1
Operation Guide 5344/5384
To change the day indicator setting
To adjust the time setting
Pull the Crown out to Click 1.
Push the Crown back in.
Push the Crown back in.
Rotate the Crown to change the
time setting.
When the second hand is at
12 o’clock, pull the
Crown out to
Click 2.
Rotate the Crown to set the day.
Note
x
Take care that you set the correct AM
or PM time.
x
When changing the time, move the
minute hand four or fi ve minutes past
your fi nal setting, and then back it up
to the setting you want.
Note
x
The day indicator setting uses a 31-
day month. Make adjustments for
months of shorter lengths.
x
Avoid changing the day indicator
setting between the hours of 9
p.m. and 1 a.m. Otherwise, the day
indicator may not change correctly at
midnight.
Specifi cations
Accuracy: ±20 seconds average per month
Stopwatch: Measuring Capacity: 59'59" (60 minutes)
Measuring Unit: 1 second
Measurements: Elapsed time; split time; two fi nishes
Battery: One silver oxide battery (Type: SR920SW)
Battery Life: Approximately 2 years (60 minutes stopwatch operation per day)
Crown Operations
Some water-resistant models (100 meters, 200 meters)
have a screw-in crown. When you need to perform a crown
operation, rotate it towards you to unscrew it. Then pull
the crown out. Avoid applying undue force when pulling.
The watch loses its water resistance while the crown is
unscrewed. After performing a crown operation, fully screw
the crown back in.
Crown
Loosen
If your watch has a rotary bezel...
You can rotate the bezel to align its
▼
mark with the
minute hand. Then you will be able to tell how much
time has elapsed since aligning the
▼
mark.
Start
Elapsed time
Current
x Your watch may differ somewhat from the one shown in the illustration.
x Some models may use a combination of hands and rotating disks to indicate
information. The word “hand” in this section is used to mean both analog hands
and rotating disks.
x The dials of some models have double-ended hands. Depending on the data,
either end can be used for indication.
Perform the following procedure if the stopwatch hands do not return to their 0 (zero)
positions when you reset the stopwatch.
Correcting the 0 Positions of the Hands
Pull the Crown out to Click 2.
Use B (clockwise) and A (counterclockwise) to move the
Stopwatch Second Hand
and
Stopwatch Minute Hand
to 12 o'clock.
x Holding down either button will move the second hand at high speed, until you
release the button.
x The
Stopwatch Minute Hand
is syncronized with the
Stopwatch Second Hand
.
After all of the hands are the way you want, push the Crown back in.
Important!
x
Timekeeping stops while the crown is pulled out. Correct the current time setting
after performing the above operation.
Using the Stopwatch
Important!
x
Do not operate the stopwatch with the crown pulled out.
Note
x
An elapsed time operation will stop automatically at the end of 60 minutes.
The stopwatch measures elapsed time in 1-second increments up to 59minutes,
59seconds.
Elapsed time
A
A
A A
B
Start Stop Resume Stop Reset
Split time
A
B
B A
B
Start Split Split release Stop Reset
Two fi nishes
A
B
A B
B
Start Split
First runner
fi nishes.
Display time of
fi rst runner.
Stop
Second runner
fi nishes.
Split release
Display time of
second runner.
Reset
Stopwatch functions
Second Hand
Day Indicator
Click 2
Click 1
Hour Hand
Minute Hand
A
B
Crown
Stopwatch Minute Hand
24 Hour Hand
Stopwatch Second Hand
MA2202-EB
Ú
#!3)/#/-054%2#/,4$
