Loading ...
Loading ...
Loading ...
5
Depth Adjustment
Start with about 1/16" clearance
1/16"
between the head of the screw
and nose. Every two clicks of the
depth adjusting collar equal 1/64"
in driving depth. Continue adjust-
ing the depth locator to the de-
sired depth.
1. To increase the driving depth,
turn the depth adjusting collar
clockwise .
2. To decrease the driving depth,
turn the depth adjusting collar
counterclockwise .
APPLICATIONS
WARNING
To reduce the risk of electric shock,
check work area for hidden pipes
and wires before drilling or driving screws.
Driving Drywall Screws
Standard drywall screws are generally designed
for attaching drywall to wood studs and 26 through
20-gauge steel studs. The depth setting is very
important. Refer to the guide below for the correct
depth setting.
NOTE: Practice driving screws into
Too deep. Head of
screw punches hole
in drywall surface,
making finishing
dicult and allowing
moisture beneath
facing. Decrease
depth.
Too shallow. Head
of screw extends
above drywall
face and can not
be finished off.
Increase depth.
Correct. Head of
screw is below sur-
face, but does not
puncture facing.
pieces of scrap material to become
familiar with the tool before attempt-
ing to drive screws into the work-
piece.
1. Select the proper drywall screw
for each job. Pilot holes are not
needed.
2. Turn on auto-start (if desired).
3. Move the control switch to forward.
4. Pull the trigger and slide the
lock-on up (if desired). Release
the trigger.
5. Place the screw onto the depth
locator, then align the screw
against the work surface, making
sure to hold the tool and screw
square to the work surface. If the
tool or screw are misaligned, the
screw will not drive into the work
surface or it will not drive straight.
6. Push the tool forward with a
“punching” motion and maintain
pressure to drive the screw. The
tool will turn on, and the bit will
begin to spin. If pressure is not
maintained, the screw will not
properly seat.
7. When the drive depth has been
reached, the tool will turn o and
the bit will stop spinning.
8. To remove screws, remove the
nose cone and move the control
switch to reverse.
MAINTENANCE
WARNING
To reduce the risk of injury, always
unplug the charger and remove the
battery pack from the charger or tool before
performing any maintenance. Never disassemble
the tool, battery pack or charger. Contact a
MILWAUKEE service facility for ALL repairs.
Maintaining Tool
Keep your tool, battery pack and charger in good
repair by adopting a regular maintenance program.
Inspect your tool for issues such as undue noise,
misalignment or binding of moving parts, breakage of
parts, or any other condition that may aect the tool
operation. Return the tool, battery pack, and charger
to a MILWAUKEE service facility for repair. After six
months to one year, depending on use, return the
tool, battery pack and charger to a MILWAUKEE
service facility for inspection.
If the tool does not start or operate at full power with
a fully charged battery pack, clean the contacts on
the battery pack. If the tool still does not work prop-
erly, return the tool, charger and battery pack, to a
MILWAUKEE service facility for repairs.
WARNING
To reduce the risk of personal in-
jury and damage, never immerse
your tool, battery pack or charger in liquid or
allow a liquid to ow inside them.
Cleaning
Clean dust and debris from vents. Keep handles
clean, dry and free of oil or grease. Use only mild
soap and a damp cloth to clean, since certain clean-
ing agents and solvents are harmful to plastics and
other insulated parts. Some of these include gasoline,
turpentine, lacquer thinner, paint thinner, chlorinated
cleaning solvents, ammonia and household deter-
gents containing ammonia. Never use ammable or
combustible solvents around tools.
Repairs
For repairs, return the tool, battery pack and charger
to the nearest authorized service center.
ACCESSORIES
WARNING
Use only recommended accesso-
ries. Others may be hazardous.
For a complete listing of accessories, go online to
www.milwaukeetool.com or contact a distributor.
SERVICE - UNITED STATES
1-800-SAWDUST (1.800.729.3878)
Monday-Friday, 7:00 AM - 6:30 PM CST
or visit www.milwaukeetool.com
Contact Corporate After Sales Service Technical
Support with technical, service/repair, or warranty
questions.
Email: [email protected]
Become a Heavy Duty Club Member at
www.milwaukeetool.com to receive important
notications regarding your tool purchases.
SERVICE - CANADA
Milwaukee Tool (Canada) Ltd
1.800.268.4015
Monday-Friday, 7:00 AM - 4:30 PM CST
or visit www.milwaukeetool.ca
Loading ...
Loading ...
Loading ...