BAUMR-AG TOLCLSBMRAMT3 Cordless MT3 20V SYNC 3in1 User Manual

THE BATTERY MAY HAVE SOME CHARGE ON ARRIVAL, IT IS IMPORTANT

HOWEVER THAT THE BATTERY IS CHARGED PRIOR TO USE.

User Manual

[Revision 4.0 October 2023]

READ THIS MANUAL CAREFULLY BEFORE USE – FAILURE TO DO SO MAY RESULT IN INJURY, PROPERTY DAMAGE AND MAY

VOID WARRANTY. • KEEP THIS MANUAL FOR FUTURE REFERENCE. • Products covered by this manual may vary in appearance,

assembly, inclusions, specifications, description, and packaging.

MT3 Multi-Tool Kit

Safety

Safety messages are designed to alert you to possible dangers or hazards that could cause death, injury or

equipment or property damage if not understood or followed. Safety messages have the following symbols:

You WILL be KILLED or

SERIOUSLY INJURED if you do

not follow instructions.

You CAN be KILLED or

SERIOUSLY INJURED if you do

not follow instructions.

You CAN be INJURED if you do

not follow instructions or equipment

damage may occur.

It is vital that you read and understand this

user manual before using the product,

including safety warnings, and any assembly

and operating instructions. Keep the manual

for future reference.

Safety precautions and recommendations

detailed here must be fully understood and

followed to reduce the risk of injury, fire,

explosion, electrical hazard, and/or property

damage.

Safety information presented here is generic

in nature – some advice may not be

applicable to every product. The term

"equipment" refers to the product, be it

electrical mains powered, battery powered or

combustion engine powered.

• Before Use - If you are not familiar with the

safe operation/handling of the equipment or

are in any way unsure of any aspect of

suitability or correct use for your

application, you should complete training

conducted by a person or organization

qualified in safe use and operation of this

equipment, including fuel/electrical handling

and safety.

• Do NOT operate the equipment in

flammable or explosive environments, such

as in the presence of flammable liquids,

gases, or dust. The equipment may create

sparks or heat that may ignite flammable

substances.

• Keep clear of moving parts.

• Equipment may be a potential source of

electric shock or injury if misused.

• Do NOT operate the equipment if it is

damaged, malfunctioning or is in an

excessively worn state.

• Do NOT allow others to use the equipment

unless they have read this manual and are

adequately trained.

• Keep packaging away from children - risk

of suffocation! Operators must use the

equipment correctly. When using the

equipment, consider conditions and pay

due care to persons and property.

General Work Area Safety

• Work areas should be clean and well it.

• Do not operate the equipment if

bystanders, animals etc are within

operating range of the equipment or the

general work area.

• If devices are provided for connecting dust

extraction / collection facilities, ensure

these are connected and used properly.

Dust collection can reduce dust-related

hazards.

General Personal Safety

• Wear appropriate protective equipment

when operating, servicing, or when in the

operating area of the equipment to help

protect from eye and ear injury, poisoning,

burns, cutting and crush injuries. Protective

equipment such as safety goggles,

respirators, non-slip safety footwear, hard

hat, hearing protection etc should be used

for appropriate equipment / conditions.

Other people nearby should also wear

appropriate personal protective equipment.

Do not wear loose clothing or jewellery,

which can be caught in moving parts. Keep

hair and clothing away from the equipment.

• Stay alert and use common sense when

operating the equipment. Do not over-

reach. Always maintain secure footing and

balance.

• Do not use the equipment if tired or under

the influence of drugs, alcohol, or

medication.

• This equipment is not intended for use by

persons with reduced physical, sensory, or

mental capabilities.

General Fuel Safety

• Petrol/fuel/gasoline is extremely flammable

– keep clear of naked flames or other

ignition sources.

• Do not spill fuel. If you spill fuel, wipe it off

the equipment immediately – if fuel gets on

your clothing, change clothing.

• Do NOT smoke near fuel or when

refuelling.

• Always shut off the engine before

refuelling.

• Do NOT refuel a hot engine.

• Open the fuel cap carefully to allow any

pressure build-up in the tank to release

slowly.

• Always refuel in well ventilated areas.

• Always check for fuel leakage. If fuel

leakage is found, do not start, or run the

engine until all leaks are fixed.

General Carbon-Monoxide Safety

• Using a combustion engine indoors CAN

KILL IN MINUTES. Engine exhaust

contains carbon-monoxide – a poison you

cannot smell or see.

• Use combustion engines OUTSIDE only,

and far away from windows, doors, and

vents.

General Equipment Use and Care

• The equipment is designed for domestic

use only.

• Handle the equipment safely and carefully.

• Before use, inspect the equipment for

misalignment or binding of moving parts,

loose components, damage, or any other

condition that may affect its operation. If

damaged, have the equipment repaired by

an authorised service centre or technician

before use.

• Prevent unintentional starting of the

equipment - ensure equipment and power

switches are in the OFF position before

connecting or moving equipment. Do not

carry equipment with hands or fingers

touching any controls. Remove any tools or

other items that are not a part of the

equipment from it before starting or

switching on.

• Do not force the equipment. Use the

correct equipment for your application.

Equipment will perform better and be safer

when used within its design and usage

parameters.

• Use the equipment and accessories etc. in

accordance with these instructions,

considering working conditions and the

work to be performed. Using the equipment

for operations different from those intended

could result in hazardous situations.

• Always keep equipment components

(engines, hoses, handles, controls, frames,

housings, guards etc) and accessories

(cutting tools, nozzles, bits etc) properly

maintained. Keep the equipment clean and,

where applicable, properly lubricated.

• Store the equipment out of reach of

children or untrained persons. To avoid

burns or fire hazards, let the equipment

cool completely before transporting or

storing. Never place or store the equipment

near flammable materials, combustible

gases, or liquids etc.

• The equipment is not weather-proof, and

should not be stored in direct sunlight, at

high ambient temperatures or locations that

are damp or humid.

• Do not clean equipment with solvents,

flammable liquids, or harsh abrasives.

• For specific equipment safety use and care,

see Equipment Safety.

MT3 Multi-Tool Kit

General Electrical Safety

• Inspect electrical equipment, extension

cords, power bars, and electrical fittings for

damage or wear before each use. Repair or

replace damaged equipment immediately.

• Ensure all power sources conform to

equipment voltage requirements and are

disconnected before connecting or

disconnecting equipment.

• When wiring electrically powered

equipment, follow all electrical and safety

codes.

• Wherever possible, use a residual current

device (RCD).

• High voltage / high current power lines may

be present. Use extreme caution to avoid

contact or interference with power lines.

Electrical shock can be fatal.

General Electrical Safety

• Electrically grounded equipment must have

an approved cord and plug and be

connected to a grounded electrical outlet.

• Do NOT bypass the ON/OFF switch and

operate equipment by connecting and

disconnecting the electrical cord.

• Do NOT use equipment that has exposed

wiring, damaged switches, covers or

guards.

• Do NOT use electrical equipment in wet

conditions or in damp locations.

• Do NOT use electrical cords to lift, move or

carry equipment.

• Do NOT coil or knot electrical cords, and

ensure electrical cords are not trip hazards.

General Service Information

• The equipment must be serviced or

repaired at authorised service centres by

qualified personnel only.

• Replacement parts must be original

equipment manufacturer (OEM) to ensure

equipment safety is maintained.

• Do NOT attempt any maintenance or repair

work not described in this manual.

• After use, the equipment and components

may still be hot – allow the equipment to

cool and disconnect spark plugs and/or

electrical power sources and/or batteries

from it before adjusting, changing

accessories, or performing repair or

maintenance.

• Do NOT adjust while the equipment is

running.

• Perform service-related activities in suitable

conditions, such as a workshop.

• Replace worn, damaged or missing

warning/safety labels immediately.

Application

This cordless tool is intended for:

• Screwing screws in and out and for drilling holes in wood, metal, or plastic.

• Sawing wood, metal, and plastics

• The tool is not suitable for commercial use. Any other use that is not explicitly approved in these instructions may result in damage to the

equipment and represent a danger to the user.

• The tool is designed for use by adults. Adolescents over the age of 16 may use the device only under supervision. The manufacturer is not liable

for damages caused by unspecified use or incorrect operation.

• WARNING! FOR YOUR OWN SAFETY, READ THIS MANUAL AND THE GENERAL SAFETY INSTRUCTIONS CAREFULLY BEFORE

USING THE APPLIANCE. YOUR POWER TOOL SHOULD ONLY BE GIVEN TO OTHER USERS TOGETHER WITH THESE INSTRUCTIONS.

General Power Tool Safety Warnings

• WARNING! READ ALL SAFETY WARNINGS, INSTRUCTIONS, ILLUSTRATIONS AND SPECIFICATIONS PROVIDED WITH THIS POWER

TOOL. FAILURE TO FOLLOW ALL INSTRUCTIONS LISTED BELOW MAY RESULT IN ELECTRIC SHOCK, FIRE AND/OR SERIOUS

INJURY.

• Save all warnings and instructions for future reference. The term "power tool" in the warnings refers to your mains-operated (corded) power tool

or battery-operated (cordless) power tool.

Work Area Safety

• Keep work area clean and well lit. Cluttered or dark areas invite accidents.

• Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks

which may ignite the dust or fumes.

• Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

Electrical Safety

• Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools.

Unmodified plugs and matching outlets will reduce risk of electric shock.

• Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric

shock if your body is earthed or grounded.

• Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.

• Do not abuse the cord. Never use the cord for carrying, pulling, or unplugging the power tool. Keep cord away from heat, oil, sharp edges or

moving parts. Damaged or entangled cords increase the risk of electric shock.

• When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of

electric shock.

• If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the

risk of electric shock.

Personal Safety

• Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under

the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.

• Use personal protective equipment. Always wear eye protection. Protective equipment such as a dust mask, non-skid safety shoes, hard hat or

hearing protection used for appropriate conditions will reduce personal injuries.

MT3 Multi-Tool Kit

• Prevent unintentional starting. Ensure the switch is in the OFF position before connecting to power source and/or battery pack, picking up or

carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents.

• Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may

result in personal injury.

• Do not overreach. Always keep proper footing and balance. This enables better control of the power tool in unexpected situations.

• Dress properly. Do not wear loose clothing or jewellery. Keep your hair and clothing away from moving parts. Loose clothes, jewellery or long hair

can be caught in moving parts.

• If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust

collection can reduce dust-related hazards.

• Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles. A careless action can

cause severe injury within a fraction of a second.

Power Tool Use and Care

• Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for

which it was designed.

• Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must

be repaired.

• Disconnect the plug from the power source and/or remove the battery pack, if detachable, from the power tool before making any adjustments,

changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.

• Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the

power tool. Power tools are dangerous in the hands of untrained users.

• Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may

affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power

tools.

• Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.

• Use the power tool, accessories, and tool bits etc. in accordance with these instructions, considering the working conditions and the work to be

performed. Use of the power tool for operations different from that intended could result in a hazardous situation.

• Keep handles and grasping surfaces dry, clean, and free from oil and grease. Slippery handles and grasping surfaces do not allow for safe

handling and control of the tool in unexpected situations.

Battery Tool Use and Care

• Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire

when used with another battery pack.

• Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.

• When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws, or other small metal objects,

that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.

• Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts

eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.

• Do not use a battery pack or tool that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behaviour resulting in

fire, explosion, or risk of injury.

• Do not expose a battery pack or tool to fire or excessive temperature. Exposure to fire or temperature above 130 °C may cause explosion.

• Follow all charging instructions and do not charge the battery pack or tool outside the temperature range specified in the instructions. Charging

improperly or at temperatures outside the specified range may damage the battery and increase the risk of fire.

Service

• Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power

tool is maintained.

• Never service damaged battery packs. Service of battery packs should only be performed by the manufacturer or authorized service providers.

Battery Safety

• Never attempt to open for any reason.

• Do not store in locations where the temperature may exceed 40°C (104°F).

• Charge only at ambient temperatures between 4°C and 40°C (39.2°F and 104°F).

• Charge only using the charger provided with the tool.

• Store your batteries in a cool dry place (5°C-20°C/41°F-68°F). Never store batteries in discharged state.

• It is better for Li-ion batteries to discharge and reload them regularly (at least 4 times a year). The ideal charge for long-term storage of your Li-

ion battery is 40% of capacity.

• When disposing of batteries, follow your local laws.

• Do not cause short circuits. If connection is made between the positive (+) and negative (-) terminal directly or via accidental contact with metallic

objects, the battery is short circuited, and an intense current will flow causing heat generation which may lead to casing rupture or fire.

• Do not expose to heat sources. If batteries are heated to above 100°C (212°F), sealing and insulating separators and other polymer components

may be damaged resulting in electrolyte leakage and/or internal short circuiting leading to heat generation causing rupture or file. Moreover, do

not throw the batteries in fire, explosion and/or intense burning may result.

• Under extreme conditions, battery leakage may occur. When you notice liquid on the battery, proceed as follows:

• Carefully wipe the liquid off using a cloth. Avoid skin contact.

MT3 Multi-Tool Kit

• In case of skin or eye contact, follow the instructions below:

• Immediately rinse with water. Neutralize with a mild acid such as lemon juice or vinegar.

• In case of eye contact, rinse abundantly with clean water for at least 10 minutes. Consult a physician.

• FIRE HAZARD! AVOID SHORT-CIRCUITING THE CONTACTS OF A DETACHED BATTERY. DO NOT INCINERATE THE BATTERY.

Charger Safety

• Use the charger provided with the tool only to charge the battery.

• Never attempt to charge non-rechargeable batteries.

• Have defective cords replaced immediately.

• Do not expose to water.

• Do not open the charger.

• Do not probe the charger.

• The charger is intended for indoor use only.

• This charger can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of

experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the

hazards involved.

• Children should not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

• CAUTION: Do not recharge non-rechargeable batteries.

Additional Safety Instructions

WARNING! SAWING CAN RESULT IN THE FORMATION OF HAZARDOUS DUSTS (E.G. ARISING FROM MATERIALS WITH PAINTS

CONTAINING LEAD, MATERIALS CONTAINING ASBESTOS, METALS OR SOME WOOD TYPES) WHICH CAN PRESENT A HAZARD TO

THE OPERATOR OR PERSONS IN THE VICINITY. MAKE SURE THAT THE WORKPLACE IS WELL VENTILATED. ALWAYS WEAR SAFETY

GOGGLES, SAFETY GLOVES AND RESPIRATORY PROTECTION. ATTACH A DUST EXTRACTION SYSTEM.

Safety Instructions for Reciprocating Saws

• Hold the power tool by insulated gripping surfaces, when performing an operation where the cutting accessory may contact hidden wiring. Cutting

accessory contacting a "live" wire may make exposed metal parts of the power tool "live" and could give the operator an electric shock.

• Use clamps or another practical way to secure and support the workpiece to a stable platform. Holding the workpiece by hand or against your

body leaves it unstable and may lead to loss of control.

Special Safety Information for the Cordless Combination Tool

• Hold the electric tool by the insulated handle surfaces when performing work where the cutting tool or screw may meet hidden wiring. Contact

with a live wire can also cause a charge in metal parts of the appliance and result in an electric shock.

• Use suitable detectors to find hidden supply lines or ask the local utility company. Contact with electrical cables can lead to electric shock and

fire, contact with a gas pipe can result in an explosion. Damage to a water pipe can lead to property damaged and electric shock.

• Secure the workpiece. A workpiece that is retained with clamping appliances or a vice is held more securely than with your hand.

• Be very careful when handling tools such as saws, scraper blades and drills. These are sharp and present an injury hazard.

• Wear safety gloves when changing attachments. This enables you to avoid injuries if the appliance attachment has heated up after use.

Specific Safety Instructions When Sawing

• Keep hands away from the sawing area. Do not reach underneath the workpiece. Always stand to the side of the saw when working. Upon

contact with the blade there is a risk of injury.

• Only when the electric tool is turned on should the sawing blade be moved against the workpiece. There is a risk of kickback if the tool insert

jams in the workpiece.

• Make sure that the footplate is securely placed against the workpiece during sawing. The sawblade can tilt and lead to loss of control over the

power tool.

• After you have finished work, turn the power tool off and do not pull the sawblade out of the cut until it has come to a standstill. In this way you will

avoid any kickback and can safely put down the power tool.

• Use only undamaged sawblades in perfect condition. Bent or blunt blades can break, adversely affect the cut or cause kickback.

• Do not brake the sawblade after applying side pressure. The sawblade may be damaged, break or cause switching the appliance off by a

kickback.

• Tighten the material firmly. Do not support the workpiece by hand or foot. Do not touch any objects or the ground with the saw running.

• There is a risk of kickback. Hold the power tool tightly with both hands while working and ensure a secure footing. The power tool is guided more

securely with both hands.

• Wait until the power tool has stopped before placing it down. The tool insert can tilt and lead to loss of control over the power tool.

• Switch the appliance off immediately if the sawing blade jams. Spread the saw cut out and pull the blade out carefully. This can lead to loss of

control over the power tool.

Residual Risks

Even if properly operating and handling this electric tool, some residual risks will remain. Due to its construction and build, this electric tool may

present the following hazards:

• Lung damage if suitable respiratory protection is not worn.

MT3 Multi-Tool Kit

• Cuts

• Ear damage if working without ear protection.

• Eye damage if suitable eye protection is not worn.

• Damage to your health caused by swinging your hands and arms when operating the appliance for longer periods of time or if the unit is not held

or maintained properly.

MT3 Multi-Tool Kit

Safety Symbols

The product may have safety warning labels attached to it, explained below. Understand the symbols on your

product and their meanings. If any stickers become unreadable, unattached etc., replace them.

Flammable Material Hazard

Flammable liquids, gases, or

substances etc may present.

Avoid ignition sources and open

flames. Danger of fire.

Read User Manual

Read and fully understand

product safety warnings,

operation, procedures etc before

using the product.

Use Hand Protection

Wear appropriate hand protection

and take due care as the product

or use of the product may present

hand hazards.

Carbon-Monoxide Hazard

Do not use the product in

confined areas or without

adequate ventilation. Carbon-

monoxide poisoning can be fatal.

Electrocution / Electrical Shock

Hazard

High voltage or high current

electricity may be present or

required by the product. Take

due care when handling electrical

products, cables, plugs and

leads. Electrical shock can be

fatal.

Toxic Fumes / Dust Hazard

Using the product or by-products

from use may produce fumes,

smoke or particles that could be

harmful if inhaled. Wear

appropriate breathing protection

and have adequate ventilation.

Explosive Material Hazard

Combustible liquids, gases, or

substances etc may be present.

Avoid ignition sources and open

flames. Danger of explosion.

Cutting / Amputation Hazard

The product may have blades,

edges or mechanical devices that

can cause severe cut injury to

fingers, limbs etc. Take due care

when handling and using the

product.

Crush Hazard

The product may have blades,

edges or mechanical devices that

can cause severe crush injury to

fingers, limbs etc. Take due care

when handling and using the

product.

Single Operator Only

The product must be operated by

a single person only. More than

one person operating the product

may introduce additional hazards.

Use Face Protection

Wear appropriate full-face

protection and take due care as

the product or use of the product

may present face and eye

hazards.

Use Foot Protection

Wear appropriate foot protection

and take due care as the product

or use of the product may present

foot hazards.

Use Eye / Ear / Head Protection

Wear appropriate eye and / or

ear and / or head protection and

take due care as the product or

use of the product may present

eye, hearing, and head hazards.

Running Hazard

Do not run on or near the product

as doing so may present a fall

hazard.

Diving Hazard

Do not dive into the product as

doing so may present a neck /

head injury hazard.

Adult Supervision Required

Always supervise children and

other users of a product to

prevent drowning or injury.

Skin Penetration / Puncture

Hazard

The product may produce

pressure, emit liquids or objects

that can cause severe injury to

fingers, limbs, blood etc. Take

due care when handling and

using the product.

Hot Surface Hazard

Be aware that the product may

produce high temperatures and

hot surfaces that can cause burn

injuries.

Flying Debris Hazard

Be aware that the product or use

of the product may present

hazards produced by flying

debris. Wear appropriate clothing

and protective devices.

Moving Parts Hazard

Be aware that the product

contains or uses mechanical

devices that move or rotate.

Always wait for moving parts to

stop fully before handling the

product, adjusting, maintenance

etc.

MT3 Multi-Tool Kit

Carbon-Monoxide Hazard

Do not use the product in

confined areas or without

adequate ventilation. Carbon-

monoxide poisoning can be fatal.

Pull Hazard

Be aware that the product

contains or uses mechanical

devices that can pull in objects

and can cause severe injury to

fingers, limbs etc. Take due care

when handling and using the

product.

Slope / Fall Injury Hazard

Be aware that using the product

on sloping surfaces or in slippery

conditions may present additional

dangers from falls and contact

with blades, moving parts, hot

surfaces etc.

"Slam Dunk" Warning

Do NOT attempt "slam dunk"

manoeuvres as this may result in

severe injury due to falling,

product breakage or collapse etc.

Electrocution / Electrical Shock

Hazard - Outdoor

High voltage or high current

electricity may be present or

required by the product. Do NOT

use in rain, damp, or wet

conditions. Electrical shock can

be fatal.

Electrocution / Electrical Shock

Hazard - Disconnect

High voltage or high current

electricity may be present or

required by the product. Always

disconnect the product from the

electrical supply before handling

the product, adjusting,

maintenance etc.

Power Line Electrocution

Hazard

High voltage / high current power

lines may be present. Use

extreme caution to avoid contact

or interference with power lines.

Electrical shock can be fatal.

"Kick-Back" Hazard

High level of "kick-back" hazard

that can cause the machine to

suddenly rotate towards operator.

Kick-back injury can be fatal.

Winch Operator Position

Hazard

Do NOT stand between winch

and load. Do NOT use winch to

move people.

Winch Lift Hazard

Do NOT LIFT load vertically. Use

machine to PULL only.

Cable Hazard

Ensure that load bearing cable is

not kinked or knotted.

Winch Cable Hazard

Ensure that there is a minimum

number of cable coils on

winching mechanism.

Winch Hook Hazard

Carry hook to load – do NOT

throw or run.

Flash / Blinding Hazard

Wear appropriate eye protection

for welding. Direct exposure to

weld arcs may cause permanent

eye injury.

Laser Hazard

Laser may be in use – do NOT

look directly at laser or allow

others to.

MT3 Multi-Tool Kit

Table of Contents

Safety ............................................................................................................................................................. 2

Safety Symbols ........................................................................................................................................................... 7

Parts Identification ..................................................................................................................................... 10

Assembly ..................................................................................................................................................... 11

Operation ..................................................................................................................................................... 12

Charging the Battery Pack ........................................................................................................................................ 12

Replacing Attachments ............................................................................................................................................. 13

Switching ON/OFF .................................................................................................................................................... 13

Motor Unit with Drill Attachment ............................................................................................................................... 13

Motor Unit with Jig Saw Attachment ......................................................................................................................... 14

Motor Unit with Multi-Function Tool .......................................................................................................................... 15

Practical Tips ............................................................................................................................................................ 15

Sawing ...................................................................................................................................................................... 15

Scraping .................................................................................................................................................................... 16

Lithium Battery Care and Maintenance .................................................................................................... 17

Top 3 Battery Care Requirements ............................................................................................................................ 17

Maintenance ................................................................................................................................................ 19

Storage ........................................................................................................................................................ 19

Specifications ............................................................................................................................................. 20

MT3 Multi-Tool Kit

Parts Identification

No. Name No. Name

1 MT3 20V Lithium Oscillating Multi-Tool 7 Assorted blades

2 Scraper blade head 8 Assorted drill bits

3

Charger

9

Sander head

4

Plunge saw head

10

Battery

5

Oscillating tool accessories

11

Assorted drill bits

6

3x sandpapers (60, 80, & 120 grit)

1

2

3

4

6

5

7

8

9

10

11

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

MT3 Multi-Tool Kit

Assembly

1. Remove all packaging materials.

2. Remove remaining packaging and packing inserts (if included).

3. Check that the package contents are complete.

4. Check the appliance, the power cord, the power plug of charger and all accessories for transportation are

damage or not.

5. Keep the packaging materials as far as possible until the end of the warranty period. Then take it to your

local waste disposal system.

WARNING! PACKAGING MATERIALS ARE NOT TOYS! CHILDREN MUST NOT PLAY WITH

PLASTIC BAGS! THERE IS A DANGER OF SUFFOCATION!

Accessories

NOTE: If any parts are missing or damaged, please contact the manufacturer.

Check the Parts Identification section for the complete list of accessories supplied.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

MT3 Multi-Tool Kit

Operation

Charging the Battery Pack

IMPORTANT: The battery pack is not fully charged at the factory. Before attempting to charge

them, thoroughly read all the safety instructions first.

1. Ensure that the charger you use are applicable to the battery pack.

2. Insert the charger into the outlet. The indicator light (3) turns to green to indicate that the power is

connected.

3. Insert the end of the charger (1) into the battery slot (2). Make sure the contact with the charger is correct.

4. When charging, the indicator light (3) turns to red.

5. When fully charged, the indicator light (3) turns to green again.

6. Frequently monitor the charger and battery pack while connected.

7. Unplug the charger and disconnect it from the battery pack when finished.

8. Allow the battery pack to cool completely before using it.

9. Store the charger and battery pack indoors, out of reach of children.

NOTE: If the battery does not fit properly, disconnect it, and confirm that the battery pack is the

correct model for this charger. Do not charge any other battery pack or any battery pack that

does not securely fit the charger.

If battery is hot after continuous use in the tool, allow it to cool down to room temperature before

charging. This will extend the life of your batteries.

Remove battery pack from charger stand which use your thumb or fingers, press the battery’s release

button in and pull the battery pack off at the same time.

Battery Capacity Indicator

There are battery capacity indicators on the battery pack; you can check the capacity status of the battery if you

squeeze the button. Before using the machine, please press switch trigger to check if the battery is full enough

for properly working. Those 3 LED might show the status of the capacity level of the battery

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

MT3 Multi-Tool Kit

Inserting and Removing the Battery

WARNING: Before making any adjustments, ensure the drill is switched OFF with the direction of

the rotation selector in the centre position

•

Removing the battery: press the battery release latch in and at the same time pull the battery pack off.

•

To insert the battery, push the battery pack onto the contacts of the tool.

Replacing Attachments

WARNING! Secure the appliance against switching ON (see Switching ON/OFF below) or remove

the rechargeable battery from the appliance. There is an injury hazard if the device is switched

ON accidentally.

Removing Attachments

1. Push the unlocking lever into position as far as the stop and then hold it in this position.

2. Pull the unlocked appliance attachment OFF.

3. Allow the unlocking lever to slide back into position.

Fitting Attachments

1. Push the attachment along the guide rail into the motor unit. It should lock in place with an audible click.

2. Allow the unlocking lever to slide back into position.

3. Check that the attachment is secure by pulling on it.

Switching ON/OFF

•

Switching ON: Press the ON/OFF switch. You can progressively control the speed.

− Gentle pressure: low speed

− Increase pressure: higher speed.

•

Switching OFF: Release the ON/OFF switch. If you place the direction switch in the middle position, the

device is secured against being switched ON.

Motor Unit with Drill Attachment

Changing the Tool

1. Rotate the keyless chuck anti-clockwise, until the drill chuck aperture is large enough to accommodate the

tool.

2. Insert the tool as far as possible into the keyless chuck.

3. Rotate the keyless chuck clockwise to clamp the tool.

4. To remove the tool again, rotate the keyless chuck and pull out the tool.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

MT3 Multi-Tool Kit

Choice of Gear

WARNING! STOP APPLIANCE BEFORE CHANGING GEAR TO AVOID DAMAGING THE TOOL.

1. Wait for the appliance to come to a standstill.

2. Slide in the gear selector into the required position:

− L: low speed

− H: high speed

Setting the Rotation Direction

The appliance’s direction of rotation can be changed with the rotational direction switch.

1. Wait for the appliance to come to a standstill.

2. Push the rotational direction speed into the desired position:

− Clockwise rotation: to drill and screw in screws.

− Anti-clockwise rotation: to unscrew screws.

3. If you place the direction switch in the middle position, the device is secured against being switched ON.

Torque Adjustment

You can pre-select the maximum torque.

The torque settings are labeled 1 - 19 +

1. Wait for the appliance to come to a standstill.

2. Turn the torque adjusting ring (2) to select the desired torque:

− Screws: Steps 1 - 19; Drilling: Step

3. Start with a lower torque step and increase as required.

NOTE: The necessary torque is dependent on:

− The type and hardness of the material to be treated.

− The type and length of the screws used.

Motor Unit with Jig Saw Attachment

WARNING! Secure the appliance against switching ON (see Switching ON/OFF). If the appliance

is switched ON accidentally, there is a danger of injury!

CAUTION, RISK OF INJURY! Do not use any blunt or bent blades or blades which are damaged in any

other way. Always insert a suitable sawblade.

Installing the Blade

1. Push the lever for the sawblade, unlocking it in an upward motion until it comes to a stop. Push the sawblade

shaft into the sawblade mounting slot.

2. To unlock, release the lever; it will return to the initial position.

3. Ensure that the sawblade is secure by pulling on it.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

MT3 Multi-Tool Kit

Removing the Sawblade

Press the lever for the sawblade, unlocking it in an upward motion until it comes to a stop, and then pull out the

sawblade from the sawblade mounting.

Operating the Jig Saw

1. Before switching the appliance ON, ensure it is not in contact with the workpiece.

2. Turn the appliance ON. By using the ON/OFF switch, you can increase or decrease the stroke rate.

− Gentle pressure: low stroke rate.

− Greater pressure: higher stroke rate.

The ON/OFF switch cannot be locked.

3. Place the footplate on the workpiece.

4. Cut with a uniform forward motion.

5. After completion of the work, carefully remove the blade from the tool first and then switch the appliance

OFF.

Motor Unit with Multi-Function Tool

Changing the Tool

WARNING! Secure the appliance against switching ON (see Switching ON/OFF). If the appliance

is switched ON accidentally, there is a danger of injury!

1. Push the lever for unlocking the tool upwards until it comes to a stop.

2. Pull the unlocked tool holder forward.

3. Place the required tool on the arbor. 12 different positions are possible.

4. Press the tool holder back into the central mounting.

5. Push the lever for unlocking the tool forward again. The tool holder is now secured to the tool.

Practical Tips

•

When working with the appliance, always wear suitable clothing and appropriate protective equipment.

•

Prior to each use, ensure that the appliance is working correctly.

•

Wearing personal protective equipment and a fully functional appliance can reduce the risk of injuries and

accidents.

Sawing

•

Use only undamaged sawblades in perfect condition. Only use metal sawblades for metalworking.

•

Ensure your stance is secure and stable. Hold the appliance tightly with both hands and away from your

body.

•

Before sawing the workpiece, check for hidden foreign objects, such as nails and screws. These must be

removed first.

•

Plunge cuts should only be made in soft material such as wood or plasterboard.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

MT3 Multi-Tool Kit

Sawblade Selection

•

Wood sawblade for wood, plastic, plasterboard

•

Metal sawblade for metal sheets, profiles, and tubes

Scraping

•

Use a high oscillation rate when scraping.

•

Work using low pressure and at a low angle to avoid damaging the substrate material.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

MT3 Multi-Tool Kit

Lithium Battery Care and Maintenance

Top 3 Battery Care Requirements

1. Charge battery before first use. The battery may arrive with some charge, regardless of this the

battery must be charged on the initial charge and for each subsequent charge.

2. Charge battery immediately when it is depleted. Do not store a depleted battery. This will

permanently impact the life of the battery. If the battery is going to be stored for a period of time, fully

charge the battery before storing.

3. Disconnect battery when not in use. To prolong the life of a battery, disconnect it from the unit

when not in use. Disconnect chargers from the battery once charged.

To ensure the battery maintains optimum performance, follow the guidelines outlined below.

•

For best results, charge batteries in temperatures between 10°C and 30°C

•

When battery is charged, disconnect the charger from the power supply and remove the battery from the

charger.

•

If a battery is stored or otherwise unused for an extended period, and the battery has no charge remaining

when you check it, consider it to be damaged. Do not attempt to recharge it or to use it. Replace it with a

new battery.

•

Use only with the battery charger specified by the manufacturer.

•

Ensure that the battery charger electrical cord is not subjected to damage or stress. Do not operate the

battery charger if it has a damaged electrical cord or plug.

•

Do not use the charger in wet areas or expose it to rain or water.

•

The typical estimated life of a Lithium-Ion battery is about two to three years or 300 to 500 charge cycles,

whichever occurs first. One charge cycle is a period of use from fully charged, to fully discharged, and fully

recharged again

•

Explosion hazard – protect the battery against heat, for example, direct sunlight and fire. Do not store

batteries in vehicles or locations subject to heat.

•

Batteries can explode in the presence of an ignition source, such as a pilot light. To reduce the risk of

serious personal injury, never use any cordless product in the presence of open ﬂame. Exploding batteries

can propel debris and chemicals.

•

Do not open the battery – danger of short-circuiting and/or explosion.

•

Do not attempt to destroy or disassemble the battery pack or remove any of its components.

•

Do not touch the battery terminals with metal objects and/or body parts as short-circuit and/or personal injury

may result.

•

Explosion hazard – do not open and/or short-circuit the battery.

•

Poison hazard – battery leakage (liquid ejection). Under extreme conditions, liquid may be ejected from the

battery – avoid contact. If contact accidentally occurs, immediately seek medical attention, and flush with

water. If liquid contacts eyes, immediately seek medical attention, flush with clean water for at least 10

minutes. Liquid ejected from the battery may cause irritation or burns.

•

Dispose of non-serviceable batteries in an environmentally responsible manner and according to local

regulations.

Failure to adhere to the requirements above may result in the battery becoming inoperative or battery life being

reduced. In extreme cases or abuse, battery overheating or fire may result.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

MT3 Multi-Tool Kit

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

MT3 Multi-Tool Kit

Maintenance

NOTE: Repair and servicing work not described in this manual should always be carried by an

authorised service centre. Use only original parts. Switch OFF the device and remove the battery

from the device before working with or transporting it. The following cleaning and servicing should be

done regularly. This will ensure a long and reliable service life.

Cleaning

•

Do not spray the appliance with water and do not immerse it in water. Electric shock hazard!

•

Keep clean the ventilation slots, motor housing and handles of the appliance. Use a damp cloth or a brush.

•

Do not use cleaning agents or solvents. You can irreparably damage the appliance.

Maintenance

The equipment is maintenance free.

Storage

•

Store the device in a dry place, well out of reach of children.

•

Remove the battery before storing the unit for longer periods of time.

•

Store the battery only in a partially charged state. The state of charge should be 40 – 60% over a longer

storage period (two LED lights of the charge status indicator (9a) light up).

•

During a longer storage period, check the charged state of the battery and recharge if necessary, roughly

every 3 months.

•

To keep the battery well charged, avoid exposing the appliance to extreme heat or cold in storage.

•

Store the equipment between 10 and 25°C. During storage, avoid extreme cold or heat so the battery does

not lose power.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

MT3 Multi-Tool Kit

Specifications

Torque 40Nm

Battery 20V 2Ah

Oscillating Angle 3°

No-load Speed 0-21000/min

Speed Modes 2

Charger 240V

LED Worklight Yes

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Some experts believe that the incorrect or prolonged use of almost any

product may cause serious injury or death. To help reduce your risk of

serious injury or death, refer to the information below. For more information,

see www.datastreamserver.com/safety



Consult all documentation, packaging,

and product labelling before use. Note

that some products feature

documentation available online. It is

recommended to print and retain the

documentation.



Before each use, check the product for

loose/broken/damaged/missing parts,

wear, or leaks (if applicable). Never use a

product with

loose/broken/damaged/missing parts,

wear, or leaks.



Products must be inspected and serviced

(if applicable) by a qualified technician

every 6 months. This is based on

average residential use by persons of

average size and strength, and on a

property of average metropolitan size.

Use beyond these recommendations may

require more frequent

inspections/servicing.



Ensure that all users of the product have

completed a suitable industry recognised

training course before being allowed

access to the product.



The product has been supplied by a general merchandise

retailer that may not be familiar with your specific

application or description of application. Be sure to attain

third-party approval from a qualified specialist for your

application before use, regardless of any assurances from

the retailer or its representatives.



This product is not intended for use where fail-safe

operation is required. As with any product (for example,

automobile, computer, toaster), there is the possibility of

technical issues that may require the repair or

replacement of parts, or the product itself. If the possibility

of such failure and the associated time it may take to

rectify could in any way inconvenience the user, business,

or employee, or financially affect the user, business, or

employee, then the product is not suitable for your

requirements. This product is not intended for use where

incorrect operation or a failure of any kind, including but

not limited to, a condition requiring product return,

replacement, parts replacement, or service by a

technician may cause financial loss, loss of employee

time or an inconvenience requiring compensation.



If this product has been purchased in error when

considering the information presented here, contact the

retailer directly for details of their returns policy, if

required.

ideas, diagrams, or images may be reproduced or transmitted in any form or by any means, electronic or

mechanical, including photocopying, scanning, or recording, or any information storage and retrieval system,

without express permission or consent from the publisher.

BAUMR-AG TOLCLSBMRAMT3 Cordless MT3 20V SYNC 3in1 Combi-Tool Kit

Product's Documents

Product manual

Specifications

BAUMR-AG TOLCLSBMRAMT3 Questions and Answers