Loading ...
Loading ...
Loading ...
5
FUNCTIONAL DESCRIPTION
2
7
8
1
6
5
3
1. Crimping jaws
2. Lift ring
3. LEDs/Crimping
indicator
4. Internal battery
5. ONE KEY
TM
indicator
6. Handle
7. Reverse trigger
8. Trigger
9. Die release pins
4
9
ASSEMBLY
WARNING
Recharge only with the charger
specied for the battery. For spe-
cic charging instructions, read the operator’s
manual supplied with your charger and battery.
Removing/Inserting the Battery
To remove the battery, push in the release buttons
and pull the battery pack away from the tool.
WARNING
Always remove battery pack before
changing or removing accessories.
To insert the battery, slide the pack into the body
of the tool. Make sure it latches securely into place.
WARNING
Only use accessories specically
recommended for this tool. Others
may be hazardous.
WARNING
An incomplete or faulty crimp could
cause a re. Use tool only with
MILWAUKEE "U" dies and connectors for which
they are rated. Jaws, dies, and connectors must
be used in an approved combination to achieve
a successful operation. Improper combinations
can result in a faulty crimp. Electric shock, re,
explosion, and property damage could occur.
Changing the Dies
Inspect dies and connectors before use. Only use
properly matched dies and connectors for the crimp-
ing jaws. Refer to Specications for die/connector
compatibility.
1. Remove the battery pack.
2. Snap the appropriate dies into each side of the
crimping jaws.
3. To remove, press the release button for each side
of the crimping jaws. Pull dies out from crimping
jaws.
ONE-KEY™
To learn more about the ONE-KEY™ functionality
for this tool, go to milwaukeetool.com/One-Key. To
download the ONE-KEY™ app, visit the App Store
or Google Play from your smart device.
ONE-KEY™ Indicator
Solid Blue Wireless mode is active and ready
to be congured via the ONE-KEY™
app.
Blinking Blue Tool is actively communicating with
the ONE-KEY™ app.
Blinking Red Tool is in security lockout and can
be unlocked by the owner via the
ONE-KEY™ app.
OPERATION
WARNING
To reduce the risk of arc ash,
electric shock and property
damage, work on deenergized lines when
possible. Tool is not insulated. Should work
on energized lines be required, ensure all proper
precautions, including those contained in NFPA
70E, have been taken rst.
Keep hands away from crimping jaws while
tool is in use. Fingers could be crushed.
Always remove battery pack before changing
or removing accessories. Only use accessories
specically recommended for this tool. Others
may be hazardous.
Always wear proper eye protection marked to
comply with ANSI Z87.1.
Crimping
Before crimping:
•
Inspect the jaws and dies for cracks or other dam-
age. Do not use damaged jaws or dies. Contact a
MILWAUKEE
service facility.
•
Ensure dies are properly installed.
•
Jaws, dies, connectors, and cables must
be used in
an APPROVED COMBINATION
. Improper combina-
tions can result in a faulty crimp.
•
Inspect and discard workpieces with cracks or wear
before use. Materials may crack or shatter.
•Foll
ow installation specications as specied in
Table A using an Approved Combination of jaws,
dies, connectors and cables as indicated. Other
uses may cause damage to the tool, accessories,
and workpiece.
1. Install the dies.
2. Insert battery pack.
3. Rotate the jaws to the desired angle. Hold tool
securely. Press and hold the trigger.
4. When the cycle is complete the tool will switch
o and the indicator will light. Release the trigger.
Press and hold the reverse trigger to manually
return the crimping jaws.
NOTE: After the cycle reaches a certain point, the
crimp may automatically nish, even if the trigger
is released.
Loading ...
Loading ...
Loading ...