Loading ...
Projects LN-704
Architectural Coatings Liquid Nails Projects Interior Construction Adhesive
PRECAUTIONS
PPG Architectural Finishes, Inc. believes the technical data presented is currently accurate: however, no guarantee of accuracy, comprehensiveness, or performance is given or implied.
Improvements in coatings technology may cause future technical data to vary from what is in this bulletin. For complete, up-to-date technical information, call 1-800-441-9695.
PPG Architectural Finishes, Inc.
One PPG Place
Pittsburgh, PA 15272
www.liquidnails.com
Technical Services
1-800-441-9695
PPG Architectural Coatings Canada Inc.
1550 rue Ampère, Suite 500
Boucherville (Quebec) J4B 7L4
Architect/Specifier
1-888-PPG-IDEA
WARNING! HARMFUL IF INHALED. Sanding and grinding dusts may be harmful if inhaled. This product contains crystalline silica which can cause lung
cancer or silicosis. The risk of cancer depends on the duration and level of exposure to dust from sanding surfaces. Do not breathe vapor. Do not swallow. Do not
get on skin or clothing. Keep container tightly closed and sealed until ready for use. Wash thoroughly after handling. Provide fresh air ventilation during and after
application and drying. Avoid the inhalation of dust or particulates arising from the application of this preparation. Use personal protective equipment as required.
FIRST AID: If swallowed, rinse mouth with water (only if the person is conscious). Do not induce vomiting unless directed to do so by medical personnel. If in eyes,
rinse with water for 15 minutes. Check for and remove any contact lenses. If on skin, rinse well with water. Wash with soap and water. Get medical attention if irri-
tation develops. If inhaled, remove to fresh air. Call physician immediately. Contains isothiazolinones. May cause allergic reaction. Keep out of the reach of children.
For workplace use, an SDS is available from your retailer or by calling (412) 492-5555. EMERGENCY SPILL INFORMATION: (412) 434-4515 (U.S.). WARNING:
Cancer – www.P65Warnings.ca.gov.
LN-704 8/2022
© 2022 PPG Industries, Inc. All Rights Reserved. The PPG Logo is a registered trademark of PPG Industries Ohio, Inc. Liquid Nails is a registered trademark of PPG Architectural
Finishes, Inc. UL Greenguard is a certification mark of UL LLC.
WARNING! If you scrape, sand, or remove old paint, you may release lead dust or fumes. LEAD IS TOXIC. EXPOSURE TO LEAD DUST OR
FUMES CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO
AVOID EXPOSURE. Wear a properly fitted, NIOSH-approved respirator and prevent skin contact to control lead exposure. Clean up carefully with
a HEPA vacuum and a wet mop. Before you start, find out how to protect yourself and your family by contacting the USEPA National Lead
Information Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead. Follow these instructions to control exposure to other hazardous sub-
stances that may be released during surface preparation.
DIRECTIONS: Surfaces must be clean, structurally sound, and free of loose particles. For smooth surfaces, adhesion can be improved by lightly
sanding bond area. Cut cartridge tip to desired bead size, puncture foil seal inside the tip of the cartridge, and place cartridge into caulk gun. Apply
when 40°F (4°C) and higher. One surface must be porous. Furring Strips or Studs: Apply ¼" (6 mm) zigzag bead to each strip or stud. Press
into place. Use nails at both ends. For Foamboard, Paneling, Corkboard, Brick Veneer, etc., to Flat Surfaces: Use ¼" (6 mm) vertical zigzag
beads a maximum of 12" (30.5 cm) apart and within ½" (13 mm) of all edges.
CLEANUP: Water for wet adhesive; scraping and mineral spirits when dry.
DISPOSAL: Contact your local environmental regulatory agency for guidance on disposal of unused product.
PERMISSIBLE TEMPERATURES DURING APPLICATION:
Material: 40 to 100ºF 4 to 38ºC
Ambient: 40 to 100ºF 4 to 38ºC
Substrate: 40 to 100ºF 4 to 38ºC
GENERAL SURFACE PREPARATION/APPLICATION