UNIMAC TOLWDVUM3IEA 30L Wet & Dry Vacuum 3 Stage User Manual

User Manual

[Revision 4.0]

READ THIS MANUAL CAREFULLY BEFORE USE – FAILURE TO DO SO MAY RESULT IN INJURY, PROPERTY DAMAGE AND MAY

VOID WARRANTY. • KEEP THIS MANUAL FOR FUTURE REFERENCE. • Products covered by this manual may vary in

appearance, assembly, inclusions, specifications, description, and packaging.

UM-3IE 30L Industrial Wet & Dry Vacuum

E&OE © Unimac 2

Safety

Safety messages are designed to alert you to possible dangers or hazards that could cause death, injury or

equipment or property damage if not understood or followed. Safety messages have the following symbols:

You WILL be KILLED or

SERIOUSLY INJURED if you do

not follow instructions.

You CAN be KILLED or

SERIOUSLY INJURED if you do

not follow instructions.

You CAN be INJURED if you do

not follow instructions or equipment

damage may occur.

It is vital that you read and understand this

user manual before using the product,

including safety warnings, and any assembly

and operating instructions. Keep the manual

for future reference.

Safety precautions and recommendations

detailed here must be fully understood and

followed to reduce the risk of injury, fire,

explosion, electrical hazard, and/or property

damage.

Safety information presented here is generic

in nature – some advice may not be

applicable to every product. The term

"equipment" refers to the product, be it

electrical mains powered, battery powered or

combustion engine powered.

• Before Use - If you are not familiar with the

safe operation/handling of the equipment or

are in any way unsure of any aspect of

suitability or correct use for your

application, you should complete training

conducted by a person or organization

qualified in safe use and operation of this

equipment, including fuel/electrical handling

and safety.

• Do NOT operate the equipment in

flammable or explosive environments, such

as in the presence of flammable liquids,

gases, or dust. The equipment may create

sparks or heat that may ignite flammable

substances.

• Keep clear of moving parts.

• Equipment may be a potential source of

electric shock or injury if misused.

• Do NOT operate the equipment if it is

damaged, malfunctioning or is in an

excessively worn state.

• Do NOT allow others to use the equipment

unless they have read this manual and are

adequately trained.

• Keep packaging away from children - risk

of suffocation! Operators must use the

equipment correctly. When using the

equipment, consider conditions and pay

due care to persons and property.

General Work Area Safety

•

Work areas should be clean and well it.

• Do not operate the equipment if

bystanders, animals etc are within

operating range of the equipment or the

general work area.

• If devices are provided for connecting dust

extraction / collection facilities, ensure

these are connected and used properly.

Dust collection can reduce dust-related

hazards.

General Personal Safety

•

Wear appropriate protective equipment

when operating, servicing, or when in the

operating area of the equipment to help

protect from eye and ear injury, poisoning,

burns, cutting and crush injuries. Protective

equipment such as safety goggles,

respirators, non-slip safety footwear, hard

hat, hearing protection etc should be used

for appropriate equipment / conditions.

Other people nearby should also wear

appropriate personal protective equipment.

Do not wear loose clothing or jewellery,

which can be caught in moving parts. Keep

hair and clothing away from the equipment.

• Stay alert and use common sense when

operating the equipment. Do not over-

reach. Always maintain secure footing and

balance.

• Do not use the equipment if tired or under

the influence of drugs, alcohol, or

medication.

• This equipment is not intended for use by

persons with reduced physical, sensory, or

mental capabilities.

General Fuel Safety

•

Petrol/fuel/gasoline is extremely flammable

– keep clear of naked flames or other

ignition sources.

• Do not spill fuel. If you spill fuel, wipe it off

the equipment immediately – if fuel gets on

your clothing, change clothing.

• Do NOT smoke near fuel or when

refuelling.

• Always shut off the engine before

refuelling.

• Do NOT refuel a hot engine.

• Open the fuel cap carefully to allow any

pressure build-up in the tank to release

slowly.

• Always refuel in well-ventilated areas.

• Always check for fuel leakage. If fuel

leakage is found, do not start, or run the

engine until all leaks are fixed.

General Carbon-Monoxide Safety

•

Using a combustion engine indoors CAN

KILL IN MINUTES. Engine exhaust

contains carbon-monoxide – a poison you

cannot smell or see.

• Use combustion engines OUTSIDE only,

and far away from windows, doors, and

vents.

General Equipment Use and Care

•

Keep packaging away from children and

pets, potential risk of suffocation or

choking.

• The equipment is designed for domestic

use only.

• Handle the equipment safely and carefully.

• Before use, inspect the equipment for

misalignment or binding of moving parts,

loose components, damage, or any other

condition that may affect its operation. If

damaged, have the equipment repaired by

an authorised service centre or technician

before use.

• Prevent unintentional starting of the

equipment - ensure equipment and power

switches are in the OFF position before

connecting or moving equipment. Do not

carry equipment with hands or fingers

touching any controls. Remove any tools or

other items that are not a part of the

equipment from it before starting or

switching on.

• Do not force the equipment. Use the

correct equipment for your application.

Equipment will perform better and be safer

when used within its design and usage

parameters.

• Use the equipment and accessories etc. in

accordance with these instructions,

considering working conditions and the

work to be performed. Using the equipment

for operations different from those intended

could result in hazardous situations.

• Always keep equipment components

(engines, hoses, handles, controls, frames,

housings, guards etc) and accessories

(cutting tools, nozzles, bits etc) properly

maintained. Keep the equipment clean and,

where applicable, properly lubricated.

• Store the equipment out of reach of

children or untrained persons. To avoid

burns or fire hazards, let the equipment

cool completely before transporting or

storing. Never place or store the equipment

near flammable materials, combustible

gases, or liquids etc.

• The equipment is not weather-proof, and

should not be stored in direct sunlight, at

high ambient temperatures or locations that

are damp or humid.

• Do not clean equipment with solvents,

flammable liquids, or harsh abrasives.

• For specific equipment safety use and care,

see Equipment Safety.

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC `

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC

UM-3IE 30L Industrial Wet & Dry Vacuum

E&OE © Unimac 3

General Electrical Safety

•

Inspect electrical equipment, extension

cords, power bars, and electrical fittings for

damage or wear before each use. Repair or

replace damaged equipment immediately.

• Ensure all power sources conform to

equipment voltage requirements and are

disconnected before connecting or

disconnecting equipment.

• When wiring electrically powered

equipment, follow all electrical and safety

codes.

• Always use a Residual Current Device

(RCD) (GFCI) / Earth Leakage Circuit

Breaker / Safety Switch when operating this

item (electrical items only).

• High voltage / high current power lines may

be present. Use extreme caution to avoid

contact or interference with power lines.

Electrical shock can be fatal.

General Electrical Safety

•

Electrically grounded equipment must have

an approved cord and plug and be

connected to a grounded electrical outlet.

• Do NOT bypass the ON/OFF switch and

operate equipment by connecting and

disconnecting the electrical cord.

• Do NOT use equipment that has exposed

wiring, damaged switches, covers or

guards.

• Do NOT use electrical equipment in wet

conditions or in damp locations.

• Do NOT use electrical cords to lift, move or

carry equipment.

• Do NOT coil or knot electrical cords, and

ensure electrical cords are not trip hazards.

General Service Information

•

The equipment must be serviced or

repaired at authorised service centres by

qualified personnel only.

• Replacement parts must be original

equipment manufacturer (OEM) to ensure

equipment safety is maintained.

• Do NOT attempt any maintenance or repair

work not described in this manual.

• After use, the equipment and components

may still be hot – allow the equipment to

cool and disconnect spark plugs and/or

electrical power sources and/or batteries

from it before adjusting, changing

accessories, or performing repair or

maintenance.

• Do NOT adjust while the equipment is

running.

• Perform service-related activities in suitable

conditions, such as a workshop.

• Replace worn, damaged or missing

warning/safety labels immediately.

Child Choking Hazard!

• W

ARNING: CHOKING HAZARD - CHILDREN UNDER 8 YRS. CAN CHOKE OR SUFFOCATE ON SMALL PARTS. ADULT

SUPERVISION REQUIRED.

• Carefully inspect anything a baby or child could gain access to, including this product & packaging.

• Dangers include anything of a size that could become stuck or lodged in a baby or child's airway.

• Dangers include things like raw, hard fruit and vegetable pieces, large pieces of meat, bones or sausage skins, popcorn, nuts,

hard lollies and corn chips, small magnets and batteries, coins, beads, marbles and small uninflated balloons, broken toys and smaller toys,

buttons, keys, and coins. But there are also many more.

• Pay particular attention to accessories, nuts, bolts, screws, washers, caps, covers, loose parts, parts that could be removed or break off, pieces

of packaging, staples, tape etc.

• In the case of any doubt, secure the item of concern in an appropriate manner, or completely remove the possibility of access by a baby or child.

General Safety Considerations

•

KNOW YOUR TOOL. Read and understand this manual and labels affixed to the tool. Learn its application and limitations as well as its specific

potential hazards.

• GROUND THE TOOL. This tool is equipped with an approved 3- conductor cord and a 3- prong grounding type plug to fit the proper grounding

type receptacle. The green conductor in the cord is the grounding wire. NEVER connect the green wire to a live terminal.

• KEEP GUARDS IN PLACE. Keep in good working order, property adjusted and aligned.

• REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before

turning it on.

• KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents. Make sure the floor is clean and not slippery.

• AVOID DANGEROUS ENVIRONMENT. Don’t use power tools in damp or wet locations or expose them to rain. Keep work area well-lit and

provide adequate surrounding work space.

• KEEP CHILDREN AWAY. All visitors should be kept a safe distance from work area.

• MAKE WORKSHOP CHILD- PROOF with padlocks, master switches or by removing starter keys.

• USE PROPER SPEED. A tool will do a better and safer job when operated at the proper speed.

• USE RIGHT TOOL. Don’t force the tool or the attachment to do a job for which it was not designed.

• WEAR PROPER APPAREL. Do not wear loose clothing, gloves, neckties, or jewellery (rings, watch) because they could get caught in moving

parts. Non- slip footwear is recommended. Wear protective hair covering to contain long hair. Roll up long sleeves above the elbows.

• ALWAYS WEAR SAFETY GLASSES.

• DON'T OVERREACH. Keep proper footing and balance at all times.

• MAINTAIN TOOL WITH CARE. Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating and changing

accessories.

• DISCONNECT TOOLS. Before servicing, when changing accessories or attachments.

• AVOID ACCIDENTAL STARTING. Make sure the switch is in the "OFF" position before plugging in.

• USE RECOMMENDED ACCESSORIES. Consult the manual for recommended accessories. Follow the instructions that accompany the

accessories. The use of improper accessories may cause hazards.

• NEVER STAND ON TOOL. Serious injury could occur if the tool tips over. Do not store materials such that it is necessary to stand on the tool to

reach them.

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC `

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC

UM-3IE 30L Industrial Wet & Dry Vacuum

E&OE © Unimac 4

• CHECK DAMAGED PARTS. Before further use of the tool, a guard or other parts that are damaged should be carefully checked to ensure that

they will operate properly and perform their intended function. Check for alignment of moving parts, breakage of parts, mounting, and any other

conditions that may affect its operation. A guard or other parts that are damaged should be properly repaired or replaced.

• NEVER LEAVE MACHINE RUNNING UNATTENDED. Turn power “OFF”. Don’t leave any tool running until it comes to a complete stop.

Specific Safety Rules for Dust Extractor Wet/Dry Vacuum

•

Safety is a combination of common sense, staying alert and knowing how your vacuum works. Read and understand the following safety rules

before operating.

• For your own safety, read the entire instruction manual before operating this vacuum.

• Wear personal protective equipment. Depending on application, use face shield, safety goggles or safety glasses. Where appropriate, wear dust

mask, hearing protectors, gloves, and workshop apron capable of stopping small abrasive or workpiece fragments. The safety glasses must be

capable of protecting against flying particles generated by the various operations.

• Operate the vacuum cleaner only using grounded outlets that are according to regulations.

• Only use undamaged power cords and regularly check condition of extension cords.

• When wet vacuuming, operate the vacuum cleaner only when the container is level, otherwise there is danger of electric shock from water

penetrating into the vacuum cleaner's motor.

• Do NOT expose to rain, this vacuum must be stored indoors.

• Do not handle the electrical plug or vacuum with wet hands.

• Never use this vacuum with any opening blocked, keep opening free of dust, hair, lint, or anything that will restrict air flow.

• Never vacuum anything that is on fire, burning or smoking such as matches, cigarettes or hot ashes. Never vacuum flammable or combustible

liquids such as gasoline, electrical devices could produce sparks which can cause a fire or explosion! Never vacuum toxic or hazardous

materials.

• Never use this vacuum without dust bag and/or filters installed.

• Never vacuum coal ash, cement or drywall dust without the HEPA filter and dust bag installed and water is placed in the reservoir (3 stage

filtration) or you could damage the motor or the material could be exhausted back into the air. The replacement HEPA and High Efficiency filters

and accessories are available and are listed in the parts list.

• WARNING! ALL ELECTRICAL CONNECTIONS MUST BE DONE BY A QUALIFIED ELECTRICIAN. FAILURE TO COMPLY MAY RESULT IN

SERIOUS INJURY! ALL ADJUSTMENTS OR REPAIRS MUST BE DONE WITH THE MACHINE DISCONNECTED FROM THE POWER

SOURCE. FAILURE TO COMPLY MAY RESULT IN SERIOUS INJURY!

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC `

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC

UM-3IE 30L Industrial Wet & Dry Vacuum

E&OE © Unimac 5

Safety Symbols

The product may have safety warning labels attached to it, explained below. Understand the symbols on your

product and their meanings. If any stickers become unreadable, unattached etc., replace them.

Flammable Material Hazard

Flammable liquids, gases, or

substances etc may present.

Avoid ignition sources and open

flames. Danger of fire.

Read User Manual

Read and fully understand

product safety warnings,

operation, procedures etc before

using the product.

Use Hand Protection

Wear appropriate hand protection

and take due care as the product

or use of the product may present

hand hazards.

Carbon-Monoxide Hazard

Do not use the product in

confined areas or without

adequate ventilation. Carbon-

monoxide poisoning can be fatal.

Electrocution / Electrical Shock

Hazard

High voltage or high current

electricity may be present or

required by the product. Take

due care when handling electrical

products, cables, plugs and

leads. Electrical shock can be

fatal.

Toxic Fumes / Dust Hazard

Using the product or by-products

from use may produce fumes,

smoke or particles that could be

harmful if inhaled. Wear

appropriate breathing protection

and have adequate ventilation.

Explosive Material Hazard

Combustible liquids, gases, or

substances etc may be present.

Avoid ignition sources and open

flames. Danger of explosion.

Cutting / Amputation Hazard

The product may have blades,

edges or mechanical devices that

can cause severe cut injury to

fingers, limbs etc. Take due care

when handling and using the

product.

Crush Hazard

The product may have blades,

edges or mechanical devices that

can cause severe crush injury to

fingers, limbs etc. Take due care

when handling and using the

product.

Single Operator Only

The product must be operated by

a single person only. More than

one person operating the product

may introduce additional hazards.

Use Face Protection

Wear appropriate full-face

protection and take due care as

the product or use of the product

may present face and eye

hazards.

Use Foot Protection

Wear appropriate foot protection

and take due care as the product

or use of the product may present

foot hazards.

Use Eye / Ear / Head Protection

Wear appropriate eye and / or

ear and / or head protection and

take due care as the product or

use of the product may present

eye, hearing, and head hazards.

Running Hazard

Do not run on or near the product

as doing so may present a fall

hazard.

Diving Hazard

Do not dive into the product as

doing so may present a neck /

head injury hazard.

Adult Supervision Required

Always supervise children and

other users of a product to

prevent drowning or injury.

Skin Penetration / Puncture

Hazard

The product may produce

pressure, emit liquids or objects

that can cause severe injury to

fingers, limbs, blood etc. Take

due care when handling and

using the product.

Hot Surface Hazard

Be aware that the product may

produce high temperatures and

hot surfaces that can cause burn

injuries.

Flying Debris Hazard

Be aware that the product or use

of the product may present

hazards produced by flying

debris. Wear appropriate clothing

and protective devices.

Moving Parts Hazard

Be aware that the product

contains or uses mechanical

devices that move or rotate.

Always wait for moving parts to

stop fully before handling the

product, adjusting, maintenance

etc.

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC `

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC

UM-3IE 30L Industrial Wet & Dry Vacuum

E&OE © Unimac 6

Carbon-Monoxide Hazard

Do not use the product in

confined areas or without

adequate ventilation. Carbon-

monoxide poisoning can be fatal.

Pull Hazard

Be aware that the product

contains or uses mechanical

devices that can pull in objects

and can cause severe injury to

fingers, limbs etc. Take due care

when handling and using the

product.

Slope / Fall Injury Hazard

Be aware that using the product

on sloping surfaces or in slippery

conditions may present additional

dangers from falls and contact

with blades, moving parts, hot

surfaces etc.

"Slam Dunk" Warning

Do NOT attempt "slam dunk"

manoeuvres as this may result in

severe injury due to falling,

product breakage or collapse etc.

Electrocution / Electrical Shock

Hazard - Outdoor

High voltage or high current

electricity may be present or

required by the product. Do NOT

use in rain, damp, or wet

conditions. Electrical shock can

be fatal.

Electrocution / Electrical Shock

Hazard - Disconnect

High voltage or high current

electricity may be present or

required by the product. Always

disconnect the product from the

electrical supply before handling

the product, adjusting,

maintenance etc.

Power Line Electrocution

Hazard

High voltage / high current power

lines may be present. Use

extreme caution to avoid contact

or interference with power lines.

Electrical shock can be fatal.

"Kick-Back" Hazard

High level of "kick-back" hazard

that can cause the machine to

suddenly rotate towards operator.

Kick-back injury can be fatal.

Winch Operator Position

Hazard

Do NOT stand between winch

and load. Do NOT use winch to

move people.

Winch Lift Hazard

Do NOT LIFT load vertically. Use

machine to PULL only.

Cable Hazard

Ensure that load bearing cable is

not kinked or knotted.

Winch Cable Hazard

Ensure that there is a minimum

number of cable coils on

winching mechanism.

Winch Hook Hazard

Carry hook to load – do NOT

throw or run.

Flash / Blinding Hazard

Wear appropriate eye protection

for welding. Direct exposure to

weld arcs may cause permanent

eye injury.

Laser Hazard

Laser may be in use – do NOT

look directly at laser or allow

others to.

Choking Hazard

Children under 8 yrs. Can choke

or suffocate on small parts. Adult

supervision required.

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC `

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC

UM-3IE 30L Industrial Wet & Dry Vacuum

E&OE © Unimac 7

Table of Contents

Safety ............................................................................................................................................................. 2

Safety Symbols ........................................................................................................................................................... 5

Parts Identification ....................................................................................................................................... 8

Assembly ....................................................................................................................................................... 9

Installing the Correct Filter and / or Dust Bag for The Application ............................................................................. 9

When Vacuuming Dry Materials - 3 Stage Dry Filtration (Water filtration only) ......................................................... 9

Stage Dry Filtration (Regular Dry Cleaning) ............................................................................................................. 10

When Vacuuming Wet Materials (Foam Filter) ........................................................................................................ 11

Hose, Wand and Accessory Assembly ..................................................................................................................... 12

Operation ..................................................................................................................................................... 13

Turning The Vacuum ON/OFF / Tool Triggered Mode ............................................................................................. 13

Variable Speed Adjustment ...................................................................................................................................... 13

Tool Triggered Function- 220-240V Power Tool & Air Tool Synchro ....................................................................... 14

220-240V Power Tool Triggered Synchro - 3 Stage Dry Filtration ........................................................................... 14

Tool Triggered Function- 220-240V Power Tool & Air Tool Synchro Air Tool Triggered Synchro - 3 Stage Dry

Filtration .................................................................................................................................................................... 15

Air Blower & Manual Self-Clean (Reverse Air) Function .......................................................................................... 16

Water Level Self-Stop (When Vacuuming Wet Materials)........................................................................................ 16

Maintenance ................................................................................................................................................ 17

Regular Maintenance................................................................................................................................................ 17

Cleaning .................................................................................................................................................................... 17

Storage ..................................................................................................................................................................... 18

Specifications ............................................................................................................................................. 19

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC `

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC

UM-3IE 30L Industrial Wet & Dry Vacuum

E&OE © Unimac 8

Parts Identification

No. Name No. Name No. Name

A Caster wheels I Variable speed dial Q Foam filter

B Wet vacuuming hose inlet J Variable speed dial R HEPA filter (pre-assembled)

C Flexible hose K On/Off switch S Crevice tool

D

Extendable wand

L

240V Power tool synchro plug

T

Dust suction adapter

E

Power cord wrap posts

M

Inlet cover

U

Arch brush

F Pivot handle N Clear inlet cover V

Non-woven bag (upper +

lower)

G

30L tank

O

Air tool synchro air inlet/outlet

H Floor sweep P

Dry vacuuming 3 stage

filtration hose inlet

Spare parts available

for purchase, scan QR

code below:

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC `

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC

UM-3IE 30L Industrial Wet & Dry Vacuum

E&OE © Unimac 9

Assembly

WARNING! TO REDUCE THE POTENTIAL FOR PERSONAL

INJURY AND/OR DAMAGE TO THE MACHINE, BEFORE

ASSEMBLING MAKE SURE THE MACHINE IS TURNED OFF

AND THE PLUG IS NOT CONNECTED TO A POWER SOURCE.

DO NOT TURN ON OR PLUG IN THE MACHINE UNTIL

INSTRUCTED TO DO SO AFTER ALL ASSEMBLY STEPS IN

THIS MANUAL HAVE BEEN COMPLETED.

Installing the Correct Filter and / or

Dust Bag for The Application

Before every operation, it is important to determine the desired

cleaning application, WET or 3 STAGE DRY filtration vacuuming.

Each cleaning application requires different accessories to be

installed, and the hose needs to be connected to the appropriate

inlet (Front inlet = Wet/Top inlet = 3 Stage Dry Filtration).

When Vacuuming Dry Materials - 3

Stage Dry Filtration (Water filtration

only)

To ensure proper filtration of fine or drywall dust, set up the

vacuum for 3 stages dry filtration as described below.

STAGE 1 - Dust bag

1. The cloth dust bag (A) Fig. 4 must be installed to the clear

cover (B) on the top of the vacuum as shown. If the dust bag is

not installed, push clear cover latch (C) Fig. 4, and remove

clear cover.

2. Install the dust bag (A) Fig. 5 to the clear cover (B), place

sections A together; lock dust bag using the spring latch (C).

Reinstall clear cover.

STAGE 2 - Water filtration

3. Unlatch the cover/motor assembly latches (A) Fig. 6 on both

sides of the tank. Lift and place the cover/motor assembly on

its side.

4. Fill the tank (A) Fig. 7 with water, do not fill it past the

maximum "Water level" marking (B) as shown.

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC `

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC

UM-3IE 30L Industrial Wet & Dry Vacuum

E&OE © Unimac 10

STAGE 3 - HEPA Filter or High Efficiency Filter

5. For dry vacuuming of drywall or cement dust, make sure the

HEPA filter (A) Fig. 8 is installed as shown.

If the incorrect filter is installed, simply pull it out and slide the

HEPA filter into place until it is secured to the housing as

shown.

6. Reposition and secure the cover/motor assembly to the tank

with both cover latches.)

7. For all 3 stage dry filtration operations, the "flexible hose (A)

Fig. 9 MUST be installed to the top inlet (B) located on top of

the clear cover (C). Remove inlet cover (D) and reinstall it in

the front inlet. Insert the flexible hose (A) into the top inlet (B)

and turn it clockwise until it locks.

The vacuum Is now ready for 3 STAGE DRY

FILTRATION.

Stage Dry Filtration (Regular Dry

Cleaning)

STAGE 1 - Dust bag

The cloth dust bag (a) Fig.4A must be properly installed to the

suction port (b) on the tank of the vacuum, as shown.

STAGE2 - HEPA Filter or High Efficiency Fitter (Figure. 8)

STAGE3 - Install Hose

The flexible hose (A) Fig. 11 MUST be installed to the front inlet (B) located on the front of the vacuum. Remove

inlet cover (C) and reinstall it in the top inlet.

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC `

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC

UM-3IE 30L Industrial Wet & Dry Vacuum

E&OE © Unimac 11

When Vacuuming Wet Materials (Foam Filter)

1. For vacuuming wet materials, and to ensure proper filtration, the black foam filter (A) Fig. 10 must be

installed. Unlatch the cover/motor assembly latches (A) Fig. 6 on both sides of the tank. Lift and place the

cover/motor assembly on its side, slide the foam filter (A) Fig. 10 into the housing as shown.

2. Reposition and secure the cover/motor assembly to the tank with both cover latches.

3. For all wet filtration operations, the flexible hose (A) Fig. 11 MUST be installed to the front inlet (B) located

on the front of the vacuum. Remove inlet cover (C) and reinstall it in the top inlet insert the flexible hose (A)

into the front inlet (B) and turn it clockwise until it locks.

Note: Before vacuuming wet materials, make sure there Is no water Inside the tank. When finished

vacuuming wet materials, empty and clean tank.

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC `

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC

UM-3IE 30L Industrial Wet & Dry Vacuum

E&OE © Unimac 12

Hose, Wand and Accessory Assembly

Note: At this point, the flexible hose has already been installed into the appropriate Inlet (front for Wet

materials, or top for 3 Stage Dry Filtration) and the Inlet cover has been Installed in the Inlet which is not

being used.

1. Slide the end of the hose (A) Fig. 12 into the extension wand (B) as shown.

2. Attach either the floor brush (C) Fig. 12, crevice tool or arch brush to the other end of the extension wand

(B).

3. The extension wand does not need to be used, the floor sweep, crevice tool or brush tool can also be

installed to the end of the flexible hose.

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC `

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC

UM-3IE 30L Industrial Wet & Dry Vacuum

Operation

Turning The Vacuum ON/OFF / Tool

Triggered Mode

This Dust Extractor Vacuum comes with an ON/OFF / Tool Triggered dust-

proof toggle switch (A) Fig. 13. To turn the vacuum ON, press the toggle

switch upwards. To turn the vacuum OFF, press the toggle switch to the

middle position. To activate the tool triggered feature, press the toggle

switch downwards.

Variable Speed Adjustment

1. This Dust Extractor Vacuum comes with a variable speed dial (B) Fig. 13 which controls the speed of the

motor, which in turn increases or decreases the suction capacity of the vacuum.

2. Turn variable speed dial clockwise to increase suction capacity or turn counterclockwise to decrease suction

capacity.

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC `

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC

UM-3IE 30L Industrial Wet & Dry Vacuum

Tool Triggered Function- 220-240V

Power Tool & Air Tool Synchro

Note: This Dust Extractor Vacuum comes with two methods

of automatically turning on the vacuum when a tool is

activated. The following instructions describe the 220-240V

Power Tool Triggered Synchro function and the Air Tool

Triggered Synchro function.

220-240V Power Tool Triggered

Synchro - 3 Stage Dry Filtration

This function can only be used for 3 Stage Dry Filtration, to use

the 220 - 240V Power Tool Triggered Synchro function:

1. Set-up the vacuum for 3 Stage Dry Filtration as described in

the section "When Vacuuming Dry Materials (3 S

tage Dry

Filtration)" Figures 4-9.

2. Select the power tool to use, then use the supplied hose or

other fittings necessary to connect the dust collection port of

the power tool to the flexible hose of the vacuum.

WARNING! The maximum permissible power tool power is

800W. The available amperage rating Is determined by the

speed of the motor. The maximum power will be less than

800W If operated at full speed. If the power tool trips the

circuit, reduce the speed of the motor using the variable

speed dial and try again.

3. Connect the power tool power cord (A) Fig. 14 into the 220-

240V socket (B) as shown.

4. Press the toggle switch (A) Fig. 13 downwards to the Tool

Triggered position. The vacuum will not tum on. The vacuum

goes into standby mode until the power tool is activated.

5. Turn the power tool ON, the vacuum will automatically start.

Tum the power tool Off, the vacuum will automatically stop

after a few seconds to clear the debris from the hose.

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC `

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC

UM-3IE 30L Industrial Wet & Dry Vacuum

Tool Triggered Function- 220-240V Power Tool & Air Tool

Synchro Air Tool Triggered Synchro - 3 Stage Dry Filtration

This function can only be used for 3 Stage Dry Filtration. To use the Air Tool Triggered Synchro function:

1. Set-up the vacuum for 3 Stage Dry Filtration as described in the section When Vacuuming Dry Materials (3

Stage Dry Filtration) Figures 4-9.

2. Select the air tool to use, then using the supplied hose or other fittings necessary to connecting the dust

collection port of the air tool to the flexible hose of the vacuum.

3. Connect an air hose to your air compressor, connect the other end of the air hose (A) Fig. 15 as shown. The

air hose must have a quick connect fitting, connect the quick connect fitting to the air inlet as shown.

4. Connect another air hose to your air tool, connect the other end of the air hose (B) Fig. 15 as shown. The air

hose must have an air inlet, connect this fitting to the quick connect fitting (C) as shown.

5. Press the toggle switch (A) Fig. 13 downwards to the Tool Triggered position. The vacuum will not turn on,

the vacuum goes into standby mode until the air tool is activated.

6. Activate the air tool, the vacuum will automatically start. Deactivate the air tool, the vacuum will automatically

stop after a few seconds to clear the debris from the hose.

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC `

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC

UM-3IE 30L Industrial Wet & Dry Vacuum

Air Blower & Manual Self-Clean (Reverse Air) Function

This Vacuum can be used as a blower. To use the Dust Extractor blower function:

•

This vacuum comes with an air outlet (A) Fig. 16, which can be used as a blower. Simply insert the flexible

hose (B) into the air outlet and turn it clockwise until it locks. The hose can now be used as a blower.

This Dust extractor Vacuum also comes with a convenient reverse air manual self-clean feature which cleans

the installed Filter. After a period, the filter may become very dirty and the suction capacity may be reduced,

using the manual self-clean feature will clean the filter and improve the suction capacity. To use the manual self-

clean function:

With the flexible hose installed in the front inlet or the top inlet, and the vacuum turned on, position the end on

the hose (A) Fig. 17 onto the depress button (B). Press down and release, repeat step 3-5 times.

Water Level Self-Stop (When Vacuuming Wet Materials)

This Dust extractor Vacuum comas with a convenient water level self-stop feature. When vacuuming wet

materials, once the tank water level reaches the maximum permissible amount, the vacuum will automatically

stop.

When this happens, the tank must be emptied of its dirty water. Turn the vacuum Off, empty tank and restart.

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC `

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC

UM-3IE 30L Industrial Wet & Dry Vacuum

Maintenance

WARNING! TO REDUCE THE POTENTIAL FOR PERSONAL INJURY MAKE SURE THE VACUUM IS

TURNED OFF AND HAS BEEN UNPLUGGED BEFORE PERFORMING ANY PERIODIC MAINTENANCE

OPERATIONS.

Regular Maintenance

To ensure optimum performance and longer service life of your

Dust extractor wet/dry vacuum, the following basic maintenance

steps should be practiced regularly:

•

Inspect the power cord and plug for damage before each use.

Never operate the Dust extractor wet/dry vacuum with a

damaged power cord or plug. To reduce the risk of electric

shock, unexpected start-up, and /or damage to the motor

replace a damaged power cord or plug Immediately.

•

Test the ON/OFF switch before each use. Never operate the

Dust extractor wet/dry vacuum with a

damaged/malfunctioning switch. To reduce the risk of electric

shock, unexpected start-up, and/or damage to the motor,

replace a damaged/malfunctioning switch immediately.

Cleaning

Cleaning the Filters

The HEPA and High Efficiency filters can be cleaned by passing

compressed air through the filter. Eventually no amount of

cleaning will help, and the filter will need to be replaced.

Cleaning the cloth dust bag

1. When the dust bag (A) Fig. 18 gets close to being full it should be emptied and cleaned.

2. Slide and remove the plastic retainer (B) Fig.18 from the dust bag and empty contents of dust bag.

3. Once empty the dust bag can be cleaned with warm water, it is recommended to turn dust bag inside out

during the cleaning process. Let dust bag dry before installing.

4. Reinstall the plastic retainer at the bottom of the dust bag, reinstall dust bag.

Cleaning the tank

It is important to keep the inside of the tank clean between Wet vacuuming and Dry vacuuming operations. To

empty tank, simply remove top cover/motor assembly and tilt tank to empty water. Clean tank thoroughly.

Cleaning the water connector pipe

1. During 3 Stage Dry Filtration, the white connector pipe (A) Fig.19 gets dirty and will need periodic cleaning.

2. Unlatch the cover/motor assembly latches on both sides of the tank. Lift and place the cover/motor assembly

on its side.

3. Slide the connector pipe (A) off the housing and clean with clean water. Reinstall connector pipe once

cleaned.

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC `

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC

UM-3IE 30L Industrial Wet & Dry Vacuum

Storage

Before storing vacuum:

Make sure the vacuum has been completely cleaned. Wrap the power cord (A) Fig.20 around the power cord

posts and lower handle as shown. Vacuum is ready for storage.

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC `

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC

UM-3IE 30L Industrial Wet & Dry Vacuum

Specifications

Power (HP) 1600W

Input Voltage 240V

Frequency 50/60Hz

Suction 19 Kpa

Air Hose Outlet 1/4 Nitto style connector

Power Cord Length 4.5m

Tank Capacity 30L

Hose Diameter 32mm

Airflow Volume 35L/s

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC `

UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC UNIMAC

Some experts believe that the incorrect or prolonged use of almost any

product may cause serious injury or death. To help reduce your risk of

serious injury or death, refer to the information below. For more information,

see www.datastreamserver.com/safety



Consult all documentation, packaging,

and product labelling before use. Note

that some products feature

documentation available online. It is

recommended to print and retain the

documentation.



Before each use, check the product for

loose/broken/damaged/missing parts,

wear, or leaks (if applicable). Never use a

product with

loose/broken/damaged/missing parts,

wear, or leaks.



Products must be inspected and serviced

(if applicable) by a qualified technician

every 6 months. This is based on

average residential use by persons of

average size and strength, and on a

property of average metropolitan size.

Use beyond these recommendations may

require more frequent

inspections/servicing.



Ensure that all users of the product have

completed a suitable industry recognised

training course before being allowed

access to the product.



The product has been supplied by a general merchandise

retailer that may not be familiar with your specific

application or description of application. Be sure to attain

third-party approval from a qualified specialist for your

application before use, regardless of any assurances from

the retailer or its representatives.



This product is not intended for use where fail-safe

operation is required. As with any product (for example,

automobile, computer, toaster), there is the possibility of

technical issues that may require the repair or

replacement of parts, or the product itself. If the possibility

of such failure and the associated time it may take to

rectify could in any way inconvenience the user, business,

or employee, or financially affect the user, business, or

employee, then the product is not suitable for your

requirements. This product is not intended for use where

incorrect operation or a failure of any kind, including but

not limited to, a condition requiring product return,

replacement, parts replacement, or service by a

technician may cause financial loss, loss of employee

time or an inconvenience requiring compensation.



If this product has been purchased in error when

considering the information presented here, contact the

retailer directly for details of their returns policy, if

required.

diagrams, or images may be reproduced or transmitted in any form or by any means, electronic or

mechanical, including photocopying, scanning, or recording, or any information storage and retrieval system,

without express permission or consent from the publisher.

UNIMAC TOLWDVUM3IEA 30L Wet & Dry Vacuum 3 Stage Filtration, Water & HEPA Filter, Powerful Air Pass-through & Accessories

Product's Documents

Product manual

Specifications

UNIMAC TOLWDVUM3IEA Questions and Answers