Loading ...
Loading ...
Loading ...
10
compliance with the electrical safety regulations of the
nation and region. The equipment shall not be exposed
to dripping or splashing and that no objects filled with
liquids, such as vases, shall be placed on the equipment.
Provide a surge suppressor at the inlet opening of the
equipment under special conditions such as the
mountain top, iron tower, and forest. CAUTION: To
reduce the risk of fire, replace only with the same type
and rating of fuse.
Battery
Do not ingest battery. Chemical burn hazard! This
product contains a coin/button cell battery. If the
coin/button cell battery is swallowed, it can cause severe
internal burns in just 2 hours and can lead to death. Keep
new and used batteries away from children. If the
battery compartment does not close securely, stop
using the product and keep it away from children. If you
think batteries might have been swallowed or placed
inside any part of the body, seek immediate medical
attention. CAUTION: Risk of explosion if the battery is
replaced by an incorrect type. Dispose of used batteries
according to the instructions. Improper replacement of
the battery with an incorrect type may defeat a
safeguard (for example, in the case of some lithium
battery types). Do not dispose of the battery into fire or
a hot oven, or mechanically crush or cut the battery,
which may result in an explosion. Do not leave the
battery in an extremely high temperature surrounding
environment, which may result in an explosion or the
leakage of flammable liquid or gas. Do not subject the
battery to extremely low air pressure, which may result
in an explosion or the leakage of flammable liquid or
gas. + identifies the positive terminal(s) of equipment
which is used with, or generates direct current. -
identifies the negative terminal(s) of equipment which
is used with, or generates direct current.
Fire Prevention
No naked flame sources, such as lighted candles, should
be placed on the equipment. The serial port of the
equipment is used for debugging only.
Hot Surface Prevention
CAUTION: Hot parts! Burned
fingers when handling the parts.
Wait one-half hour after switching
off before handling parts. This
sticker is to indicate that the marked item can be hot
and should not be touched without taking care. For
device with this sticker, this device is intended for
installation in a restricted access location, access can
only be gained by service persons or by users who have
been instructed about the reasons for the restrictions
applied to the location and about any precautions that
shall be taken.
Installation
Install the equipment according to the instructions in
this manual.
Power Supply
Device powered by Safety Extra-Low Voltage(SELV): The
power source should meet limited power source or PS2
requirements according to IEC 60950-1 or IEC 62368-1
standard.
Device powered by AC mains supply voltage: The
equipment must be connected to an earthed mains
socket-outlet. An appropriate readily accessible
disconnect device shall be incorporated external to the
equipment. An appropriate overcurrent protective
device shall be incorporated external to the equipment,
not exceeding the specification of the building. An
all-pole mains switch shall be incorporated in the
electrical installation of the building. Ensure correct
wiring of the terminals for connection to an AC mains
supply. The equipment has been designed, when
required, modified for connection to an IT power
distribution system.
White Light Illuminator (If supported)
Possibly hazardous optical radiation emitted from this
product. DO NOT stare at operating light source. May
be harmful to the eyes. Wear appropriate eye
protection or DO NOT turn on the white light when you
assemble, install or maintain the camera.
Transportation
Keep the device in original or similar packaging while
transporting it.
System Security
The installer and user are responsible for password and
security configuration.
Maintenance
If the product does not work properly, please contact
your dealer or the nearest service center. We shall not
assume any responsibility for problems caused by
unauthorized repair or maintenance. A few device
components (e.g., electrolytic capacitor) require regular
replacement. The average lifespan varies, so periodic
checking is recommended. Contact your dealer for
details.
Cleaning
Please use a soft and dry cloth when clean inside and
outside surfaces of the product cover. Do not use
alkaline detergents.
Using Environment
DO NOT place the camera in extremely hot, cold, dusty
or damp locations, and do not expose it to high
electromagnetic radiation.
Emergency
If smoke, odor, or noise arises from the device,
immediately turn off the power, unplug the power
cable, and contact the service center.
Time Synchronization
Set up device time manually for the first time access if
the local time is not synchronized with that of the
network. Visit the device via Web browse/client
software and go to time settings interface.
Reflection
Make sure that no reflective surface is too close to the
device lens. The IR light from the device may reflect
back into the lens causing reflection.
Français
Ces clauses ne s’appliquent qu’aux produits portant la
marque ou l’information correspondante.
Déclaration de conformité UE
Ce produit et - le cas échéant - les
accessoires fournis sont marqués
« CE » et sont donc conformes aux
normes européennes harmonisées
applicables énumérées dans la
directive CEM 2014/30/UE, la directive DBT 2014/35/UE,
la directive RoHS 2011/65/UE, dispositif Wi-Fi : la
directive RE 2014/53/UE
Loading ...
Loading ...
Loading ...