Loading ...
Loading ...
Loading ...
5
To remove fastener strips:
1. Remove battery pack.
2. WARNING! Always point the tool away from yourself
and others when installing fasteners. Failure to do
so could result in injury.
3. Press the pusher release button and slide the maga-
zine open.
4. Remove the fasteners.
OPERATION
WARNING
To reduce the risk of injury, always
wear safety goggles or glasses
with side shields.
The operator and other people
in the work area must wear eye protection in ac-
cordance with ANSI Z87.1. Eye protection does not
t all operators in the same way. Make sure the eye
protection chosen has side shields or provides
protection from ying debris both from the front
and sides. The employer is responsible for enforc-
ing the use of eye protection by the operator and
other people in the work area. When required, wear
head protection in accordance with ANSI Z89.1.
To reduce the risk of injury to yourself and others,
test the tool before beginning work each day ac-
cording to the "Required Daily Testing" section.
Do not use the tool unless you thoroughly under-
stand the actuation mode selected.
Remove battery pack and fasteners before leaving
the work area, moving the tool to another location,
or handing the tool to another person. Failure to do
so could result in serious injury.
Do not use this tool for fastening electrical
cables. It is not designed for electric cable
installation and may damage the insulation of
electric cables thereby causing electric shock
or re hazards.
NEVER wedge or hold back the workpiece contact
mechanism during operation of the tool. Never
attempt to clear a jammed workpiece contact by
grasping the discharge area of the tool. Doing so
could result in serious injury.
To avoid serious injury, do not attempt to prevent
the recoil by holding the tool too rmly against
the work. Keep face and body away from the tool.
During normal use, the tool will recoil immediately
after driving a fastener. This is a normal function
of the tool. Restriction to the recoil can result in a
second fastener being driven when the tool is in
Contact Actuation mode. Grip the handle rmly,
let the tool do the work, and do not place a second
hand on top of the tool.
Power/Actuation Selection
1. Install battery pack.
2. Press and hold the Power/Actuation button to
turn on the tool.
Power/Actuation Button
Power
Indicator
Actuation
Indicator
3. Press the Power/Actuation button again to toggle
between single sequential actuation mode and
contact (bump) actuation mode.
WARNING! Understand actuation process before use.
Single Sequential Actuation -
Solid Light -
The workpiece contact and
then the trigger must be activated in a
specic sequence to drive a fastener.
Contact (Bump) Actuation -
Flashing Light -
The workpiece contact
and the trigger can be activated in any
sequence to drive a fastener.
4. Press and hold the Power/Actuation button to
turn o the tool.
Single Sequential Actuation Operation
1. Grip the handle rmly.
2. Push the tool against the work surface, compressing
the workpiece contact.
3. Pull the trigger to drive the fastener. WARNING! To
avoid serious injury, do not attempt to prevent the
recoil by holding the tool too rmly against the work.
4. Remove your nger from the trigger and remove the
tool from
the workpiece.
Contact (Bump) Actuation Operation
Contact Actua
tion can follow two dierent sequences,
depending on your use.
Multiple actuations:
1. Grip the handle rmly.
2. Pull and hold the trigger.
3. Push the tool against the work surface, compress-
ing the workpiece contact to drive the fastener.
WARNING! To avoid serious injury, do not attempt
to prevent the recoil by holding the tool too rmly
against the work.
4. Continue to hold the trigger and repeat workpiece
contact.
Single actuation:
1. Grip the handle rmly.
2. Push the tool against the work surface, compressing
the workpiece contact.
3. Pull the trigger to drive the fastener. WARNING! To
avoid serious injury, do not attempt to prevent the
recoil by holding the tool too rmly against the work.
4. Remove your nger from the trigger and remove the
tool from the workpiece.
Loading ...
Loading ...
Loading ...