hot plate is being maintained.
• Return the Thermostat control to the position and remove the mains plug
from the socket after use.
Care and Use of your Hot Plate
• Always disconnect the Hot Plate from the mains power supply and allow
to cool before cleaning.
• Clean the outside of the Hot Plate with a soft damp cloth. Never clean
the Hot Plate with harsh or abrasive cleaners.
• Do not submerge any part of Hot Plate or its cord in water or any other
liquids.
Technical Data
Voltage : 220-240V AC 50/60Hz
Rated power : 1500 W
Model Number : SDA1731
Electrical Connections
This appliance is fitted with a fused three-pin plug to BS 1363. If the plug has to
be removed, it should be cut off and carefully disposed of immediately. To avoid
a possible shock hazard, do not insert the discarded plug into a mains socket.
Fitting a new plug
The mains lead must be connected as shown below. The wires are coloured
with the following code - Brown wire = Live (L), Blue wire = Neutral (N),
Green & Yellow = Earth (E).
• The Blue wire must be connected to the terminal marked N or coloured Black.
• The Brown wire must be connected to the terminal marked L or coloured Red.
• The Green & Yellow wire must be connected to the terminal marked E or
coloured Green.
• Check that there are no cut or stray strands of wire inside the plug.
• Use a 13 Amp BS 1362 fuse, only use BSI or ASTA approved fuses.
• If you are in any way unsure which plug or fuse to use, always refer to a
qualified electrician.
• After replacing or changing a fuse on a moulded plug, the cover must be
refitted to the plug; the appliance must not be used without a fuse cover.
Connect
Green &
Yellow to
Earth (E)
Ensure the outer sheath is
securely held by the cord clamp
Connect
Brown to
Live (L)
Connect
Blue to
Neutral (N)
