Loading ...
Loading ...
Loading ...
5
ASSEMBLY
WARNING
Recharge only with the charger
specied for the battery. For spe-
cic charging instructions, read the operator’s
manual supplied with your charger and battery.
Removing/Inserting the Battery
To remove the battery, push in the release buttons
and pull the battery pack away from the tool.
WARNING
Always remove battery pack before
changing or removing accessories.
To insert the battery, slide the pack into the body
of the tool. Make sure it latches securely into place.
WARNING
Only use accessories specically
recommended for this tool. Others
may be hazardous.
Inserting/Removing the Crimping Jaws
1. Remove the battery pack.
2. Remove the locking thumb screw (when used)
from the back of the retaining pin.
3. Push in, then rotate the retaining pin counterclock-
wise 90° . The pin will pop out.
4. Insert the crimping jaws. Line up the center hole
with the retaining pin.
5. Push in the retaining pin, then rotate clockwise
90° .
6. Insert and hand tighten the locking thumb screw.
NOTE: Use the locking thumb screw to prevent the
retaining pin from being unintentionally loosened.
A loose retaining pin may damage the tool.
7. Rotate the jaws to the desired angle.
CAUTION
To avoid damage to the tool, do not
operate the tool without the retain-
ing pin fully inserted and locked into position.
Damage to the cylinder may occur.
WARNING
An incomplete or faulty crimp could
cause a re. Jaws, dies, and con-
nectors must be used in an APPROVED COM-
BINATION to achieve a successful operation.
Improper combinations can result in a faulty
crimp. Electric shock, re, explosion, and prop-
erty damage could occur.
Changing the Dies
Inspect dies and connectors before use. Only use
properly matched dies and connectors for the ap-
propriate crimping jaws. Refer to Specications for
die/connector/crimping jaws compatibility.
1. Remove the battery pack.
2. Push in the retaining pins and snap the appropriate
dies into each side of the crimping jaws. Release
the retaining pins.
3. To remove, push in the retaining pins pull dies out
from crimping jaws.
ONE-KEY™
To learn more about the ONE-KEY™ functionality for
this tool, please refer to the quick reference included with
this product or go to milwaukeetool.com/One-Key. To
download the ONE-KEY™ app, visit the App Store or
Google Play from your smart device.
ONE-KEY™ Indicator
Solid Blue Wireless mode is active and ready
to be congured via the ONE-KEY™
app.
Blinking Blue Tool is actively communicating with
the ONE-KEY™ app.
Blinking Red Tool is in security lockout and can
be unlocked by the owner via the
ONE-KEY™ app.
Cutting Jaws (not included)
The Utility Crimper is compatible with the following
MILWAUKEE cutting jaws. Refer to the cutting jaws'
instructions for use.
Jaw Type Maximum Capacity
477 ACSR Jaws
(Cat. No. 49-16-2773)
ACSR: 477 MCM Hen ACSR
Guy Wire: 3/8" Non-EHS
Rebar: 3/8"
Ground Rod: 3/8"
750 MCM Cu/Al Jaws
(Cat. No. 49-16-2772)
Copper Cable: 750 MCM
Aluminum Cable:
1000 MCM *
1/2" EHS Guy Wire
Jaws
(Cat. No. 49-16-2777)
EHS Guy Wire: 1/2"
(19 strand) **
Non-EHS Guy Wire: 1/2"
(7 & 19 strand) **
ACSR: 4/0 AWG
Rebar: 3/8"
Ground Rod: 3/8"
Fine Stranded Wire
Jaws
(Cat. No. 49-16-2778)
Fine Stranded Wire:
1/0 AWG - 777.7 AWG ***
*750 MCM Cu Jaws will cut any aluminum cable with a
diameter less than 1.225"
**May require two cutting cycles to complete cut on 1/2" wire
***Jaws should only be used on the following wire classes:
M, K, I/DLO
Loading ...
Loading ...
Loading ...