BAUMR-AG TOLWDVBM2SLA Cordless Wet & Dry Vacuum Cleaner Kit User Manual

BM-2SL 20L Wet & Dry Vacuum

User Manual

[Revision 2.0]

READ THIS MANUAL CAREFULLY BEFORE USE – FAILURE TO DO SO MAY RESULT IN INJURY, PROPERTY DAMAGE AND

MAY VOID WARRANTY. • KEEP THIS MANUAL FOR FUTURE REFERENCE. • Products covered by this manual may vary in

appearance, assembly, inclusions, specifications, description, and packaging.

THE BATTERY MAY HAVE SOME CHARGE ON ARRIVAL, IT IS IMPORTANT

HOWEVER THAT THE BATTERY IS CHARGED PRIOR TO USE.

BM-2SL 20L Wet & Dry Vacuum

E&OE © Baumr-AG 2

Safety

Safety messages are designed to alert you to possible dangers or hazards that could cause death, injury or

equipment or property damage if not understood or followed. Safety messages have the following symbols:

You WILL be KILLED or

SERIOUSLY INJURED if you do

not follow instructions.

You CAN be KILLED or

SERIOUSLY INJURED if you do

not follow instructions.

You CAN be INJURED if you do

not follow instructions or equipment

damage may occur.

It is vital that you read and understand this

user manual before using the product,

including safety warnings, and any assembly

and operating instructions. Keep the manual

for future reference.

Safety precautions and recommendations

detailed here must be fully understood and

followed to reduce the risk of injury, fire,

explosion, electrical hazard, and/or property

damage.

Safety information presented here is generic

in nature – some advice may not be

applicable to every product. The term

"equipment" refers to the product, be it

electrical mains powered, battery powered or

combustion engine powered.

• Before Use - If you are not familiar with the

safe operation/handling of the equipment or

are in any way unsure of any aspect of

suitability or correct use for your

application, you should complete training

conducted by a person or organization

qualified in safe use and operation of this

equipment, including fuel/electrical handling

and safety.

• Do NOT operate the equipment in

flammable or explosive environments, such

as in the presence of flammable liquids,

gases, or dust. The equipment may create

sparks or heat that may ignite flammable

substances.

• Keep clear of moving parts.

• Equipment may be a potential source of

electric shock or injury if misused.

• Do NOT operate the equipment if it is

damaged, malfunctioning or is in an

excessively worn state.

• Do NOT allow others to use the equipment

unless they have read this manual and are

adequately trained.

• Keep packaging away from children - risk

of suffocation! Operators must use the

equipment correctly. When using the

equipment, consider conditions and pay

due care to persons and property.

General Work Area Safety

•

Work areas should be clean and well it.

• Do not operate the equipment if

bystanders, animals etc are within

operating range of the equipment or the

general work area.

• If devices are provided for connecting dust

extraction / collection facilities, ensure

these are connected and used properly.

Dust collection can reduce dust-related

hazards.

General Personal Safety

•

Wear appropriate protective equipment

when operating, servicing, or when in the

operating area of the equipment to help

protect from eye and ear injury, poisoning,

burns, cutting and crush injuries. Protective

equipment such as safety goggles,

respirators, non-slip safety footwear, hard

hat, hearing protection etc should be used

for appropriate equipment / conditions.

Other people nearby should also wear

appropriate personal protective equipment.

Do not wear loose clothing or jewellery,

which can be caught in moving parts. Keep

hair and clothing away from the equipment.

• Stay alert and use common sense when

operating the equipment. Do not over-

reach. Always maintain secure footing and

balance.

• Do not use the equipment if tired or under

the influence of drugs, alcohol, or

medication.

• This equipment is not intended for use by

persons with reduced physical, sensory, or

mental capabilities.

General Fuel Safety

•

Petrol/fuel/gasoline is extremely flammable

– keep clear of naked flames or other

ignition sources.

• Do not spill fuel. If you spill fuel, wipe it off

the equipment immediately – if fuel gets on

your clothing, change clothing.

• Do NOT smoke near fuel or when

refuelling.

• Always shut off the engine before

refuelling.

• Do NOT refuel a hot engine.

• Open the fuel cap carefully to allow any

pressure build-up in the tank to release

slowly.

• Always refuel in well-ventilated areas.

• Always check for fuel leakage. If fuel

leakage is found, do not start, or run the

engine until all leaks are fixed.

General Carbon-Monoxide Safety

•

Using a combustion engine indoors CAN

KILL IN MINUTES. Engine exhaust

contains carbon-monoxide – a poison you

cannot smell or see.

• Use combustion engines OUTSIDE only,

and far away from windows, doors, and

vents.

General Equipment Use and Care

•

The equipment is designed for domestic

use only.

• Handle the equipment safely and carefully.

• Before use, inspect the equipment for

misalignment or binding of moving parts,

loose components, damage, or any other

condition that may affect its operation. If

damaged, have the equipment repaired by

an authorised service centre or technician

before use.

• Prevent unintentional starting of the

equipment - ensure equipment and power

switches are in the OFF position before

connecting or moving equipment. Do not

carry equipment with hands or fingers

touching any controls. Remove any tools or

other items that are not a part of the

equipment from it before starting or

switching on.

• Do not force the equipment. Use the

correct equipment for your application.

Equipment will perform better and be safer

when used within its design and usage

parameters.

• Use the equipment and accessories etc. in

accordance with these instructions,

considering working conditions and the

work to be performed. Using the equipment

for operations different from those intended

could result in hazardous situations.

• Always keep equipment components

(engines, hoses, handles, controls, frames,

housings, guards etc) and accessories

(cutting tools, nozzles, bits etc) properly

maintained. Keep the equipment clean and,

where applicable, properly lubricated.

• Store the equipment out of reach of

children or untrained persons. To avoid

burns or fire hazards, let the equipment

cool completely before transporting or

storing. Never place or store the equipment

near flammable materials, combustible

gases, or liquids etc.

• The equipment is not weather-proof, and

should not be stored in direct sunlight, at

high ambient temperatures or locations that

are damp or humid.

• Do not clean equipment with solvents,

flammable liquids, or harsh abrasives.

• For specific equipment safety use and care,

see Equipment Safety.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

BM-2SL 20L Wet & Dry Vacuum

E&OE © Baumr-AG 3

General Electrical Safety

•

Inspect electrical equipment, extension

cords, power bars, and electrical fittings for

damage or wear before each use. Repair or

replace damaged equipment immediately.

• Ensure all power sources conform to

equipment voltage requirements and are

disconnected before connecting or

disconnecting equipment.

• When wiring electrically powered

equipment, follow all electrical and safety

codes.

• Always use a Residual Current Device

(RCD) (GFCI) / Earth Leakage Circuit

Breaker / Safety Switch when operating this

item (electrical items only).

• High voltage / high current power lines may

be present. Use extreme caution to avoid

contact or interference with power lines.

Electrical shock can be fatal.

General Electrical Safety

•

Electrically grounded equipment must have

an approved cord and plug and be

connected to a grounded electrical outlet.

• Do NOT bypass the ON/OFF switch and

operate equipment by connecting and

disconnecting the electrical cord.

• Do NOT use equipment that has exposed

wiring, damaged switches, covers or

guards.

• Do NOT use electrical equipment in wet

conditions or in damp locations.

• Do NOT use electrical cords to lift, move or

carry equipment.

• Do NOT coil or knot electrical cords, and

ensure electrical cords are not trip hazards.

General Service Information

•

The equipment must be serviced or

repaired at authorised service centres by

qualified personnel only.

• Replacement parts must be original

equipment manufacturer (OEM) to ensure

equipment safety is maintained.

• Do NOT attempt any maintenance or repair

work not described in this manual.

• After use, the equipment and components

may still be hot – allow the equipment to

cool and disconnect spark plugs and/or

electrical power sources and/or batteries

from it before adjusting, changing

accessories, or performing repair or

maintenance.

• Do NOT adjust while the equipment is

running.

• Perform service-related activities in suitable

conditions, such as a workshop.

• Replace worn, damaged or missing

warning/safety labels immediately.

Child Choking Hazard!

• W

ARNING: CHOKING HAZARD - CHILDREN UNDER 8 YRS. CAN CHOKE OR SUFFOCATE ON SMALL PARTS. ADULT

SUPERVISION REQUIRED.

• Carefully inspect anything a baby or child could gain access to, including this product & packaging.

• Dangers include anything of a size that could become stuck or lodged in a baby or child's airway.

• Dangers include things like raw, hard fruit and vegetable pieces, large pieces of meat, bones or sausage skins, popcorn, nuts,

hard lollies and corn chips, small magnets and batteries, coins, beads, marbles and small uninflated balloons, broken toys and smaller toys,

buttons, keys, and coins. But there are also many more.

• Pay particular attention to accessories, nuts, bolts, screws, washers, caps, covers, loose parts, parts that could be removed or break off, pieces

of packaging, staples, tape etc.

• In the case of any doubt, secure the item of concern in an appropriate manner, or completely remove the possibility of access by a baby or child.

Important Safety Instructions

•

For your safety: carefully read and understand all instructions, this appliance complies with mandatory safety regulations for electrical equipment.

However, improper use will harm persons and property, please read these instructions carefully.

• When using electrical appliances, you must follow basic precautions.

• Do not allow other uses and unattended operation.

• Do not use the air outlet directly against people or animals when using this product.

• The manufacturer cannot be liable for damages due to improper use or improper operation.

• Do not inhale flammable, toxic liquids, such as gasoline, oil, acids, or other volatile substances, to avoid dangerous hazards.

• Only relevant professionals can repair electrical equipment. Improper repairs may result in considerable risk.

• Do not store the appliance directly at high temperatures such as hot stoves or heat sinks.

• Do not use a cleaning agent or detergent containing solvent.

• Unauthorized parts or third-party accessories may be dangerous and make the warranty invalid.

• Always check whether the float is normal.

• If you notice that liquid leaks from your equipment, immediately turn it off.

• Do not use the appliance in wet/damp locations.

• Do not inhale hot dust ashes or sharp objects.

• Do not touch the motor directly when blowing. Keep children away while operating the vacuum. Wear safety goggles.

• Do not reverse the vacuum cleaner, causing damage to the motor.

• The hose cannot be overly bent and forced to elongate, otherwise the hose will be deformed or damaged.

• Do not allow the lid part to get wet with water or rinse with water to prevent water from entering the electronic parts. If there is leakage, the proper

operation is to gently wipe the surface with a soft rag.

• The vacuum cleaner can only use the specified battery pack. If other battery packs are used, it will not be covered by the warranty if an accident

occurs.

• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of

experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the

hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

• The appliance is only to be used with the power supply unit provided with the appliance. The appliance is only to be used with the battery pack

provided with the appliance.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

BM-2SL 20L Wet & Dry Vacuum

E&OE © Baumr-AG 4

• Exhausted batteries are to be removed from the appliance and safely disposed of.

• If the appliance is to be stored unused for a long period, the batteries should be removed.

• The supply terminals are not to be short-circuited.

• Li-ion battery should be charged under an ambient temperature specified by the battery user instruction, an environment with a low (e.g. below

0˚C) or high (e.g. above 45˚C) temperature could cause serious battery safety problem.

• Remove the battery and dispose of it according to local regulations when disposing of this product.

Disposal of battery

•

Remove the built-in rechargeable battery before disposal of the battery pack. Please make sure that the batteries are disposed of at an officially

assigned location, it should not be mixed with general household waste.

• Before disposal of the battery pack, make sure there is not power left inside batteries. Then open the battery pack and the take out the batteries.

Correct Disposal of This Product

This marking indicates that this product should not be disposed with other household wastes. To prevent possible harm to the

env

ironment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material

resources. To return your used device, please use the return and collection systems or contact the retailer where the product was

purchased. They can take this product for environmentally safe recycling.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

BM-2SL 20L Wet & Dry Vacuum

E&OE © Baumr-AG 5

Safety Symbols

The product may have safety warning labels attached to it, explained below. Understand the symbols on your

product and their meanings. If any stickers become unreadable, unattached etc., replace them.

Flammable Material Hazard

Flammable liquids, gases, or

substances etc may present.

Avoid ignition sources and open

flames. Danger of fire.

Read User Manual

Read and fully understand

product safety warnings,

operation, procedures etc before

using the product.

Use Hand Protection

Wear appropriate hand protection

and take due care as the product

or use of the product may present

hand hazards.

Carbon-Monoxide Hazard

Do not use the product in

confined areas or without

adequate ventilation. Carbon-

monoxide poisoning can be fatal.

Electrocution / Electrical Shock

Hazard

High voltage or high current

electricity may be present or

required by the product. Take

due care when handling electrical

products, cables, plugs and

leads. Electrical shock can be

fatal.

Toxic Fumes / Dust Hazard

Using the product or by-products

from use may produce fumes,

smoke or particles that could be

harmful if inhaled. Wear

appropriate breathing protection

and have adequate ventilation.

Explosive Material Hazard

Combustible liquids, gases, or

substances etc may be present.

Avoid ignition sources and open

flames. Danger of explosion.

Cutting / Amputation Hazard

The product may have blades,

edges or mechanical devices that

can cause severe cut injury to

fingers, limbs etc. Take due care

when handling and using the

product.

Crush Hazard

The product may have blades,

edges or mechanical devices that

can cause severe crush injury to

fingers, limbs etc. Take due care

when handling and using the

product.

Single Operator Only

The product must be operated by

a single person only. More than

one person operating the product

may introduce additional hazards.

Use Face Protection

Wear appropriate full-face

protection and take due care as

the product or use of the product

may present face and eye

hazards.

Use Foot Protection

Wear appropriate foot protection

and take due care as the product

or use of the product may present

foot hazards.

Use Eye / Ear / Head Protection

Wear appropriate eye and / or

ear and / or head protection and

take due care as the product or

use of the product may present

eye, hearing, and head hazards.

Running Hazard

Do not run on or near the product

as doing so may present a fall

hazard.

Diving Hazard

Do not dive into the product as

doing so may present a neck /

head injury hazard.

Adult Supervision Required

Always supervise children and

other users of a product to

prevent drowning or injury.

Skin Penetration / Puncture

Hazard

The product may produce

pressure, emit liquids or objects

that can cause severe injury to

fingers, limbs, blood etc. Take

due care when handling and

using the product.

Hot Surface Hazard

Be aware that the product may

produce high temperatures and

hot surfaces that can cause burn

injuries.

Flying Debris Hazard

Be aware that the product or use

of the product may present

hazards produced by flying

debris. Wear appropriate clothing

and protective devices.

Moving Parts Hazard

Be aware that the product

contains or uses mechanical

devices that move or rotate.

Always wait for moving parts to

stop fully before handling the

product, adjusting, maintenance

etc.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

BM-2SL 20L Wet & Dry Vacuum

E&OE © Baumr-AG 6

Carbon-Monoxide Hazard

Do not use the product in

confined areas or without

adequate ventilation. Carbon-

monoxide poisoning can be fatal.

Pull Hazard

Be aware that the product

contains or uses mechanical

devices that can pull in objects

and can cause severe injury to

fingers, limbs etc. Take due care

when handling and using the

product.

Slope / Fall Injury Hazard

Be aware that using the product

on sloping surfaces or in slippery

conditions may present additional

dangers from falls and contact

with blades, moving parts, hot

surfaces etc.

"Slam Dunk" Warning

Do NOT attempt "slam dunk"

manoeuvres as this may result in

severe injury due to falling,

product breakage or collapse etc.

Electrocution / Electrical Shock

Hazard - Outdoor

High voltage or high current

electricity may be present or

required by the product. Do NOT

use in rain, damp, or wet

conditions. Electrical shock can

be fatal.

Electrocution / Electrical Shock

Hazard - Disconnect

High voltage or high current

electricity may be present or

required by the product. Always

disconnect the product from the

electrical supply before handling

the product, adjusting,

maintenance etc.

Power Line Electrocution

Hazard

High voltage / high current power

lines may be present. Use

extreme caution to avoid contact

or interference with power lines.

Electrical shock can be fatal.

"Kick-Back" Hazard

High level of "kick-back" hazard

that can cause the machine to

suddenly rotate towards operator.

Kick-back injury can be fatal.

Winch Operator Position

Hazard

Do NOT stand between winch

and load. Do NOT use winch to

move people.

Winch Lift Hazard

Do NOT LIFT load vertically. Use

machine to PULL only.

Cable Hazard

Ensure that load bearing cable is

not kinked or knotted.

Winch Cable Hazard

Ensure that there is a minimum

number of cable coils on

winching mechanism.

Winch Hook Hazard

Carry hook to load – do NOT

throw or run.

Flash / Blinding Hazard

Wear appropriate eye protection

for welding. Direct exposure to

weld arcs may cause permanent

eye injury.

Laser Hazard

Laser may be in use – do NOT

look directly at laser or allow

others to.

Choking Hazard

Children under 8 yrs. Can choke

or suffocate on small parts. Adult

supervision required.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

BM-2SL 20L Wet & Dry Vacuum

E&OE © Baumr-AG 7

Table of Contents

Safety ............................................................................................................................................................. 2

Safety Symbols ........................................................................................................................................................... 5

Parts Identification ....................................................................................................................................... 8

Assembly ....................................................................................................................................................... 9

Operation ..................................................................................................................................................... 10

Charging the Battery ................................................................................................................................................. 10

ON/OFF Switch ......................................................................................................................................................... 11

General Vacuum Operation ...................................................................................................................................... 11

Emptying the Dust Tank ........................................................................................................................................... 12

Wet Vacuuming ........................................................................................................................................................ 13

Blower Operation ...................................................................................................................................................... 14

Accessories Operation ............................................................................................................................................. 14

Lithium Battery Care and Maintenance .................................................................................................... 15

Top 3 Battery Care Requirements ............................................................................................................................ 15

Maintenance ................................................................................................................................................ 17

General Maintenance ............................................................................................................................................... 17

Filter Cleaning ........................................................................................................................................................... 17

Troubleshooting ......................................................................................................................................... 18

Specifications ............................................................................................................................................. 18

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

BM-2SL 20L Wet & Dry Vacuum

E&OE © Baumr-AG 8

Parts Identification

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

BM-2SL 20L Wet & Dry Vacuum

E&OE © Baumr-AG 9

Assembly

1. Loosen Clips (Fig. 1).

2. Raise the nose assembly from the dustpan (Fig. 2).

3. Take out all accessories from the dust container (Fig. 3).

4. Install the wheels. Align the corresponding holes, push down, and install the four casters on the barrel (Fig.

4).

5. Place the nose assembly on the dust barrel that already has a filter assembly and lock it with both sides of

the clips (Fig. 5).

6. Open the battery cover. Do this by swinging up the cover, as shown. Then insert the battery into the mount

and push it down until you hear the battery engage (Fig. 6).

7. Cover the battery cover (Fig. 7).

8. Align the hose assembly port with the suction port, and then rotate it to the right and insert it (Fig. 8).

9. Optional tube and hose assemblies can be installed. It will be a diameter of the big end of the force in place

(Fig. 9).

10. Optional brush and three tube installation. Will be one end of the brush to plug in place (Fig. 10).

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

BM-2SL 20L Wet & Dry Vacuum

E&OE © Baumr-AG 10

Operation

Charging the Battery

1. Remove the Battery Pack (Fig 1): Take the battery pack out of the equipment by pressing the side push-lock

buttons.

2. Charging the Battery (Fig 2):

a. Check that your mains voltage matches the voltage marked on the rating plate of the battery charger.

b. Insert the power plug of the charger into the socket outlet.

c. Insert the battery charger into the battery pack.

d. The indicator light on the charger will show red, indicating that the charger is starting to charge.

e. The indicator light will turn green when the battery is fully charged.

NOTE: The charger indicator may show green if the battery is charged immediately after a long

period of operation. After a few minutes, it will show red to start charging. This is a normal

phenomenon to avoid the danger of high-temperature charging.

3. Check Battery Capacity:

Press the switch for the battery capacity indicator. The battery capacity indicator shows the charge status of

the battery using 4 LEDs:

− All 4 LEDs lit: The battery is fully charged.

− 3 or 2 LEDs lit: The battery has an adequate remaining charge.

− 1 LED lit: The battery is empty and needs recharging.

WARNING: Batteries must be charged normally within the ambient temperature range of 0°C-45°C.

Charging should be prohibited when the ambient temperature is below 0°C.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

BM-2SL 20L Wet & Dry Vacuum

E&OE © Baumr-AG 11

ON/OFF Switch

General Vacuum Operation

1. Loosen the Clips (Fig. 1).

2. Raise the Head assembly from the dust tank (Fig. 2).

3. Install the HEPA, secure the HEPA tightly on the bottom cap basket (Fig. 3).

4. Place the nose assembly on the dust bucket and lock it with both sides of the buckle (Fig. 4).

5. Open the battery cover. Do this by swinging up the cover, as shown. Then insert the battery into the mount

and push it down until you hear the battery engage (Fig. 5).

6. Cover the battery cover (Fig. 6).

7. Align the hose assembly port with the suction port, and then rotate it to the right and insert it (Fig. 7).

Press to

start vacuum

Press to stop

vacuum

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

BM-2SL 20L Wet & Dry Vacuum

E&OE © Baumr-AG 12

8. Optional three tube and hose assemblies can be installed. It will be a three-tube diameter of the big end of

the force in place (Fig. 8).

9. When choosing the three-tube installation, it will be a three-tube diameter of the big end of the force in place

(Fig. 9).

10. Optional brush and three tube installation. It will be one end of the brush to plug in place (Fig. 10).

11. Start the switch button (Fig. 11).

12. Start the vacuum (Fig. 12).

WARNING: BE SURE TO READ, UNDERSTAND, AND APPLY INFORMATION, ENTITLED ‘SAFETY

INSTRUCTIONS & WARNINGS’. DO NOT VACUUM IN AREAS WITH FLAMMABLE GASES, VAPORS, OR

EXPLOSIVE DUSTS IN THE AIR. FLAMMABLE GASES OR VAPORS INCLUDE BUT ARE NOT LIMITED

TO; LIGHTER FLUID, SOLVENT TYPE CLEANERS, OIL-BASE PAINTS, GASOLINE, ALCOHOL OR

AEROSOL SPRAYS. EXPLOSIVE DUSTS INCLUDE BUT ARE NOT LIMITED TO, COAL, MAGNESIUM,

GRAIN OR GUN POWDER. TO REDUCE THE RISK OF HEALTH HAZARDS FROM VAPORS OR DUST, DO

NOT VACUUM TOXIC MATERIALS.

Emptying the Dust Tank

1. Check if the dust tank is full (Fig. 1).

2. Turn off the vacuum (Fig. 2).

3. Release the buckle (Fig. 3).

4. Raise the nose assembly from the dust container (Fig. 4).

5. Properly dispose of the contents from the dust bucket (Fig. 5).

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

BM-2SL 20L Wet & Dry Vacuum

E&OE © Baumr-AG 13

Wet Vacuuming

1. Cover the bottom cap basket with a water-absorbing sponge, make sure to cover the whole basket (Fig. 1).

2. Place the Head assembly on the dust barrel and lock it with both sides of the clips (Fig. 2).

3. Turn vacuum ON (Fig. 3).

4. Install the required suction accessories on the hose assembly (Fig. 4).

5. When the water is absorbed to the maximum capacity, the safety valve operates, and the suction port has no

more suction, turn OFF the power (Fig. 5).

6. Pour out the water (Fig. 6).

7. To ensure the best water absorption results, please remove the air filter sponge and gently hand-wring it dry

after drainage (Fig. 7).

8. Wash the sponge with clean running water, and gently hand-wring it dry before re-using it again (Fig. 8).

WARNING: BE SURE TO READ, UNDERSTAND, AND APPLY INFORMATION, ENTITLED ‘SAFETY

INSTRUCTIONS & WARNINGS’. DO NOT VACUUM IN AREAS WITH FLAMMABLE GASES, VAPORS, OR

EXPLOSIVE DUSTS IN THE AIR. FLAMMABLE GASES OR VAPORS INCLUDE BUT ARE NOT LIMITED

TO; LIGHTER FLUID, SOLVENT TYPE CLEANERS, OIL-BASE PAINTS, GASOLINE, ALCOHOL OR

AEROSOL SPRAYS. EXPLOSIVE DUSTS INCLUDE BUT ARE NOT LIMITED TO, COAL, MAGNESIUM,

GRAIN, OR GUN POWDER. TO REDUCE THE RISK OF HEALTH HAZARDS FROM VAPORS OR DUST, DO

NOT VACUUM TOXIC MATERIALS.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

BM-2SL 20L Wet & Dry Vacuum

Blower Operation

WARNING: ALWAYS WEAR SAFETY GOGGLES BEFORE USING BLOWER. KEEP BY STANDERS CLEAR

FROM BLOWING DEBRIS. WEAR A DUST MASK IF BLOWING CREATES DUST THAT MIGHT BE

INHALED.

1. Unscrew the inserted hose assembly from the suction port with a left-hand rotation (Fig. 1).

2. Insert the main cannula of the hose assembly into the air outlet at the back of the head and tighten it with the

right-hand rotation (Fig. 2).

3. Start the switch button (Fig. 3).

4. Hold the hose assembly and aim the outlet port towards leaves/debris (Fig. 4).

Accessories Operation

1. Storage brush, crevice nozzle.

2. Storage brush, crevice nozzle, floor nozzle, tubes.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

BM-2SL 20L Wet & Dry Vacuum

Lithium Battery Care and Maintenance

Top 3 Battery Care Requirements

1. Charge battery before first use. The battery may arrive with some charge, regardless of this the

battery must be charged on the initial charge and for each subsequent charge.

2. Charge battery immediately when it is depleted. Do not store a depleted battery. This will

permanently impact the life of the battery. If the battery is going to be stored for a period of time, fully

charge the battery before storing.

3. Disconnect battery when not in use. To prolong the life of a battery, disconnect it from the unit

when not in use. Disconnect chargers from the battery once charged.

To ensure the battery maintains optimum performance, follow the guidelines outlined below.

•

For best results, charge batteries in temperatures between 10°C and 30°C

•

When battery is charged, disconnect the charger from the power supply and remove the battery from the

charger.

•

If a battery is stored or otherwise unused for an extended period, and the battery has no charge remaining

when you check it, consider it to be damaged. Do not attempt to recharge it or to use it. Replace it with a

new battery.

•

Use only with the battery charger specified by the manufacturer.

•

Ensure that the battery charger electrical cord is not subjected to damage or stress. Do not operate the

battery charger if it has a damaged electrical cord or plug.

•

Do not use the charger in wet areas or expose it to rain or water.

•

The typical estimated life of a Lithium-Ion battery is about two to three years or 300 to 500 charge cycles,

whichever occurs first. One charge cycle is a period of use from fully charged, to fully discharged, and fully

recharged again.

•

Explosion hazard – protect the battery against heat, for example, direct sunlight and fire. Do not store

batteries in vehicles or locations subject to heat.

•

Batteries can explode in the presence of an ignition source, such as a pilot light. To reduce the risk of

serious personal injury, never use any cordless product in the presence of open ﬂame. Exploding batteries

can propel debris and chemicals.

•

Do not open the battery – danger of short-circuiting and/or explosion.

•

Do not attempt to destroy or disassemble the battery pack or remove any of its components.

•

Do not touch the battery terminals with metal objects and/or body parts as short-circuit and/or personal injury

may result.

•

Explosion hazard – do not open and/or short-circuit the battery.

•

Poison hazard – battery leakage (liquid ejection). Under extreme conditions, liquid may be ejected from the

battery – avoid contact. If contact accidentally occurs, immediately seek medical attention, and flush with

water. If liquid contacts eyes, immediately seek medical attention, flush with clean water for at least 10

minutes. Liquid ejected from the battery may cause irritation or burns.

•

Dispose of non-serviceable batteries in an environmentally responsible manner and according to local

regulations.

Failure to adhere to the requirements above may result in the battery becoming inoperative or battery life being

reduced. In extreme cases or abuse, battery overheating, or fire may result.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

BM-2SL 20L Wet & Dry Vacuum

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

BM-2SL 20L Wet & Dry Vacuum

Maintenance

WARNING! TO REDUCE THE RISK OF ELECTRIC SHOCK, UNPLUG BEFORE PERFORMING ANY

MAINTENANCE.

General Maintenance

•

After cleaning the barrels, filters, and related accessories, check if there are leaks. After each use, clean the

filter; NEVER use a wet filter.

•

Check if the air intake is clogged and clean it in a timely manner.

•

Carefully store the machine, do not beat it.

•

Keep the machine dry.

•

If the filter is covered with dust, wash it with cold water, and if necessary, may also use neutral detergent to

clean. Do not use corrosive cleaners to clean. Do not put entire head directly in the water cleaning.

•

After an extended period, the filter will be covered with dust, and suction power will be weakened. To avoid

this, always clean the filter in a timely manner.

•

If you observe any abnormal vibration, noise, or smell, immediately stop using the machine, and

inspect/perform the necessary maintenance.

Filter Cleaning

•

Periodically check the cleaning filter to maintain performance.

•

If the suction has very tiny dust, the filter may need more frequent cleaning.

•

Wash filter sponge with cold or warm water without the use of detergent (Fig. 1 and 2).

•

Keep the cleaned parts in an open, well-ventilated area to air-dry for at least 24 hours.

•

Do not put the filter in a dishwasher, washing machine, roller dryer, oven, microwave oven or open flame

(Fig. 3).

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

BM-2SL 20L Wet & Dry Vacuum

Troubleshooting

WARNING! TO REDUCE THE RISK OF ELECTRIC SHOCK, UNPLUG BEFORE PERFORMING ANY

TROUBLESHOOTING.

Symptom Possible Causes Corrective Action

Vacuum will not operate

No battery pack installed Install Battery Pack

Battery packs run out of power

Charge the battery pack with a charger, then

use it.

Container full. Empty container.

Dust comes out from

motor cover.

The cartridge filter or collection bag is

missing or damaged.

Attach or replace cartridge filter or collection

bag.

Reduced efficiency and

motor/speed vibration.

There is a blockage in the nozzle or

hose, or the container inlet. Or dust filter

blocked by fine dust.

Check nozzle, hose, and container inlets for

blockage. Take off the filter and clean it. Or

install new cartridge filter.

Specifications

Function Wet and dry vacuuming / Blowing

Voltage 18.5V

Tank Capacity 20L

Airflow Volume 16L/s

Power 200W

Hose Length 1.5m

Hose Diameter 32mm

Tank Material Stainless Steel

Tank Diameter 280mm

Suction 15Kpa

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Some experts believe that the incorrect or prolonged use of almost any

product may cause serious injury or death. To help reduce your risk of

serious injury or death, refer to the information below. For more information,

see www.datastreamserver.com/safety



Consult all documentation, packaging,

and product labelling before use. Note

that some products feature

documentation available online. It is

recommended to print and retain the

documentation.



Before each use, check the product for

loose/broken/damaged/missing parts,

wear, or leaks (if applicable). Never use a

product with

loose/broken/damaged/missing parts,

wear, or leaks.



Products must be inspected and serviced

(if applicable) by a qualified technician

every 6 months. This is based on

average residential use by persons of

average size and strength, and on a

property of average metropolitan size.

Use beyond these recommendations may

require more frequent

inspections/servicing.



Ensure that all users of the product have

completed a suitable industry recognised

training course before being allowed

access to the product.



The product has been supplied by a general merchandise

retailer that may not be familiar with your specific

application or description of application. Be sure to attain

third-party approval from a qualified specialist for your

application before use, regardless of any assurances from

the retailer or its representatives.



This product is not intended for use where fail-safe

operation is required. As with any product (for example,

automobile, computer, toaster), there is the possibility of

technical issues that may require the repair or

replacement of parts, or the product itself. If the possibility

of such failure and the associated time it may take to

rectify could in any way inconvenience the user, business,

or employee, or financially affect the user, business, or

employee, then the product is not suitable for your

requirements. This product is not intended for use where

incorrect operation or a failure of any kind, including but

not limited to, a condition requiring product return,

replacement, parts replacement, or service by a

technician may cause financial loss, loss of employee

time or an inconvenience requiring compensation.



If this product has been purchased in error when

considering the information presented here, contact the

retailer directly for details of their returns policy, if

required.

diagrams, or images may be reproduced or transmitted in any form or by any means, electronic or

mechanical, including photocopying, scanning, or recording, or any information storage and retrieval system,

without express permission or consent from the publisher.

BAUMR-AG TOLWDVBM2SLA Cordless Wet & Dry Vacuum Cleaner Kit

Product's Documents

Product manual

Specifications

BAUMR-AG TOLWDVBM2SLA Questions and Answers