Loading ...
Loading ...
Loading ...
5
WARNING
To reduce the risk of injury, do not
cut short pieces of pipe that put
ngers near blade and lower jaw. Keep
hands away from all cutting edges and
moving parts. Laceration and amputa-
tion can occur. Blade is sharp.
Always wear proper eye protection marked to
comply with ANSI Z87.1. Plastic pipe may crack
or shatter.
Only cut recommended materials (see "Speci-
cations"). Do not attempt to cut wires, branches,
metal pipes, or other materials.
Cutting
1. Open the blade.
2. Insert the workpiece squarely between the lower
jaw and the blade. Do not attempt to make angled
cuts as it will damage the workpiece and blade.
3. Line up the cutting line and the blade.
4. Hold the tool rmly and support the workpiece.
Ensure the workpiece is straight and centered in
the jaws. Keep hand away from jaws and blade.
5. Press the trigger unlock button and pull the trig-
ger. Workpiece may move slightly during the cut.
6. When the cut is complete, the tool will stop. Re-
lease the trigger.
Cutting Tips
• Pipe can crack or shatter at any time. Always use
caution and begin the cut slowly.
• Pipe becomes more brittle in lower temperatures,
increasing the risk of cracking or shattering. Cutting
pipe with this tool is not recommended below 40°F.
• Short or thin-wall pieces of pipe may shatter or col-
lapse when cut. If you cannot hold the workpiece
safely, it is too short to be cut.
• Cut slowly and further in from the end of the pipe
to avoid crooked cuts,.
• A single "click" when starting a cut is normal - the
blade is engaging the closing mechanism.
• Do not attempt angled cuts. It will damage the blade.
Hold the pipe squarely in the jaws.
• Cut clean material to extend the blade life. Wipe
dirt and debris from pipe before beginning the cut.
MAINTENANCE
WARNING
To reduce the risk of injury, always
unplug the charger and remove the
battery pack from the charger or tool before
performing any maintenance. Never disassemble
the tool, battery pack or charger. Contact a
MILWAUKEE service facility for ALL repairs.
Maintaining Tool
Keep your tool, battery pack and charger in good
repair by adopting a regular maintenance program.
Inspect your tool for issues such as undue noise,
misalignment or binding of moving parts, breakage of
parts, or any other condition that may aect the tool
operation. Return the tool, battery pack, and charger
to a MILWAUKEE service facility for repair. After six
months to one year, depending on use, return the
tool, battery pack and charger to a MILWAUKEE
service facility for inspection.
If the tool does not start or operate at full power with
a fully charged battery pack, clean the contacts on
the battery pack. If the tool still does not work prop-
erly, return the tool, charger and battery pack, to a
MILWAUKEE service facility for repairs.
WARNING
To reduce the risk of personal in-
jury and damage, never immerse
your tool, battery pack or charger in liquid or
allow a liquid to ow inside them.
Cleaning
Clean dust and debris from vents. Keep handles
clean, dry and free of oil or grease. Use only mild
soap and a damp cloth to clean, since certain clean-
ing agents and solvents are harmful to plastics and
other insulated parts. Some of these include gasoline,
turpentine, lacquer thinner, paint thinner, chlorinated
cleaning solvents, ammonia and household deter-
gents containing ammonia. Never use ammable or
combustible solvents around tools.
Repairs
For repairs, return the tool, battery pack and charger
to the nearest authorized service center.
ACCESSORIES
WARNING
Use only recommended accesso-
ries. Others may be hazardous.
For a complete listing of accessories, go online to
www.milwaukeetool.com or contact a distributor.
SERVICE - UNITED STATES
1-800-SAWDUST (1.800.729.3878)
Monday-Friday, 7:00 AM - 6:30 PM CST
or visit www.milwaukeetool.com
Contact Corporate After Sales Service Technical
Support with technical, service/repair, or warranty
questions.
Email: [email protected]
Become a Heavy Duty Club Member at
www.milwaukeetool.com to receive important
notications regarding your tool purchases.
SERVICE - CANADA
Milwaukee Tool (Canada) Ltd
1.800.268.4015
Monday-Friday, 7:00 AM - 4:30 PM CST
or visit www.milwaukeetool.ca
LIMITED WARRANTY
USA & CANADA
Every MILWAUKEE power tool* (see exceptions below) is warranted
to the original purchaser only to be free from defects in material and
workmanship. Subject to certain exceptions, MILWAUKEE will repair
or replace any part on an electric power tool which, after examination,
is determined by MILWAUKEE to be defective in material or workman-
ship for a period of ve (5) years** after the date of purchase unless
otherwise noted. Return of the power tool to a MILWAUKEE factory
Service Center location or MILWAUKEE Authorized Service Station,
freight prepaid and insured, is required. A copy of the proof of purchase
should be included with the return product. This warranty does not
apply to damage that MILWAUKEE determines to be from repairs
made or attempted by anyone other than MILWAUKEE authorized
personnel, misuse, alterations, abuse, normal wear and tear, lack of
maintenance, or accidents.
Normal Wear: Many power tools need periodic parts replacement and
service to achieve best performance. This warranty does not cover
repair when normal use has exhausted the life of a part including,
but not limited to, chucks, brushes, cords, saw shoes, blade clamps,
o-rings, seals, bumpers, driver blades, pistons, strikers, lifters, and
bumper cover washers.
*This warranty does not cover Air Nailers & Staplers; Airless Paint
Sprayer; Cordless Battery Packs; Gasoline Driven Portable Power
Generators; Hand Tools; Hoist – Electric, Lever & Hand Chain;
M12™ Heated Gear; Reconditioned Product; and Test & Measure-
ment Products. There are separate and distinct warranties available
for these products.
**The warranty period for Job Site Radios, M12™ Power Port, M18™
Power Source, Jobsite Fan and Trade Titan™ Industrial Work Carts
is one (1) year from the date of purchase. The warranty period for the
Drain Cleaning Cables and AIRSNAKE™ Drain Cleaning Air Gun
Loading ...
Loading ...
Loading ...