Loading ...
Loading ...
Loading ...
4
Connector Capacity Matrix
Connector Type Capacity Range
Industrial
Copper
Copper Splices #8 - 750 MCM
Copper Lugs #8 - 750 MCM
Copper "C" Taps #14sol - 500 MCM
Aluminum
Aluminum Splices #8 - 750 MCM
Aluminum Lugs #8 - 750 MCM
Aluminum Pin Adapters #6 - 750 MCM
Aluminum "H" Taps #8 - 500 MCM
Grounding
Ground Grid Connectors #8 - 500 MCM
Copper "E" Taps #8 - 500 MCM
Overhead
Copper
Copper Tension Splice #8sol - 500 MCM
Copper Lugs 1/0 - 500 MCM
Copper "H" Taps #12 - 4/0
Aluminum
Aluminum Tension Splice #6 - 587.5 MCM
Aluminum Stirrups #6 - 500 MCM
Aluminum Lugs #4 - 556.5 MCM
Aluminum Jumper Splice #4 - 556.5 MCM
Aluminum "H" Taps #8 - 500 MCM
ASCR
ASCR One Piece Tension Splice #6 - 587.5
ASCR Two Piece Tension Splice #4 - 556.5 MCM
ASCR Stirrups #6 - 477
5/8" Service Entrance Connectors #10 - 1/0
840 Service Entrance Connectors 1/0 - 4/0
ASSEMBLY
WARNING
Recharge only with the charger
specied for the battery. For spe-
cic charging instructions, read the operator’s
manual supplied with your charger and battery.
Removing/Inserting the Battery
To remove the battery, push in the release buttons
and pull the battery pack away from the tool.
WARNING
Always remove battery pack before
changing or removing accessories.
To insert the battery, slide the pack into the body
of the tool. Make sure it latches securely into place.
WARNING
Only use accessories specically
recommended for this tool. Others
may be hazardous.
An incomplete or faulty crimp could cause a re.
Use tool only with "U" dies and connectors for
which they are rated. Jaws, dies, and connectors
must be used in an approved combination to
achieve a successful operation. Improper combi-
nations can result in a faulty crimp. Electric shock,
re, explosion, and property damage could occur.
Changing the Dies
Inspect dies and connectors before use. Only use prop-
erly matched dies and connectors for the crimping jaws.
Refer to Specications for die/connector compatibility.
1. Remove the battery pack.
2. Snap the appropriate dies into each side of the
crimping jaws.
3. To remove, press the release button for each side of
the crimping jaws. Pull dies out from crimping jaws.
ONE-KEY™
To learn more about the ONE-KEY™ function-
ality for this tool, please reference the Quick
Start guide included with this product or go to
milwaukeetool.com/One-Key. To download the
ONE-KEY™ app, visit the App Store or Google Play
from your smart device.
ONE-KEY™ Indicator
Solid Blue Wireless mode is active and ready to
be congured via the ONE-KEY™ app.
Blinking Blue Tool is actively communicating with
the ONE-KEY™ app.
Blinking Red Tool is in security lockout and can
be unlocked by the owner via the
ONE-KEY™ app.
OPERATION
WARNING
To reduce the risk of arc ash,
electric shock and property
damage, work on deenergized lines when
possible. Tool is not insulated. Should work
on energized lines be required, ensure all proper
precautions, including those contained in NFPA
70E, have been taken rst.
Keep hands away from crimping jaws
while tool is in use. Fingers could be
crushed.
Always remove battery pack before changing
or removing accessories. Only use accessories
specically recommended for this tool. Others
may be hazardous.
Always wear proper eye protection marked to
comply with ANSI Z87.1.
When working in dusty situations, wear appro-
priate respiratory protection or use an OSHA
compliant dust extraction solution.
Crimping
Before crimping:
•
Inspect the jaws and dies for cracks or other dam-
age. Do not use damaged jaws or dies. Contact a
MILWAUKEE
service facility.
•
Ensure dies are properly installed.
•
Jaws, dies, connectors, and cables must
be used in
an APPROVED COMBINATION
. Improper combi-
nations can result in a faulty crimp.
Loading ...
Loading ...
Loading ...